Hayward ColorLogic WFBCUS1100 Bedienungsanleitung

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

Hayward Pool Products

620 Division Street, Elizabeth NJ 07207

Phone (908)-355-7995

www.hayward.com

ColorLogic Bubbler

Owner’s Manual

092619 RevA beta draft1

WFBCUS1100

WFB100

Contents

BeforeYouBegin......................................2

Installation..............................................5

Operation..............................................12

Winterization.........................................12

Warranty................................................18

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

IMPORTANT SAFETY INSTRUCTIONS

When using this electrical equipment, basic safety precautions should always be followed, includ-

ing the following:

READ AND FOLLOW ALL INSTRUCTIONS

WARNING - Read and follow all instructions in this owner’s manual and on the equip-

ment. Failure to follow instructions can cause severe injury and/or death.

WARNING – ELECTRIC SHOCK HAZARD. MOUNTING A LUMINAIRE THAT REQUIRES

BONDING OR GROUNDING IN THIS NICHE CAN CAUSE SEVERE INJURY AND/OR DEATH. DO

NOT MOUNT NON-UL LISTED LIGHTS OR ANY LUMINAIRE THAT REQUIRES BONDING OR

GROUNDING IN THIS NICHE.

WARNING – Risk of Electric Shock. Hazardous voltage can shock, burn, and cause

death or serious property damage. All electrical wiring MUST be in conformance with ap-

plicable local codes, regulations, and the National Electrical Code (NEC). To reduce the risk

of electric shock, do NOT use an extension cord to connect unit to electric supply. Provide a

properly located electrical receptacle. Before working on any electrical equipment, turn off

power supply to the equipment.

WARNING – Risk of Electric Shock. Opening light can cause shock, burn and severe

injury. Light has no user serviceable parts inside. Do not open light.

NOTICE – This swimming pool product is UL listed for permanently installed pools or

spas only. It is not listed for storable pools or spas. Permanently installed pools and spas

are those constructed in or partially in the ground and all others capable of holding water in

a depth greater than 42 in (1.07 m). Storable pools and spas are those constructed on or

above the ground and capable of holding water to a maximum of 42 in (1.07 m).

WARNING – Electrical shock hazard. Damage to wiring can cause severe injury or

death. To reduce the risk of electric shock replace damaged wiring immediately. Locate

conduit to prevent abuse from lawn mowers, hedge trimmers and other equipment.

SAVE THESE INSTRUCTIONS

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

Before You Begin

The Hayward WFB100 ColorLogic®Bubbler has been designed for use with all Hayward Accent

Lights and provides lighted water for small fountains and other water effects. The ColorLogic®

Bubbler must be installed as speciﬁed by these instructions. Please follow ALL of the instructions

enclosed with this unit. It is recommended to keep the unit in its original packaging until the site is

prepared for installation.

Compatibility

The Hayward WFB100 ColorLogic®Bubbler is compatible with the following Hayward Accent Light

models:

Hayward ColorLogic®320

Hayward ColorLogic®160

Hayward ColorLogic®320 Network

Hayward ColorLogic®160 Network

Hayward CrystaLogic®320

Hayward CrystaLogic®160

Note that the WFBCUS1100 version comes packaged with one ColorLogic®320 Accent Light with

a 100’ cord.

What’s Included

Refer to the image and the table on the following page for a list of all items included with the

Hayward WFB100 ColorLogic®Bubbler.

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

ITEM NO. QTY.

PART NUMBER DESCRIPTION

10*

11*

12*

13*

G1-046397

G1-068159

SP1022C

G1-046400

G1-046399

G1-046398

G1-046393

G1-046395

G1-046396

G1-046394

G1-046403

SP0710XZ3

Cardboard Pipe Spacer

Housing

Gunite Shield

1-1/2” Threaded Plug with O-Ring

Plaster Shield

Plaster Ring

Lens

Retaining Ring

ColorLogic Bubbler Nozzle, 1/2”

ColorLogic Bubbler Nozzle, 3/4”

ColorLogic Bubbler Nozzle Nut

ColorLogic Bubbler Nozzle Threaded Plug

Plaster Shield O-Ring (For Winterization Only)

14* SP1022CZ2 O-Ring For Nozzle and Plug 2

*Comes In Plastic Bag

15* G1-046401 ColorLogic Bubbler Tool 1

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

Exploded View

**Plaster Ring only adjustable during Installation.

8. Retaining

Ring

7. Lens

11. Nozzle Nut

9-10. Adjustable

Nozzle (1/2” or

3/4”)

Accent Light

(included with

WFBCUS1100)

2. Housing

1. Cardboard Spacer

1.5” SCHED

40 Electrical

Conduit (Not

Included)

1.5” SCHED 40

PVC Pipe (Not

Included)

6. Plaster Ring**

14. O-Ring

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

Installation

System Overview

The diagram below shows an overview of a fully installed ColorLogic Bubbler system.

**Hayward recommends mounting the ColorLogic®Bubbler no more than 12” below the surface of

the water when installed as a bubbler/fountain for the best combination of water and light.

Determine the location for the ColorLogic®Bubbler. Rough-in plumbing pipe and electrical conduit

by plumbing the water line to the desired pumping system and the electrical line to the Accent

Light junction box as shown above. It is recommended that you use 1.5” SCHED 40 Electrical Con-

duit for the electrical line. Use the two provided cardboard pipe spacers to ensure proper distance

from the plumbing and electrical pipes (as shown on page 7). Keep the cardboard pipe spacers on

the pipes to make installation of the housing easier later on. If you have lost or discarded the pipe

spacers, note that the distance between the centers of each pipe should be exactly 2.5”.

NOTE: If ﬁnite control will be desired, be sure to install an in-line ﬂow control valve to adjust the

height and ﬂow of the water stream from the ColorLogic®Bubbler.

FLOWLIGHT

Accent Light

Adjustable Nozzle

(1/2” or 3/4”)

From 12V Input

Junction Box

From Pool or Spa Water Supply +

optional in-line ﬂow control valve

Plaster

Gunite

Dirt/Gravel

2-12” **

1.5” SCHED 40

Electrical Conduit

1.5” SCHED 40

PVC Pipe

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

Installation Steps

Follow the steps below to ensure proper installation of the ColorLogic Bubbler.

1. Cut the two pieces of 1.5” pipe to no less than 2” beneath the surface level to ensure proper

ﬁnal installation height. The pipes should also be at least 14” in height to accomodate for the

length of the accent light that will be used (if lighting is desired). If lighting will not be used, it

is recommended that you still leave enough room in case a future upgrade is desired. See the

image below for reference.

2”

14”

Plaster

Gunite

Dirt/Gravel

1.5” SCHED

40 Electrical

Conduit

1.5” SCHED

40 PVC Pipe

Use the looped plumbing scheme below if multiple

bubblers will be installed at the same depth.

Use the plumbing scheme below with individual

valves if bubblers will be installed at different depths.

From Pool or Spa Water Supply From Pool or Spa Water Supply

Valve

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

2. Remove the following parts from the box: Housing, Gunite Shield, and 2 Threaded Plugs.

These parts come assembled together as shown below. DO NOT DISASSEMBLE.

3. Verify that the cardboard spacers are on the 2 pipes to ensure proper distance between them

(as seen below). If the spacers are not on the pipes, put them on now to make the next step

easier.

4. Glue the housing assembly to the two pipes as shown below. Note that the ports are revers-

ible so it does not matter which one is used for the electrical line or the plumbing line. Verify

that the housing is fully installed to ensure ﬂush installation to the surface level. Remove the

cardboard spacers by tearing them off by hand or with a utility knife.

5. Backﬁll the pit beneath the housing with dirt and/or gravel to about halfway up the pipes. The

System Overview diagram on page 5 shows the approximate level that the dirt/gravel should

be at.

Pipe Flush With Housing

Cardboard

Pipe Spacer

Plumbing Line

Electrical Line

2.5”

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

6. Apply gunite and ﬁll behind the housing up to the level shown in the System Overview dia-

gram on page 5 and below.

7. Wait for the gunite to cure. Once cured, remove the 2 threaded plugs and the gunite shield

from the housing assembly. Discard the gunite shield but save the plugs in case of future

maintenance.

8. Remove the following parts from the box: the plaster ring and the plaster shield. These parts

come assembled together as shown below. DO NOT DISASSEMBLE. IMPORTANT: No

o-ring is to be installed with the plaster shield; this is for winterization purposes only

(See page 12 for winterization instructions).

Threaded Plugs

Gunite Shield

Housing Assembly

glued to pipes

After Gunite applied

Gunite up to this line

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

9. Install the plaster shield assembly onto the housing and verify that the surface of the plaster

shield is level with the ﬁnished surface. If the housing was not installed level in step 4, use

the plaster ring to achieve a level ﬁnished surface by pulling up on the edge of the plaster ring

until level. See images below for reference.

10. Apply and smooth out plaster around the edge of the plaster shield as seen below. The

surface of the plaster should be even with the ﬁnished surface level.

Plaster up to this line

Plaster Shield and

Plaster Ring

Gunite Surface

After Plaster

Applied

Finished Surface Finished Surface

Flush Housing Installation

Plaster

Gunite

Housing Installed at a 2° angle

Pull up on Plaster Ring

To achieve level ﬁnished

surface

Plaster

Gunite

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Hayward Beleuchtungsausrüstung Handbücher

Hayward

Hayward OmniLogic Bedienungsanleitung

Hayward

Hayward Aqua Rite® Pro Bedienungsanleitung

Hayward

Hayward CL220BR series Bedienungsanleitung

Hayward

Hayward AquaRite+ AU Master Handbuch

Hayward

Hayward GOLDLINE Aqua Rite Pro LS Bedienungsanleitung

Hayward

Hayward OnCommand Bedienungsanleitung

Hayward

Hayward OmniLogic Bedienungsanleitung

Hayward

Hayward CL100 Bedienungsanleitung

Hayward

Hayward ProLogic Bedienungsanleitung

Hayward

Hayward Pro Logic Bedienungsanleitung

Hayward

Hayward AQL-CHEM Bedienungsanleitung

Hayward

Hayward AquaRite series Bedienungsanleitung

Hayward

Hayward AquaRite AQR15 Bedienungsanleitung

Hayward

Hayward TriStar VS 900 Omni Bedienungsanleitung

Hayward

Hayward S311SX Bedienungsanleitung

Hayward

Hayward Sense and Dispense Bedienungsanleitung

Hayward

Hayward VR1000 Bedienungsanleitung

Hayward

Hayward ASL C1250 Bedienungsanleitung

Hayward

Hayward SwimPure Plus Technisches Datenblatt

Hayward

Hayward Goldline Controls Aqua Logic AQL-P-4 Bedienungsanleitung

Hayward

Hayward Jiffy Niche Bedienungsanleitung

Hayward

Hayward OmniPL HLBPRO4SW Bedienungsanleitung

Hayward

Hayward Vistapool Handbuch

Hayward

Hayward XStream CC1000 Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung