Honeywell QX Series Bedienungsanleitung

QX Recorders - Installation Instruction

Portable Case

QX Recorder

This Installation Instruction sheet is intended as a guide for replacing or installing hardware and for setting up

functionality in the recorder. Refer to the User manual for detailed operational requirements.

The QX recorders are designed for ease of assembly with minimal disturbance to the rest of the unit. If unsure, please

return the unit to your supplier for repair or upgrade.

Removing the case and opening the back of the recorder should only be performed under the following circumstances:

When an item of hardware requires individual replacement.

When an item of hardware is to be retrospectively fitted.

In all other instances it is recommended that the complete unit be returned to an authorised agent or service centre.

For Agency Approved recorders the product needs to be upgraded or repaired by an Authorized Repair facility

WARNING

HAZARDOUS VOLTAGES

Disconnect all power to the recorder before removing the case and attempting any maintenance procedures.

SAFETY TESTS

Upon completion of service procedures detailed in this manual two basic safety tests should be performed in order to

ensure continued safe operation of the instrument.

Earth Resistance; 25 VDC applied between case and protective earth, bonding resistance should be < 0.1 Ohm.

Insulation Resistance; 500Vdc applied between the earth terminal, and the live and neutral terminal shorted together,

insulation resistance to be >2.0 MOhm. (Mega Ohm, NOT milli Ohm)

Failure to comply with these instructions could result in death or serious injury

CAUTION

OBSERVE ANTI-STATIC PRECAUTIONS

Refer to BS EN61340-5-1: 2001. Basic specification. Protection of electrostatic sensitive devices.

Full anti-static precautions MUST be observed when in contact with the electronics of your recorder.

SAVE DATA, SETUPS AND LAYOUTS

Removal of PCBs and battery back-up will result in the loss of all non-volatile data.

Ensure all data and set-ups are saved.

Failure to comply with these instructions may result in product damage.

43-TV-33-62 iss.1 GLO Oct 06 UK 1

Before attempting to repair or upgrade a recorder, it is advisable to clear a sufficient work space so components such as

the front panel can be rested on the work surface without getting scratched or damaged.

Fitting the Portable case

Unpack the portable case kit and check all the parts are present. See fig 1

Terminal

cover

New

Case

43-TV-33-62 iss.1 GLO Oct 06 UK 2

Fig 1

M3x6

screws

Handle fixing

covers (2)

Handle

fixings

(2)

Handle

(inner and

cover

)

Rubber

feet

Handle fixing

screws (2) Handle fixing

nuts (2)

Slide the metal handle inner into the black plastic cover.

Place the case down as shown in Fig 1 with the ventilation slots uppermost. The handle fixes to the 2 holes along the

centre of the case.

Place one of the handle fixings on one end of the handle. Place it on the case and align the holes. See fig 2

Fig 2

Place one of the handle fixing screws through the fixing, through the handle and through the case.

On the inside of the case fit one of the handle fixing nuts (with integral washer). Leave nut loose.

Fix the other end of the handle in the same way.

When both ends are fixed tighten the nuts until the screw thread is flush with the back of the nut.

Fig 3

43-TV-33-62 iss.1 GLO Oct 06 UK 3

Fit the handle fixings covers. These cover the screws.

Fit as shown in figs 4 and 5 below.

Fig 5

Fig 4

Clip cover under

front edge Push cover down

to clip in place

Turn the case upside down and attach the 4 self adhesive feet in the positions shown in Fig 6 below.

Fig 6

To remove the existing case from the recorder, remove the 4 M3 screws, 2 in each side.

43-TV-33-62 iss.1 GLO Oct 06 UK 4

43-TV-33-62 iss.1 GLO Oct 06 UK 5

Fig 7

Remove the 2

screws on each side

of the case

The case can then be removed from the recorder, complete with back panel by sliding backwards.

To fit the new portable case, carefully slide it on from the rear of the recorder. Ensure the case is orientated with the

handle on the top of the recorder.

Slide the case fully forward ensuring that no internal cables get trapped between the case and front bezel.

The case should sit flat on the back of the front bezel.

Re-fit the four M3 screws in the sides of the case.

Fig 8

Re-fit the 4

screws in the

portable case

Remove the rear panel from the old case by removing the two M3 screws that hold it in place.

To replace the rear panel on the new case, angle the rear panel as shown to line up two location points with the floor of

the recorder’s case.

Fig 9

Re-fit the M3 screw in the top right hand corner.

See Fig 10

Fig 10

43-TV-33-62 iss.1 GLO Oct 06 UK 6

Terminal Cover

When in use the terminal cover should be fitted to protect the user from any hazardous voltages that may be present on

the connectors plugged into the back of the recorder. Clearly the cover should not be fitted until all connections have

been made to the back of the recorder.

To fit the terminal cover align the cover with the back of the recorder and fit the top left hand screw which holds the

terminal cover, rear panel and case together. See Fig 11.

Fig 11

43-TV-33-62 iss.1 GLO Oct 06 UK 7

Turn the recorder on its side and fit the bottom terminal cover fixing screw Fig 12.

Fig 12

Fit M3

screw

Fit M3

screw

Copyrighted Materials. For more information please contact your supplier.

Inhaltsverzeichnis

Andere Honeywell Messgerät Handbücher

Honeywell

Honeywell Sensepoint XCL Bedienungsanleitung

Honeywell

Honeywell Q4000 Bedienungsanleitung

Honeywell

Honeywell HERMetic UTImeter Gtex Chem Bedienungsanleitung

Honeywell

Honeywell Limitless WPMM Series Bedienungsanleitung

Honeywell

Honeywell RAE Systems NeutronRAE II Bedienungsanleitung

Honeywell

Honeywell NOTIFIER AM-8200 Bedienungsanleitung

Honeywell

Honeywell RMA300-ME Bedienungsanleitung

Honeywell

Honeywell AUTOCUBE 8200 Bedienungsanleitung

Honeywell

Honeywell NK Bedienungsanleitung

Honeywell

Honeywell RM640 Bedienungsanleitung

Honeywell

Honeywell Enraf FlexLine RMA805 Bedienungsanleitung

Honeywell

Honeywell A700 Bedienungsanleitung

Honeywell

Honeywell C7355A1050 Bedienungsanleitung

Honeywell

Honeywell VERSAFLOW VORTEX 200 Verdrahtungsschema

Honeywell

Honeywell HERMetic PRESS Bedienungsanleitung

Honeywell

Honeywell BendixKing KLR 10 Bedienungsanleitung

Honeywell

Honeywell BK-G1.6A Bedienungsanleitung

Honeywell

Honeywell SmartLine RMA800 Bedienungsanleitung

Honeywell

Honeywell Themis alpha EI2 Bedienungs- und Wartungshandbuch

Honeywell

Honeywell Vertex M Bedienungsanleitung

Honeywell

Honeywell E3Point Bedienungsanleitung

Honeywell

Honeywell W8710A Bedienungsanleitung

Honeywell

Honeywell AC-250NXS Bedienungsanleitung

Honeywell

Honeywell TMS 9250 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung