Hayward AquaRite series Bedienungsanleitung

AquaRite®

Consumer Troubleshooting Guide

Safety Precautions

Warning

High Voltage Electrocution Hazard

Hazardous voltage can shock, burn, cause serious injury

and or death. To reduce the risk of electrocution and or

electric shock hazards:

•Only qualified technicians should remove the dead front

•Qualified technicians should: replace damaged

wiring immediately

•Qualified technicians should: Insure panel is properly

grounded and bonded

Table of Contents

How

AquaRite® Works & Chemistry Requirements

Pg.

How To:

Pg.

Change Metric to Standard & Change Default Reading

Set

TurboCell® Type & Reset Average Salt

Adjust

Chlorine Output & Clean TurboCell

Troubleshooting:

Pg.

1. Check Salt & Inspect Cell: flashing or ON

2. High Salt: LED ON

3. No Flow: LED flashing or ON

4. Display ONLY, Lights ONLY, or Neither

5. LCD: Displaying “HOT” or “COLD”

Additional Information:

Pg.

Salt Addition Table

Chlorine Output & Salt Levels

AquaRite: How It Works

•The AquaRite Salt Chlorine Generator is

designed to convert 99% pure salt into chlorine

gas (HOCl).

•The conversion occurs in the Electrolytic Cell,

also known as the TurboCell® (used throughout

this guide).

•Power is sent from the AquaRite Control Center

to the TurboCell, when chlorine production is

scheduled (based on time percentage).

•When power is applied to the TurboCell,

conductive plates produce a field; which in-turn

establishes an electrochemical reaction between

Chloride ions & the water to create

Hypochlorous Acid.

AquaRite: Chemistry Requirements

AquaRite®

How To:

How To: Switch from Metric to US Standard

If the first reading (average salt) is displayed in decimal form instead of a number

represented in thousands, then the unit has been set to ‘Metric Mode’.

Step 3 Step 4

Step 1

3.20

To change the unit from Metric Mode to US Standard, start by

pressing the ‘Diagnostics’ button one time.

Immediately the temperature reading should change to reflect a

Fahrenheit value. If it does not repeat step 2.

After 30 seconds the unit should settle back to the default

reading. The reading should now reflect a number in thousands.

Once showing the temperature in Celsius, move the switch up to

‘Super Chlorinate’ then back to ‘Auto’.

86 3200

Step 2

NOTE: The process is the same to go from US Standard to Metric.

How To: Change the Default Display

If the first reading represents a number followed by the letter ‘P’, then the default

reading has been changed to express the ‘Desired Output %’.

Step 2

To change the default reading back to the average salt, start by

pressing the ‘Diagnostics’ button two times.

Continue moving the switch up to ‘Super Chlorinate’ and back to

‘Auto’ until the display reads ‘AL-0’.

It takes about 30 seconds for the unit to settle back on the

default reading. It should now reflect the average salt level.

When the unit reads ‘AL-4’ move the switch up to ‘Super

Chlorinate’ and back to ‘Auto’.

77P AL-4

AL-0 3200

Step 1

Step 3 Step 4

How To: Set TurboCell Type

Before operation, the AquaRite must be configured to the correct TurboCell installed.

“t-15” is the factory default. If the incorrect cell is chosen the salt level will be

inaccurate and the system will likely suspend chlorination as a result.

Start with the main toggle switch in the ‘Auto’ position.

To change cell type, cycle slide switch up to ‘Super Chlorinate’. Return switch to ‘AUTO’. Repeat until display shows correct cell.

Push the diagnostics button until ‘t - 15, t - 9, t -5 , t - 3’ appears.

3200 t-15

t-3 t-9

Step 2

Step 1

Step 3 Step 4

How to: Reset Average Salt Level

The Average Salt level needs to be reset after initial start up, after a board

replacement, following major pool chemistry adjustments, and when a cell is replaced.

Step 3 Step 4

To reset, move the switch to ‘Off’ and then back to ‘Auto’. Wait

for the relay to click (5 to 10 seconds).

When the instant salt level is stable (and the negative sign still

present), slide switch to ‘Super Chlorinate’ and back to ‘Auto’.

It takes about 30 seconds for the unit to settle back on the

default reading. It should now reflect the new average salt level.

Press Diagnostics button 5 times to display the Instant Salt level.

Wait for the number to stabilize.

1600 -3200

-3200 3200

Step 2

Step 1

NOTE: Repeat this process once more to ensure both polarities are reading within 500ppm of each other.

Inhaltsverzeichnis

Andere Hayward Beleuchtungsausrüstung Handbücher

Hayward

Hayward Goldline Controls Sense and Dispense Total Pool Chemistry... Bedienungsanleitung

Hayward

Hayward CL100 Bedienungsanleitung

Hayward

Hayward OmniLogic Bedienungsanleitung

Hayward

Hayward Sheer 500 Bedienungsanleitung

Hayward

Hayward ColorLogic WFBCUS1100 Bedienungsanleitung

Hayward

Hayward ProLogic Bedienungsanleitung

Hayward

Hayward Pool pH Bedienungsanleitung

Hayward

Hayward Jiffy Niche Bedienungsanleitung

Hayward

Hayward KingRay Bedienungsanleitung

Hayward

Hayward S311SX Bedienungsanleitung

Hayward

Hayward OnCommand Bedienungsanleitung

Hayward

Hayward Stainless Steel Niches Bedienungsanleitung

Hayward

Hayward Pro Logic Bedienungsanleitung

Hayward

Hayward AQL-CHEM Bedienungsanleitung

Hayward

Hayward WFBRNDBRS Bedienungsanleitung

Hayward

Hayward Salt & Swim Bedienungsanleitung

Hayward

Hayward AQL-CHEM4-ACID Bedienungsanleitung

Hayward

Hayward Pro Logic Bedienungsanleitung

Hayward

Hayward Turbo Cell Bedienungsanleitung

Hayward

Hayward AquaRite+ AU Master Handbuch

Hayward

Hayward ProLogic Bedienungsanleitung

Hayward

Hayward Control Station Bedienungsanleitung

Hayward

Hayward ASL C1250 Bedienungsanleitung

Hayward

Hayward SP1091LX Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung