Hayward Sheer 500 Bedienungsanleitung

Hayward Industries

400 Connell Drive, Suite 6100

Berkeley Heights, NJ 07922

Phone: (908) 355-7995

www.hayward.com

Sheer 500 (LED)

Water Feature With LED Lighting

Owner's Manual

Contents

Introduction............................2

Installation.............................2

Mechanical.............................3

Plumbing................................5

ELectrical Wiring.....................6

Operation..............................10

Maintenance.........................13

Replacement Parts................13

Warranty................................14

1001811 RevA

WFS512B6LED WFS548B6LED

WFS518B6LED WFS560B6LED

WFS524B6LED WFS572B6LED

WFS536B6LED WFS584B6LED

LFCUS11100

LFCUS11150

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

IMPORTANT SAFETY INSTRUCTIONS

When using this electrical equipment, basic safety precautions should always be followed, including

the following:

READ AND FOLLOW ALL INSTRUCTIONS

WARNING - Read and follow all instructions in this owner’s manual and on the equip-

ment. Failure to follow instructions can cause severe injury and/or death.

WARNING - ELECTRIC SHOCK HAZARD. MOUNTING A LUMINAIRE THAT REQUIRES

BONDING OR GROUNDING IN THIS NICHE CAN CAUSE SEVERE INJURY AND/OR DEATH.

DO NOT MOUNT NON-UL LISTED LIGHTS OR ANY LUMINAIRE THAT REQUIRES BONDING

OR GROUNDING IN THIS NICHE.

WARNING - Risk of Electric Shock. Hazardous voltage can shock, burn, and cause

death or serious property damage. All electrical wiring MUST be in conformance with ap-

plicable local codes, regulations, and the National Electrical Code (NEC). To reduce the risk

of electric shock, do NOT use an extension cord to connect unit to electric supply. Provide

a properly located electrical receptacle. Before working on any electrical equipment, turn

off power supply to the equipment.

WARNING - Risk of Electric Shock. Opening light can cause shock, burn and severe

injury. Light has no user serviceable parts inside. Do not open light.

NOTICE - This swimming pool product is UL listed for permanently installed pools or

spas only. It is not listed for storable pools or spas. Permanently installed pools and spas

are those constructed in or partially in the ground and all others capable of holding water

in a depth greater than 42 in (1.07 m). Storable pools and spas are those constructed on

or above the ground and capable of holding water to a maximum of 42 in (1.07 m).

WARNING - Electrical shock hazard. Damage to wiring can cause severe injury or

death. To reduce the risk of electric shock replace damaged wiring immediately. Locate

conduit to prevent abuse from lawn mowers, hedge trimmers and other equipment.

SAVE THESE INSTRUCTIONS

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

Introduction

The Hayward Sheer 500 water feature and LED light combination is designed to enhance your back-

yard pool or spa experience with stunning lighting effects and soothing sounds of falling water. The

Sheer 500 must be installed as speciﬁed by these instructions. Please follow ALL of the instructions

enclosed with this unit. It is recommended to keep the unit in its original packaging until the site is

prepared for installation.

What's Included

Refer to the table below for a list of all items included with the Hayward Sheer 500.

Included

Item # Part Description Quantity

1Waterfall Assembly 1

2 LED Light Installation Tool 1

3Extractor Tool 1

4 Lid, Collar & Ext. Collar Set (Tan) 1

Installation

Preparation

Installation of the Waterfall requires the use of:

• Pump

• Cartridge ﬁlter (Do NOT use sand or DE ﬁlter)

• Flow control valve

• Low voltage transformer and (optional) single gang junction box

• LED Light control system (wall switch or automation control)

• PVC Pipe and 1 in. electrical conduit (refer to table below)

Waterfall Length Supply Pipe Size

Less than 18 in. 1½ in.

18 in. - 4 ft 2 in.

Greater than 4 ft 3 in.

NOTE: 2 in. plumbing is required for installations using optional rock trap (heavy debris installations).

Sold Separately

Item # Part Description Quantity

1 LED Light Assembly 100' 1

2 LED Light Assembly 150' 2

3 Black Lid & Collar Set 1

4 White Lid & Collar Set 1

5 Dark Grey Lid & Collar Set 1

6 Grey Lid & Collar Set 1

7Rock Trap 1

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

Determine the install location(s) for the Waterfall. Be sure to follow all NEC and local codes during

installation. To achieve the proper water effect, it is recommended to install the Waterfall no higher

than 3 feet above water level. The maximum cable run from the LED light to the low voltage trans-

former should not exceed 150 feet.

Mechanical

Refer to the diagram below for Waterfall dimensions before roughing-in plumbing and electrical

lines. Note that the length of the waterfall (not shown) varies depending on model.

Step 1: Rough-in plumbing and electrical lines. See overview diagram on page 5.

Step 2: Cut a notch in the bond beam and attach a board as shown below. Make sure the board

is level as it will be used for setting the level of the waterfall.

14.00"

8.09"

4.16"

2.08"

9.84"

4.47"

}0.61"

1.85"

Position the board

0.625" below the top

of the bond beam. The

edge of the Waterfall

lip will rest on the top

of the board.

Length of Waterfall + 2"

USE ONLY HAYWARD GENUINE REPLACEMENT PARTSUSE ONLY HAYWARD GENUINE REPLACEMENT PARTS

Step 3: Fill the notch with mortar and set the Waterfall in the mortar as shown below. Make sure

that the lip support is in place to prevent debris from getting in the Waterfall. Note that the

edge of the Waterfall lip should clear the ﬁnished tile line by ¾". The lip should be level on

the board and fully supported by the mortar.

Step 4: Wait for the mortar to fully cure and then remove the board.

Step 5: Glue the ext. deck lid collar onto the waterfall unit with PVC glue. If the Waterfall is installed

in a raised wall, a 3" PVC pipe can be used to extend the distance between the top of the

Waterfall unit and the deck surface, allowing access to the LED light.

8" Bond Beam

Board

Mortar Bed

Lip Support

Waterfall

Assembly

3" PVC Extension Pipe

Ext. Deck Lid Collar

Deck Lid Cover

Water Line Water LineElectrical Line

Waterfall Front View

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

Step 6: Glue the Waterfall to the water lines and electrical line.

Step 7: Install the coping and tile ﬁnish. Note that it may be necessary to add ﬁller on top to level

out the top of the Waterfall lip with the top of the bond beam.

Step 8: Once installation is complete, the Waterfall lip support can be removed.

Plumbing

Refer to the diagram below for a basic installation overview. If plumbing multiple Waterfalls in-line,

use a looped plumbing conﬁguration as shown on the next page.

Refer to page 2 when determining the pipe size for the water supply line. Note that when using the

optional rock trap (not pictured above), 2" plumbing is required.

The Waterfall requires a cartridge ﬁlter to be plumbed in the water supply line, otherwise debris that

gets in the system could damage the Waterfall. Do NOT use a sand or DE ﬁlter.

It is recommended to plumb a ﬂow control valve in the water supply line in order to control the ﬂow

of water to the Waterfall and achieve the desired water effect. If using a variable speed pump, then

a ﬂow control valve may not be needed.

From High

Voltage

Supply

Flow Control

Valve

Cartridge

Filter

From

Pump

Low Voltage

Transformer

Hayward

LJBUY00PP1

Junction Box

Water Supply Line to Waterfall(s).

See Looped Plumbing diagram

if plumbing mutiple Waterfalls

together.

Electrical Line

Water Level

Deck Lid

Coping

Up to 3'

Recommended

Mortar

Bed

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

Looped Plumbing

When plumbing multiple Waterfall systems together, a looped plumbing method as shown below

should be used. This will ensure that pressure to all Waterfalls is equalized and they will all have the

same water effect.

Electrical Wiring

Refer to the wiring overview diagram below and the following pages for wiring steps.

Hayward

LJBUY00PP1

Junction Box

High Voltage from

Manual Wall Switch

Automation Control Relay

Low Voltage

Transformer

LED Light

Deck Lid

Collar & Cover

IMPORTANT: Transformer/junction box MUST

be installed above the highest water level in the

Waterfall system to prevent water from ﬁlling

the transformer/junction box.

Total distance of cable between LED Light

and Transformer should not exceed 150 feet.

Note: Only 5'

to 8' models

have multiple

water ports.

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

The Waterfall's LED Light requires the use of a low voltage transformer (not included). See chart

below to determine the type of transformer you will need based on the number of LED Lights used.

When considering the number of transformers required, note that one LED Light is 25W and the load

on a transformer should not exceed 80% of the maximum wattage.

Number of Lights Type of Transformer

1-2 70W

3-9 300W

10+ Multiple Transformers

NOTE: Any lights wired to the same transformer will run together. If independent operation is

desired, then each light or group of lights will require their own separate transformer.

Step 1: Running the Cable

With the Waterfall unit now installed, it is time to run the wiring cable from the LED light to the junc-

tion box or low voltage transformer. Note that the maximum cable length between the Waterfall and

the low voltage transformer should not exceed 150 feet. Cable runs that are 100 feet or less should

use 14 gauge wire and more than 100 feet should use 12 gauge wire. Feed the cable through the

electrical line from the Waterfall to the junction box or transformer. At the junction box or transformer,

cut the extra cord leaving enough for wiring.

If using an optional junction box - run the cable from the junction box to the low voltage transformer.

Cut the extra cord at both the junction box and the transformer leaving enough for wiring.

Verify that all power is off and then run the cable from the power source – either a manual wall

switch or an automation control relay – to the low voltage transformer. Cut the extra cord at both

ends leaving enough for wiring.

Step 2: Junction Box Wiring (optional)

A junction box is useful if multiple Waterfall LED Lights will be wired together. To make connections

easier, it is recommended to use Wago 221 Series lever nuts (pictured below) but standard electrical

wire nuts can also be used.

To LED Light From Transformer

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

Step 3: Low Voltage Transformer Wiring

Refer to the wiring diagram below for Hayward 300W transformers. For other transformers, refer to

the instructions. Be sure to follow all NEC and local codes when wiring.

From power control To junction box / LED light

Bonding

Wire

L1 & L2 low voltage

connections

Neutral

Connection

(white)

Hot

Connection

(black)

Ground

(green)

Use 14V tap

(blue)

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

Step 4: Power Control Wiring

When wiring to a wall switch or automation control, follow the directions in the manual provided

with that product. When wiring to a Hayward Omni control relay or an Omni Smart Relay, refer to the

graphics below. Be sure to follow all NEC and local codes when wiring.

Hot (black)

Connection to transformer

Neutral (white)

Connection to transformer

Ground (green)

Connection to transformer

Omni Standard Relay Wiring

Omni Smart Relay Wiring

Neutral Line 1 in

Load 1 out Neutral

Black/White

Black

Red

Red/White

Gray

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

Inhaltsverzeichnis

Andere Hayward Beleuchtungsausrüstung Handbücher

Hayward

Hayward VR1000 Bedienungsanleitung

Hayward

Hayward Salt & Swim Datenblatt

Hayward

Hayward Pool pH Bedienungsanleitung

Hayward

Hayward HL32950VVSP Bedienungsanleitung

Hayward

Hayward OnCommand Bedienungsanleitung

Hayward

Hayward WFBRNDBRS Bedienungsanleitung

Hayward

Hayward WFL100 ColorLogic Bedienungsanleitung

Hayward

Hayward Aqua Rite® Pro Bedienungsanleitung

Hayward

Hayward Vistapool Handbuch

Hayward

Hayward AquaRite AQR15 Bedienungsanleitung

Hayward

Hayward OmniPL HLBPRO4SW Bedienungsanleitung

Hayward

Hayward TriStar VS 900 Omni Bedienungsanleitung

Hayward

Hayward SwimPure Plus Technisches Datenblatt

Hayward

Hayward Goldline Controls Sense and Dispense Total Pool Chemistry... Bedienungsanleitung

Hayward

Hayward ProLogic Bedienungsanleitung

Hayward

Hayward ASL C1250 Bedienungsanleitung

Hayward

Hayward CL100 Bedienungsanleitung

Hayward

Hayward Pro Logic Bedienungsanleitung

Hayward

Hayward ProLogic Bedienungsanleitung

Hayward

Hayward EasyClear C550 Bedienungsanleitung

Hayward

Hayward SwimPure Bedienungsanleitung

Hayward

Hayward AquaRite+ AU Master Handbuch

Hayward

Hayward Control Station Bedienungsanleitung

Hayward

Hayward OmniHub Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung