Honeywell BW Icon Bedienungsanleitung

USER

MANUAL

M05-4002-001 Rev-A ENG ©July 14, 2020

Honeywell BW ™ Icon &BW ™ Icon +

Portable Multiple Gas Detector

TOC

Introduction 5

Product Description 5

Safety 5

Standards and Certifications 6

What's in the Box 7

Overview 7

Operations 9

Activate the Detector 9

Self Test 9

Deactivate the Detector 9

Common Button Operations 10

Bluetooth Pairing 10

Calibration 10

Bump Test 13

Capture Real Time Reading 16

Set the Detector via Device Configurator 16

Maintenance 17

Charge the Battery 17

Firmware Update 20

Additional Information 21

Sensor Poisons and Contaminants 21

Sensor Specifications 22

General Specifications 23

Time Out Events 24

Troubleshooting 24

DataLogs and Event Logs 27

Alarms 28

BW Icon 2 User Manual

Certified Labels 29

Replacement Parts 30

Security Information 31

BW Icon 3 User Manual

CHAPTER

1Introduction

Learn what you need to know about the Honeywell BW™ Icon Gas Detector before operating.

Product Description

The Honeywell BW™ Icon & Honeywell BW™ Icon+ gas detectors warns of hazardous gas at levels

above user-defined alarm setpoints. The detector can monitor up to four gases at a time.

Safety

CAUTION

• The detector is a personal safety device. It is your responsibility to respond properly to

the alarm.

• For safety reasons, this equipment must be operated and serviced by qualified personnel only.

• The lithium battery in this product presents a risk of fire, explosion, and chemical burn if

misused. Do not disassemble, incinerate, or heat above 212°F (100°C). Batteries exposed to heat

at 266°F (130°C) for 10 minutes can cause fire and explosion. Batteries must only be charged in a

safe area free of hazardous gas.

• Deactivating the detector by removing the battery pack may cause improper operation and harm

the detector.

• Use only Honeywell approved battery chargers such as the vehicle Charger.

• Do not use the apparatus if it is damaged. Inspect the apparatus before use. Look for cracks and

missing parts.

BW Icon 5 User Manual

Standards and Certifications

IECEx: IECEx SIR 20.0020X

Ex ia op is I Ma Ex ia op is IIC T4 Ga, -40°C≤ Tamb ≤ 60°C (with IR sensor installed)

Ex ia I Ma Ex ia IIC T4 Ga, -40°C≤ Tamb ≤ 60°C

2813

ATEX: Sira 20ATEX2012X

I M1 Ex ia op is I Ma, -40°C ≤ Tamb ≤ 60°C (with IR sensor installed)

II 1G Ex ia op is IIC T4 Ga, -40°C ≤ Tamb ≤ 60°C (with IR sensor installed)

I M1 Ex ia I Ma, -40°C ≤ Tamb ≤ 60°C

II 1G Ex ia IIC T4 Ga, -40°C ≤ Tamb ≤ 60°C

RE-D Directive 2014/53/EU

EMC Directive 2014/30/EU

ROHS Directive (EU) 2015/863 amending 2011/65/EU

IP: IP66, IP68 (1.2 meters for 45 minutes)

Contains FCC ID: SU3RMBLED

Contains IC: 20969-RMBLED

CAN ICES-3(A)/NMB-3(A)

FCC Compliance statement

This device complies with part 15 of the FCC Rules. operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction manual, may cause harmful interference to

radio communications. Operation of this equipment in a residential area is likely to cause

harmful interference in which case the user will be required to correct the interference at his

own expense.

BW Icon 6 User Manual

What's in the Box

1 Honeywell BW™ Icon gas detector

1 Battery (factory-installed)

1 USB charger

1 Calibration cap

1 Klick Fast stud

1 Quick Reference Guide

1 Tubing

Overview

1 LED Alarm 6 Sensor

2 IntelliFlash 7 Clip

3 Display 8 Battery

4 Button 9 Charging Port

5 Beeper

BW Icon 7 User Manual

User Interface

Alarm One — Shows when alarm one is breached and gas highlighted next to

sensor

Alarm Two — Shows when alarm two is breached. Alarm two will over write any

alarm one status.

Time Weighted Average — Settable in Safety Suite DC for each toxic sensor.

Short Term Exposure Limit — Settable in Safety Suite DC for each toxic

sensor.

Bump — Shows when bump is due and you can configure to have a count

down.

Calibration — Shows when bump is due and you can configure to have a count

down.

Battery status — Shows battery status and when on charge will show charging

status.

Bluetooth — All devices have Bluetooth – double click to enter menu. for

search mode

BW Icon 8 User Manual

CHAPTER

2Operations

Learn what you can do with your Honeywell BW™ Icon Detector, from commissioning to

Calibration.

Activate the Detector

To turn the detector on, press and hold the button for four seconds. LEDs turn on, and the

detector vibrates and beeps.

Self Test

When the detector is activated, it performs several start-up tests.

lBattery

lData Flash

lRTC. Real Time Clock

lTemperature sensor.

lBLE module

lSensors

lBump and Calibration due date

When the detector has passed all the start-up self-tests, it enters the regular operation mode.

Deactivate the Detector

To turn the detector off, press and hold the button for four seconds. LEDs turn on, and the

detector beeps four times.

BW Icon 9 User Manual

Andere Handbücher für BW Icon

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Honeywell Gaswarngerät Handbücher

Honeywell

Honeywell HON COCON 13 Bedienungsanleitung

Honeywell

Honeywell SEARCHLINE EXCEL PLUS Benutzerhandbuch

Honeywell

Honeywell MultiRAE Series Bedienungsanleitung

Honeywell

Honeywell BW Ultra Bedienungsanleitung

Honeywell

Honeywell SEARCHLINE EXCEL PLUS Bedienungsanleitung

Honeywell

Honeywell BW MaxXT II Bedienungsanleitung

Honeywell

Honeywell 04230-A-1001 Versionshinweis

Honeywell

Honeywell ToxyPoint Bedienungsanleitung

Honeywell

Honeywell Searchpoint Optima Plus Benutzerhandbuch

Honeywell

Honeywell MultiRAE Bedienungsanleitung

Honeywell

Honeywell RAEGuard 3 Bedienungsanleitung

Honeywell

Honeywell JTQJ-BF-01LM/BW Bedienungsanleitung

Honeywell

Honeywell BW Ultra Bedienungsanleitung

Honeywell

Honeywell SEARCHZONE SONIK SZSK-SMG Series Bedienungsanleitung

Honeywell

Honeywell BW Technologies GasAlertQuattro 1 Bedienungsanleitung

Honeywell

Honeywell BW Technologies GasAlert Quattro Bedienungsanleitung

Honeywell

Honeywell Signalpoint Pro Bedienungsanleitung

Honeywell

Honeywell SEARCHLINE EXCEL EDGE Bedienungsanleitung

Honeywell

Honeywell SEARCHZONE SONIK Bedienungsanleitung

Honeywell

Honeywell BW GasAlertMicroClip XT Bedienungsanleitung

Honeywell

Honeywell Touchpoint Plus Bedienungsanleitung

Honeywell

Honeywell Midas Bedienungsanleitung

Honeywell

Honeywell SEARCHZONE SONIK Bedienungsanleitung

Honeywell

Honeywell BW Technologies GasAlert MicroClip XT Bedienungsanleitung

Beliebte Gaswarngerät Handbücher anderer Marken

Macurco

Macurco GD-6 Bedienungsanleitung

Evikon

Evikon E2632 Bedienungsanleitung

Critical Environment Technologies

Critical Environment Technologies CGAS-A Series Bedienungsanleitung

MSA

MSA altair 5 Bedienungsanleitung

DOD Technologies

DOD Technologies ChemLogic CL96 Bedienungsanleitung

DEGA

DEGA NS III LCD Series Bedienungsanleitung

RKI Instruments

RKI Instruments 35-3001A-08-01 Bedienungsanleitung

Sygonix

Sygonix 2483186 Bedienungsanleitung

Perry

Perry 1GA 50917MET/P Bedienungsanleitung

isweek

isweek AS8900 Bedienungsanleitung

Oldham

Oldham OLC 10 Bedienungsanleitung

Wizmart

Wizmart NB983 Bedienungsanleitung

Beacon

Beacon MEGA Handbuch

RKI

RKI GX-6000 Bedienungsanleitung

Dräger

Dräger PIR 7000 Bedienungsanleitung

GDS

GDS GASMAX EC Bedienungsanleitung

Seitron

Seitron BE COOL R1 Bedienungsanleitung

MSA

MSA ULTIMA X5000 Bedienungsanleitung