Honeywell EZtrend GR Series Bedienungsanleitung

43-TV-33-81 iss.2 GLO Aug 19 UK 1

eZtrend GR and X Series QXe recorders -

Installation Instruction

Expansion Board

QXe Recorder eZtrend Recorder

This Installation Instruction sheet is intended as a guide for replacing or installing hardware and for setting up

functionality in the recorder. Refer to the User manual for detailed operational requirements.

The eZtrend Gr and QXe recorders are designed for ease of assembly with minimal disturbance to the rest of the unit. If

unsure, please return the unit to your supplier for repair or upgrade.

Removing the case and opening the back of the recorder should only be performed under the following circumstances:

When an item of hardware requires individual replacement.

When an item of hardware is to be retrospectively fitted.

In all other instances it is recommended that the complete unit be returned to an authorised agent or service centre.

For Agency Approved recorders the product needs to be upgraded or repaired by an Authorized Repair facility.

WARNING

HAZARDOUS VOLTAGES

Disconnect all power to the recorder before removing the case and attempting any maintenance procedures.

SAFETY TESTS

Upon completion of service procedures detailed in this manual two basic safety tests should be performed in order to

ensure continued safe operation of the instrument.

Earth Resistance; 25 VDC applied between case and protective earth, bonding resistance should be < 0.1 Ohm.

Insulation Resistance; 500Vdc applied between the earth terminal, and the live and neutral terminal shorted together,

insulation resistance to be >2.0 MOhm. (Mega Ohm, NOT milli Ohm)

Failure to comply with these instructions could result in death or serious injury

CAUTION

OBSERVE ANTI-STATIC PRECAUTIONS

Refer to BS EN61340-5-1: 2001. Basic specification. Protection of electrostatic sensitive devices.

Full anti-static precautions MUST be observed when in contact with the electronics of your recorder.

SAVE DATA, SETUPS AND LAYOUTS

Removal of PCBs and battery back-up will result in the loss of all non-volatile data.

Ensure all data and set-ups are saved.

Failure to comply with these instructions may result in product damage.

43-TV-33-81 iss.2 GLO Aug 19 UK 2

Before attempting to repair or upgrade a recorder, it is advisable to clear a sufficient work space so components such as

the front panel can be rested on the work surface without getting scratched or damaged.

Panel Mounting

To replace or fit the Expansion Board the recorder must be removed from the panel. To require the recorder from the

panel, loosen the mounting clamp screws, slide the clamp towards the rear of the recorder and remove the clamps and

the recorder.

Removing the Case

Removal of the entire case is necessary for replacement or fitment of the Expansion Board.

Remove any connectors fitted in the rear of the recorder, including. The case and back panel can be removed as one

assembly.

Remove the 4 screws (2 on each side of the case). Retain screws for re-fitting.

Slide the entire case off the back of the recorder.

Figure 1

QXe recorder

Remove 2

screws each

side

43-TV-33-81 iss.2 GLO Aug 19 UK 3

Removal and re-fitting the Expansion Board

If the recorder already has an expansion board fitted, loosen the screws that hold all the I/O boards into the case. Pull

each of these cards towards the rear of the recorder so that their connectors disengage from the Expansion Board. (The

Expansion board stands vertically inside the recorder). The boards do not need to be completely removed to allow

access to the Expansion Board.

Disconnect the power supply cable from the power supply module.

Once all cards have been disengaged the Expansion Board can be pulled upwards to unplug from the processor board.

The Expansion Board can now be removed.

When boards are

disengaged, pull

Expansion Board up

Disconnect

power

supply lead

Loosen screw and

withdraw cards

Fig 2

Fig 3

43-TV-33-81 iss.2 GLO Aug 19 UK 4

Inserting a Expansion Board

Inserting a new or replacement Expansion Board is simply the reverse operation.

Drop the new Expansion Board into the board guides and push it down until it is fully plugged into the processor

board.

Carefully slide all the boards back into the recorder ensuring that the connectors mate correctly with the

Expansion Board.

Tighten the screws that retain the boards.

Plug the power supply lead back into the power supply module.

Slide the case back over the recorder assembly, ensuring that the rear connectors are aligned with the slots in

the rear panel.

Refit the 4 screws that fix the case to the recorder.

eZtrend Gr and QXe recorders torque setting should be 0.5 - 0.75Nm/4.4 - 6.6lbf-in

Copyrighted Materials. For more information please contact your supplier.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Honeywell Messgerät Handbücher

Honeywell

Honeywell MiniRAE 3000+ Bedienungsanleitung

Honeywell

Honeywell MA-1000 Bedienungsanleitung

Honeywell

Honeywell 854 ATG Series Bedienungsanleitung

Honeywell

Honeywell E-Mon KWH Bedienungsanleitung

Honeywell

Honeywell E-Mon Anleitung zur Verwendung

Honeywell

Honeywell EWA600C-RF55C Bedienungsanleitung

Honeywell

Honeywell DVC100 (M) MK2 Bedienungsanleitung

Honeywell

Honeywell Limitless WPMM Series Bedienungsanleitung

Honeywell

Honeywell SmartLine RM60 Bedienungsanleitung

Honeywell

Honeywell Green Class meter Bedienungsanleitung

Honeywell

Honeywell Enraf 854 ATG Bedienungsanleitung

Honeywell

Honeywell RMA300-ME Bedienungsanleitung

Honeywell

Honeywell Minitrend Bedienungsanleitung

Honeywell

Honeywell 90DM4 Bedienungsanleitung

Honeywell

Honeywell DR 4300 Leitfaden

Honeywell

Honeywell FS20X Series Bedienungsanleitung

Honeywell

Honeywell HEN04112 Bedienungsanleitung

Honeywell

Honeywell VERSAFLOW VORTEX 200 Verdrahtungsschema

Honeywell

Honeywell Vertex M Versionshinweis

Honeywell

Honeywell 6108 Anleitung zur Verwendung

Honeywell

Honeywell HG4930 Bedienungsanleitung

Honeywell

Honeywell HERMetic UTImeter Gtex Chem Bedienungsanleitung

Honeywell

Honeywell Touchpoint Plus Bedienungsanleitung

Honeywell

Honeywell MicroMAX Pro Betriebsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung

Honeywell eZtrend GR Series Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken