Honeywell XENON 1900 Bedienungsanleitung

™

Xenon™ 1900/1902

Area-Imaging Scanner

User’s Guide

Disclaimer

Honeywell International Inc. (“HII”) reserves the right to make changes in speci-

fications and other information contained in this document without prior notice,

and the reader should in all cases consult HII to determine whether any such

changes have been made. The information in this publication does not repre-

sent a commitment on the part of HII.

HII shall not be liable for technical or editorial errors or omissions contained

herein; nor for incidental or consequential damages resulting from the furnish-

ing, performance, or use of this material.

This document contains proprietary information that is protected by copyright.

All rights are reserved. No part of this document may be photocopied, repro-

duced, or translated into another language without the prior written consent of

HII.

Other product names or marks mentioned in this document may be trademarks

or registered trademarks of other companies and are the property of their

respective owners.

Web Address: www.honeywellaidc.com

Microsoft® Windows®, Windows NT®, Windows 2000, Windows ME, Windows

XP, and the Windows logo are trademarks or registered trademarks of Microsoft

Corporation.

The Bluetooth® word mark and logos are owned by Bluetooth SIG, Inc.

Other product names or marks mentioned in this document may be trademarks

or registered trademarks of other companies and are the property of their

respective owners.

Product Agency Compliance - Xenon 1900

USA

FCC Part 15 Subpart B Class B

This device complies with part 15 of the FCC Rules. Operation is subject to

the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including

interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a

Class B digital device pursuant to part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses, and can radi-

ate radio frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio communica-

tions. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equip-

ment off and on, the user is encouraged to try to correct the interference by

one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

• Consult the dealer or an experienced radio or television technician for

help.

If necessary, the user should consult the dealer or an experienced radio/

television technician for additional suggestions. The user may find the fol-

lowing booklet helpful: “Something About Interference.” This is available at

FCC local regional offices. Honeywell is not responsible for any radio or

television interference caused by unauthorized modifications of this equip-

ment or the substitution or attachment of connecting cables and equipment

other than those specified by Honeywell. The correction is the responsibil-

ity of the user.

Use only shielded data cables with this system.

Caution: Any changes or modifications made to this equipment not

expressly approved by Honeywell may void the FCC authorization to oper-

ate this equipment.

UL Statement

UL listed: UL60950-1.

Canada

Industry Canada ICES-003

This Class B digital apparatus complies with Canadian ICES-003. Opera-

tion is subject to the following conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including

interference that may cause undesired operation.

Conformité à la règlementation canadienne

Cet appareil numérique de la Classe A est conforme à la norme NMB-003

du Canada. Son fonctionnement est assujetti aux conditions suivantes :

1. Cet appareil ne doit pas causer de brouillage préjudiciable.

2. Cet appareil doit pouvoir accepter tout brouillage reçu, y compris le

brouillage pouvant causer un fonctionnement indésirable.

cUL Statement

cUL listed: CSA C22.2 No.60950-1-03.

Europe

The CE marking indicates compliance to 2004/108/EC EMC Directive

with Standards EN55022 CLASS B, EN55024, EN61000-3-2,

EN61000-3-3. In addition, complies to 2006/95/EC Low Voltage Direc-

tive, when shipped with recommended power supply.

For further information please contact:

Honeywell Imaging & Mobility Europe BV

Nijverheidsweg 9-13

5627 BT Eindhoven

The Netherlands

Honeywell International Inc. shall not be liable for use of our product with

equipment (i.e., power supplies, personal computers, etc.) that is not CE

marked and does not comply with the Low Voltage Directive.

Waste Electrical and Electronic Equipment

Information

Honeywell complies with Directive 2002/96/EC OF THE EUROPEAN PAR-

LIAMENT AND OF THE COUNCIL of 27 January 2003 on waste electrical

and electronic equipment (WEEE).

This product has required the extraction and use of natural resources for its

production. It may contain hazardous substances that could impact health

and the environment, if not properly disposed.

In order to avoid the dissemination of those substances in our environment

and to diminish the pressure on the natural resources, we encourage you to

use the appropriate take-back systems for product disposal. Those sys-

tems will reuse or recycle most of the materials of the product you are dis-

posing in a sound way.

The crossed out wheeled bin symbol informs you that the product

should not be disposed of along with municipal waste and invites you to

use the appropriate separate take-back systems for product disposal.

If you need more information on the collection, reuse, and recycling sys-

tems, please contact your local or regional waste administration.

You may also contact your supplier for more information on the environ-

mental performances of this product.

Germany

If your product is marked with the GS symbol, then the product

has been issued a GS certificate showing compliance to IEC

60950-1.

Australia/NZ

C-Tick Statement

Conforms to AS/NZS 3548 EMC requirement

Mexico

Conforms to NOM-019.

Russia

International

Eye Safety Statement: LED

This device has been tested in accordance with IEC60825-1 LED safety,

and has been certified to be a Class 1 LED product.

CB Scheme

Certified to IEC60950-1 (2001) First Edition.

Patents

Please refer to the product packaging for patent information.

Solids and Water Protection

The Xenon 1900 has a rating of IP41, immunity of foreign particles and dripping

water.

Required Safety Labels

Scanner

Compliance

Label

location

Item

Number, Serial

Number and

Revision

Information

location

Illumination output

CCB01-010BT Base

Item Number,

Serial

Number and

Revision

Information

location

Compliance

Label

location

Chapter 1 - Getting Started

About This Manual ...................................................... 1-1

Unpacking Your Device............................................... 1-1

Connecting the Device ................................................ 1-2

Connecting with USB ............................................ 1-2

Connecting with Keyboard Wedge........................ 1-3

Connecting with RS232 Serial Port....................... 1-5

Connecting with RS485......................................... 1-6

Reading Techniques ................................................... 1-8

Menu Bar Code Security Settings ............................... 1-8

Resetting the Factory Defaults.................................... 1-9

Setting Custom Defaults ............................................. 1-9

Resetting the Custom Defaults ................................. 1-10

Chapter 2 - Programming the Interface

Introduction ................................................................. 2-1

Programming the Interface - Plug and Play ................ 2-1

Keyboard Wedge................................................... 2-1

Laptop Direct Connect........................................... 2-1

RS232 Serial Port.................................................. 2-2

RS485 ................................................................... 2-2

RS485 Packet Mode ............................................. 2-3

USB IBM SurePos................................................. 2-4

USB PC or Macintosh Keyboard........................... 2-4

USB HID................................................................ 2-5

USB Serial............................................................. 2-5

Verifone®Ruby Terminal Default Settings ............ 2-6

Gilbarco®Terminal Default Settings ..................... 2-7

Honeywell Bioptic Aux Port Configuration............. 2-7

Datalogic™ Magellan©Bioptic Aux Port

Configuration.................................................... 2-7

NCR Bioptic Aux Port Configuration...................... 2-8

Wincor Nixdorf Terminal Default Settings ............. 2-8

Table of Contents

Wincor Nixdorf Beetle™ Terminal

Default Settings................................................2-9

Keyboard Country Layout..........................................2-10

Keyboard Style ..........................................................2-17

Keyboard Conversion ................................................2-18

Control Character Output...........................................2-19

Keyboard Modifiers....................................................2-19

RS232 Baud Rate......................................................2-22

RS232 Word Length: Data Bits, Stop Bits,

and Parity ................................................................2-23

RS232 Receiver Time-Out.........................................2-24

RS232 Handshaking..................................................2-24

RS232 Timeout....................................................2-25

XON/XOFF ..........................................................2-25

ACK/NAK .............................................................2-25

Scanner to Bioptic Communication............................2-26

Scanner-Bioptic Packet Mode .............................2-26

Scanner-Bioptic ACK/NAK Mode.........................2-27

Scanner-Bioptic ACK/NAK Timeout.....................2-27

Chapter 3 - Cordless System Operation

How the Cordless Base Works....................................3-1

Linking the Scanner to the Base..................................3-1

Communication Between the Cordless System

and the Host..............................................................3-2

RF (Radio Frequency) Module Operation....................3-2

System Conditions.......................................................3-2

Linking Process .....................................................3-3

Scanner Is Out of Range .......................................3-3

Scanner Is Moved Back Into Range ......................3-3

Out of Range and Back into Range

with Batch Mode On.........................................3-3

Page Button.................................................................3-3

About the Battery.........................................................3-3

Charging Information .............................................3-4

Battery Recommendations ....................................3-4

Andere Handbücher für XENON 1900

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Honeywell Scanner Handbücher

Honeywell

Honeywell Vuquest 3330g Bedienungsanleitung

Honeywell

Honeywell MS4980 Bedienungsanleitung

Honeywell

Honeywell 4850DR Bedienungsanleitung

Honeywell

Honeywell Vuquest 3330g Bedienungsanleitung

Honeywell

Honeywell 7120 Orbit Bedienungsanleitung

Honeywell

Honeywell Voyager 1452g Series Bedienungsanleitung

Honeywell

Honeywell Voyager 1452g Series Bedienungsanleitung

Honeywell

Honeywell Vuquest 3310g Bedienungsanleitung

Honeywell

Honeywell 3900 Bedienungsanleitung

Honeywell

Honeywell Xenon 1932 Bedienungsanleitung

Honeywell

Honeywell XENON 1902G-BF Bedienungsanleitung

Honeywell

Honeywell Xenon 1932 Bedienungsanleitung

Honeywell

Honeywell IS4920 Bedienungsanleitung

Honeywell

Honeywell HF680 Bedienungsanleitung

Honeywell

Honeywell Voyager 1400g Series Bedienungsanleitung

Honeywell

Honeywell 8680i Series Bedienungsanleitung

Honeywell

Honeywell HH450 Bedienungsanleitung

Honeywell

Honeywell HF680 Bedienungsanleitung

Honeywell

Honeywell 8670 Bedienungsanleitung

Honeywell

Honeywell Vuquest 3330 Bedienungsanleitung

Honeywell

Honeywell Xenon Series Bedienungsanleitung

Honeywell

Honeywell StratosH MS2321 Bedienungsanleitung

Honeywell

Honeywell 4022 Benutzerhandbuch

Honeywell

Honeywell Xenon 1902HC Bedienungsanleitung

Beliebte Scanner Handbücher anderer Marken

Z/I Imaging

Z/I Imaging PhotoScan 2001 Bedienungsanleitung

Renkforce

Renkforce DS100-5M Bedienungsanleitung

Image Access

Image Access WideTEK A2 Bedienungsanleitung

Canon

Canon imageFORMULA CR-120N Bedienungsanleitung

Fujitsu

Fujitsu FI-4860C2 Bedienungsanleitung

GeoSlam

GeoSlam ZEB Horizon Montageanleitung

Kodak

Kodak i5800 Scanner Bedienungsanleitung

Kodak

Kodak i7300 Bedienungsanleitung

Revopoint

Revopoint POP Bedienungsanleitung

Fujitsu

Fujitsu fi-4860C Bedienungsanleitung

Eddyfi Technologies

Eddyfi Technologies Floormap X Bedienungsanleitung

Faselase

Faselase F6 Bedienungsanleitung

Fujitsu

Fujitsu CardMinder Bedienungsanleitung

Uniden

Uniden BC340CRS Bedienungsanleitung

Infinite Peripherals

Infinite Peripherals INFINEA TAB M Bedienungsanleitung

Mustek

Mustek PageExpress 4800 Pro Bedienungsanleitung

Optex

Optex 750830 Bedienungsanleitung

Innova

Innova 5210 Bedienungsanleitung