Honeywell DR Graphic Bedienungsanleitung

43-TV-33-217 iss.3 GLO Jan 2021 UK 1

DR Graphic recorder - Installation Instruction

Door Handle Kit Assembly

DR Graphic Recorder

This Installation Instruction sheet is intended as a guide for replacing or installing hardware and for setting up

functionality in the recorder. Refer to the User manual for detailed operational requirements.

The DR Graphic recorders are designed for ease of assembly with minimal disturbance to the rest of the unit. If unsure,

please return the unit to your supplier for repair or upgrade.

Opening the recorder and removing the internal chassis of the recorder should only be performed under the following

circumstances:

When an item of hardware requires individual replacement.

When an item of hardware is to be retrospectively fitted.

In all other instances it is recommended that the complete unit be returned to an authorized agent or service centre. For

Agency Approved recorders the product needs to be upgraded or repaired by an Authorized Repair facility

WARNING

HAZARDOUS VOLTAGES

Disconnect all the power, CJCs and IO cabling to the recorder before removing the IO cards chassis or power supply

chassis and attempting any maintenance procedures.

SAFETY TESTS

Upon completion of service procedures detailed in this instruction verify the installation per the installation section of the

product manual.

Failure to comply with these instructions could result in death or serious injury

CAUTION

OBSERVE ANTI-STATIC PRECAUTIONS

Refer to BS EN61340-5-1: 2001. Basic specification. Protection of electrostatic sensitive devices. Full anti-static

precautions MUST be observed when in contact with the electronics of your recorder.

SAVE DATA, SETUPS AND LAYOUTS

Removal of PCBs and battery back-up will result in the loss of all non-volatile data.

Ensure all data and set-ups are saved.

Failure to comply with these instructions may result in product damage.

43-TV-33-217 iss.3 GLO Jan 2021 UK 2

Before attempting to repair or upgrade a recorder, it is advisable to clear sufficient work space so components such as

the front panel can be rested on the work surface without getting scratched or damaged.

Replacing Old Latch Bracket

1. If the latch bracket needs replacement; remove the two screws and washers shown with black arrows. Remove the

latch pin from the right side.

2. Take the new latch bracket and put it in place, reconnect the bracket with the two screws and washers.

Removing Old Door Handle

3. For removing the door handle, remove the two hex screws using an allen wrench as shown in Figure 2.

Figure 2 —Removing both the hex nuts to remove the door handle

Figure 1

Position of latch bracket

43-TV-33-217 iss.3 GLO Jan 2021 UK 3

4. Push the door handle out by using the wrench and pull out the latch door handle by your other hand. Remove the

latch CAM and Southco spring assembly.

Fitting New Door Handle

5. Insert C shaped washer on top of the door handle. The flat surface of c shaped washer should be on the bottom

6. Insert latch spring into the stud. Make sure that the smaller radius end of the spring is facing stud head.

Figure 5

Latch spring and stud

Figure 4

Adding C shaped washer

Figure 3 —Removing both the hex nuts

43-TV-33-217 iss.3 GLO Jan 2021 UK 4

7. Insert stud with latch spring into the door handle. See Figure 6.

8. Insert the washer on the stud from the other side to hold the stud in place and insert the white washer onto the latch

handle as shown in Figure 7.

9. Put the Southco spring on to the latch CAM as shown in Figure 8.

10. Insert the Latch CAM and Southco Spring assembly back into the bezel slot.

See Figure 9.

Figure 6

Adding stud to handle

Figure 7

Holding stud in place

with washer

Figure 8

Adding Southco spring

Figure 9

Position of Latch CAM and

Southco Spring assembly

43-TV-33-217 iss.3 GLO Jan 2021 UK 5

11. Hold the latch cam by one hand and insert the door handle back into the door handle hole by other hand.

See Figure 10.

12. Reconnect the two hex screws using the allen wrench.

13. Assembly is complete, close the door of the recorder.

Copyrighted Materials. For more information please contact your supplier.

Figure 10

Adding latch handle

Figure 11

Reconnecting

hex screws

Andere Handbücher für DR Graphic

Inhaltsverzeichnis

Andere Honeywell Messgerät Handbücher

Honeywell

Honeywell SmartLine RMA800 Bedienungsanleitung

Honeywell

Honeywell HEN04112 Bedienungsanleitung

Honeywell

Honeywell eZtrend GR Series Bedienungsanleitung

Honeywell

Honeywell Vertex M Versionshinweis

Honeywell

Honeywell BK-G1.6A Bedienungsanleitung

Honeywell

Honeywell MiniRAE 3000+ Bedienungsanleitung

Honeywell

Honeywell SLN 700 Bedienungsanleitung

Honeywell

Honeywell Sensepoint XCD RTD Bedienungsanleitung

Honeywell

Honeywell Satellite XT 9602-0200 4-20 mA Bedienungsanleitung

Honeywell

Honeywell Sensepoint XCL Bedienungsanleitung

Honeywell

Honeywell Q340A Bedienungsanleitung

Honeywell

Honeywell TC809EA1035 Bedienungsanleitung

Honeywell

Honeywell VERSAFLOW SONIC 1000/TWS 9000 Bedienungsanleitung

Honeywell

Honeywell QA 10 DN 25 G I Bedienungsanleitung

Honeywell

Honeywell FE260 Bedienungsanleitung

Honeywell

Honeywell RM640 Bedienungsanleitung

Honeywell

Honeywell HEN04112 Bedienungsanleitung

Honeywell

Honeywell HPB Bedienungsanleitung

Honeywell

Honeywell KA 54 Bedienungsanleitung

Honeywell

Honeywell Vertex Edge Bedienungsanleitung

Honeywell

Honeywell Limitless WPMM Series Bedienungsanleitung

Honeywell

Honeywell enCore Series Bedienungsanleitung

Honeywell

Honeywell X4 Series Gebrauchsanweisung

Honeywell

Honeywell DPR180 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung