Honeywell SS4-AS Bedienungsanleitung

Installation Guide and Operating Manual

Multi-Spectrum Digital

Electro-Optical Fire Detector

Model SS4-AS/-AS2

For Special Applications

(Optimized for Hydrogen, Silane, Methanol, Ethanol, and Methane)

Stand-Alone Relay Mode or 4-20 mA Output Option

OPERATOR MANUAL // NOTICES AND TRADEMARKS

HONEYWELL 1

Notices and Trademarks

While this information is presented in good faith and believed to be accurate,

Honeywell disclaims the implied warranties of merchantability and fitness for a

particular purpose and makes no express warranties except as may be stated in

its written agreement with and for its customers.

In no event is Honeywell liable to anyone for any indirect, special or

consequential damages. The information and specifications in this document are

subject to change without notice.

The detector must be installed only by qualified professional personnel in

accordance with local codes.

The protection provided by the gas detector may be impaired if it is used in a

manner not specified by Honeywell Analytics.

ACCTTL, ALERT-1, ALARM-2, ALERT-1: ALARM 2, ALERT-1: ALARM-2,

ATAG, Clean Room Sentry, COP-i, Complete Optical Path Integrity, CM1, CM1-

A, DartLogic, FireLogic, Fire Signature Analysis, FireBusI, FireBusII, FirePic,

FirePicII, FirePicIII, FirePix, FirePicture, FSC, Fire Sentry Corporation, Fire

Sentry Corp., FSX, All FSX Nomenclature Variations (such as: FS2, FS2X, FS3,

FS3X, FS4, FS4X, FS5, FS5X, FS6, FS6X, FS7, FS7X, FS8, FS8X, FS9, FS9X,

FS10X, FS10X, FS11, FS11X, FS12, FS12X, FS14, FS14X, FS15, FS15X,

FS16, FS16X, FS17, FS17X FS18, FS18X, FS19, FS19X, FS20, FS20X, FS24,

FS24X, FS24XN, FS26, FS26X, FS26XN), FS7-2173-2RP, FS System 7, FS

System 10, FS7-2173, FS7-2173-RP, FS2000, FS System 2000, High Speed

Flame & Surveillance Detector, Multi-Spectrum QuadBand Triple IR, Multi-

Spectrum TriBand, Multi-Spectrum Tri-Band, Near Band Infrared, Near Band IR,

NearBand IR, QuadBand IR, Room Sentry, RS, RS2, SM2, SM3, SS, SS2,

SS2X, SS2-A, SS3, SS3-A, SS3X, SS4, SS4-A, SS4X, SnapShot, SLR-BIT,

SuperBus, SuperSentry, System 2000, Tri-Mode Plot, QuadBand Triple IR Plus,

TriBand, Tri-Band, “FS & FSC triangle logo’s”, WBIR, Wide Band Infrared,

WideBand IR, Wide Band IR

are registered trademarks of Honeywell International Inc.

Other brand or product names are trademarks of their respective owners.

Honeywell Analytics

OPERATOR MANUAL // SYMBOL DEFINITIONS

HONEYWELL 2

Symbol Definitions

The following table lists those symbols used in this document to denote certain

conditions.

Symbol Definition

ATTENTION: Identifies information that requires special

consideration.

TIP: Identifies advice or hints for the user, often in terms of

performing a task.

REFERENCE-EXTERNAL: Identifies an additional source of

information outside of this bookset.

REFERENCE-INTERNAL: Identifies an additional source of

information within this bookset.

Indicates a situation which, if not avoided, may result in

equipment or work (data) on the system being damaged or lost, or

may result in the inability to properly operate the process.

CAUTION: Indicates a potentially hazardous situation which, if not

avoided, may result in minor or moderate injury. It may also be used

to alert against unsafe practices.

CAUTION:Symbol on the equipment refers the user to the product

manual for additional information. The symbol appears next to

required information in the manual.

OPERATOR MANUAL // TABLE OFCONTENTS

HONEYWELL 3

TABLE OF CONTENTS

APPROVALS ............................................................................................... 5

SECTION 1 TECHNICAL DESCRIPTION ........................................................................ 6

1.1 Features and Specifications..................................................................................6

1.1.1 General Description.................................................................................6

1.1.2 Applications.............................................................................................8

1.1.3 Detector Locations...................................................................................8

1.2 Stand-Alone Operation .........................................................................................9

1.3 FS2000 System Operation....................................................................................9

1.4 Overview.............................................................................................................10

1.4.1 Model SS4-AS/-AS2 Detector...............................................................10

1.4.2 Detection Range and Field-of View.......................................................11

1.5 Configuration Settings.........................................................................................12

1.6 Testing................................................................................................................14

1.6.1 Special Conditions for Testing...............................................................14

1.6.2 Automatic Testing..................................................................................14

1.6.3 Manual Testing......................................................................................14

SECTION 2 INSTALLATION.......................................................................................... 15

2.1 Installation Instructions .......................................................................................15

2.1.1 Installation Precautions .........................................................................15

2.1.2 Conduit Installation................................................................................15

2.1.3 Wiring Recommendations .....................................................................15

2.1.4 Power Supply Considerations ...............................................................16

2.2 Installation Procedure.........................................................................................16

2.2.1 Configuring and Wiring Detectors..........................................................16

2.2.2 Removing Detector From Its Enclosure.................................................16

2.2.3 Configuring the Detector Module...........................................................16

2.2.4 Wiring the Detector Module...................................................................17

2.2.5 Wiring the SS4-AS/-AS2 Detector for 4 or 20 mA Current

Mode Operation (Optional)...................................................................18

2.2.6 Wiring the Detector Relays....................................................................19

2.2.7 Replacing the Detector Module in the Enclosure...................................19

2.3 Enclosure Installation (optional)..........................................................................19

2.3.1 Installing the Detector on the Swivel Mount (SM2) or SS

Extra Duty (SM4) Swivel Mount............................................................19

SECTION 3 TROUBLESHOOTING AND MAINTENANCE............................................. 22

3.1 Model SS4-AS/-AS2 Detector Faults..................................................................22

3.2 Cleaning Windowed Enclosures and Detectors..................................................23

3.3 Personnel Training..............................................................................................23

3.4 Detector Repair...................................................................................................24

SECTION 4 DETECTOR CONNECTIONS & SWITCH OPTIONS................................... 25

Verification Time.................................................................................................26

Latching26

IR-Only Enable....................................................................................................26

Test Cycle...........................................................................................................26

Fire Range..........................................................................................................26

SECTION 5 OPTIONAL ACCESSORIES....................................................................... 26

OPERATOR MANUAL // TABLE OFCONTENTS

HONEYWELL 4

5.1 Air Shield for Applications in Contaminated Environment

(Part No. DASA1-P)............................................................................................27

5.2 PC Software Kit (2029-INTERFACE-KIT)...........................................................27

5.3 4-20 mA Option (MA420-4).................................................................................27

5.4 Detector Mounts (SM2 or SM4)..........................................................................27

5.5 Test Lamp (FT2045 or FT-2145).........................................................................27

SECTION 6 DETECTOR LABEL DRAWINGS ............................................................. 28

INDEX ........................................................................................................ 29

Read and understand this manual before installing or

operating equipment.

OPERATOR MANUAL // APPROVALS

HONEYWELL 5

APPROVALS

The Model SS4-AS/-AS2 Multi-Spectrum Fire Detectors have been manufactured

in compliance with the requirements of the ISO-9002 standard and have been

approved by:

•California State Fire Marshal (CSFM)

•Factory Mutual (FM)

•Canadian Standards (CSA)

•CENELEC approval by FM Approvals Ltd.Certification Service in

compliance with the ATEX Directive.

OPERATOR MANUAL // SECTION 1

TECHNICAL DESCRIPTION

HONEYWELL 6

SECTION 1

TECHNICAL DESCRIPTION

1.1 Features and Specifications

1.1.1 General Description

The Model SS4-AS/-AS2 Multi-Spectrum Electro-Optical Fire/Flame Detectors are

fast-reacting (within 5 seconds), digital, configurable, microprocessor-based,

“smart” units. This Detector has sensitivity to Type A, B, and C flaming fires. They

are optimized for detection of hydrogen, ethanol, methanol, and methane (natural

gas) fires. Detectors of this design process Ultraviolet (UV), Wide Band Infrared

(IR), and Visible (VIS) spectral ranges from ruggedized Solar-blind UV, “Quantum-

Effect” IR, and Visible (VIS) sensors correspondingly. They are equipped with

SRL-BIT (Built In Test) for optical “through the lens” of both the sensors and lens.

These UV, IR, and VIS Fire Detectors have false alarm immunity, and alarm range

between 15 and 60 feet for a one square foot heptane, gasoline, kerosene, or

isopropyl alcohol pan flame with a 120-degree (±60 degrees from the axis)

conical field of view. Additional optimization for hydrogen assures a less than 5

second response to a 10-inch hydrogen flame at 15 ft.. Their microprocessor-

based algorithms (FirePic, SnapShot, and Tri-Mode Plot) assure time

programmable alarm verification, Fire Signature Analysis, and compatibility with

standard FM Approved or UL Listed fire alarm panels.

The Detector has the flexibility to be re-configured in the field. Its installation is

simple, and operation straightforward due to the built-in self-testing feature.

Therefore, the maintenance consists mainly in keeping the Detector window lens

clean, and performing periodic testing required by the manufacturer of the Fire

Control and Suppression System.

OPERATOR MANUAL // SECTION 1

TECHNICAL DESCRIPTION

HONEYWELL 7

Other Specifications:

Housing: Explosion-Proof, Copper-free Aluminum (< 0.4%) with powder

coated finish, or Optional 316 Stainless Steel, NEMA type 3 and

type 4, tamper-resistant with integral dual ¾ inch NPT conduit

openings.

Marking: Class I, Div. 1 & 2, Groups B, C, & D

Class II, Div. 1 & 2, Groups E, F, & G

Class III

Class I Zone 1 AEx d IIC

Ex d IIC; Ex tb IIIC

Temperature: Operation: -40 to +85°C (-40 to +185º F)

Storage:-55 to 105°C

Humidity range: 10% to 90% (RH), non-condensing

NOTE: The supply connection wiring shall be rated at least

10°C above the rated service temperature (95°C for T4 applications

and 85°C for T5 applications). See Figures 8 and 9 on Page 17 of this

Insruction Manual.

Weight: Aluminum housing is approximately 3.8 lbs.

Stainless Steel is approximately 8.9 lbs

Dimensions: 4.81 inches diameter by 4.40 inches high

LED Visual Indicators:

Powered Detector: Dual LEDs blink every 10 seconds

Fault Declared: One LED turns ON solid until the fault is cured

Re-calibrate when: Both LEDs flash ON and OFF rapidly

Fire Declared: Both LEDs ON solid (one LED blinks during first

few seconds)

OPERATOR MANUAL // SECTION 1

TECHNICAL DESCRIPTION

HONEYWELL 8

Electrical Power Requirements:

Connectors: WECO type screw connectors, recommended

Wire: 18 to 24 AWG

Input Voltage range: 24 Volts DC nominal, 20.5 to 32 Volts DC

Normal Operation Current: 68 mA nominal (72 with optional

MA420-4 Module)

Fire Alarm Current: 75 mA nominal (95 with optional MA420-4

Module)

Analog Current Output: 4 or 20 mA with optional MA420-4 Module.

Relay Contact:

Rating: 0.5 Amp at 120 Volt AC or 1 A at 24 V DC

resistive

Fire relay: N.O. and N.C. contacts (Latching/Non-Latching,

switch selected)

Verification relay: N.O. and N.C. contacts (Adjustable time from

0 to 30 seconds)

Fault relay: N.O. and N.C. contacts

1.1.2 Applications

Applications of the Model SS4-AS/-AS2 Detectors include storage warehouses of

Ethanol, Methanol, and Methane (Natural Gas) and Hydrogen gas, among others.

1.1.3 Detector Locations

For unobstructed performance, considering Detector locations in application

areas, avoid sources, other than fire, which may cause false alarms, such as

operations utilizing welding or gas torch equipment, high power sources of EMI

or RFI, or artificial lighting pointed directly at the Detector. Locations experiencing

strong mechanical or acoustical vibrations should also be avoided. For optimum

performance, locate the Detector(s) as close as possible to the potential fire

source, preferably, along the axis of the vision cone. Install enough Detectors to

completely eclipse the fire hazardous area. Assure accessibility for the Detector

lens cleaning, as well as best possible protection and/or cleaning from fog, rain,

ice, dust, hazardous atmospheres, and other adverse elements. If necessary,

utilize the Steel Swivel Mount (Model SM2) or 316 Stainless Steel Swivel Mount

(Model SM4) for greater flexibility in mounting locations (See Figures 4 and 5).

OPERATOR MANUAL // SECTION 1

TECHNICAL DESCRIPTION

HONEYWELL 9

1.2 Stand-Alone Operation

For Stand-Alone operation, the Detector may be connected to a FM Approved or

UL listed Fire/Security Panel. The Detector operated in the Stand-Alone mode,

uses the Fire, Fault, and Verify (optional) relays or optional 4 to 20 mA current

source (FSC Model MA420-4 Module, refer to Section 4.3) to interface with the

Fire/Security Panels. For Stand-Alone operation, the Detector’s Fault relay is

automatically configured by the on-board microprocessor. The input current of

the Detector is about 15 mA higher in the Stand-Alone mode compared to

FS2000 System operation.

NOTE: The Fault relay is not available when the Detector is wired to

the FS2000 System.

1.3 FS2000 System Operation

For FS2000 System operation, the Model SS4-AS/-AS2 Fire and Fault signals

are sent digitally to the FS2000 System Controller using the four wire FS2000

FireBus. The FireBus provides 24 Volt DC power for the Detector and RS-485

digital communication (Refer to Honeywell Analytics document MN0003:

"FS2000 FIRE EARLY WARNING SYSTEM - INSTALLATION and

OPERATIONS GUIDE"). For special remote alarm applications, users may also

connect directly to the Detector’s Fire alarm relay.

NOTE: When the Model SS4-AS/-AS2 Detector is connected to

the FS2000 System using FireBus communication, the Controller

automatically disables the Detector’s Fault relay.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Honeywell Rauchmelder Handbücher

Honeywell

Honeywell FireLite BEAM355 Bedienungsanleitung

Honeywell

Honeywell FAAST LT Bedienungsanleitung

Honeywell

Honeywell FMST FXV(E) Series Bedienungsanleitung

Honeywell

Honeywell Xtralis FAAST FLEX FLX-010 Bedienungsanleitung

Honeywell

Honeywell 5800COMBO-CN Bedienungsanleitung

Honeywell

Honeywell DFS8MS Bedienungsanleitung

Honeywell

Honeywell Notifier FSP-851 Bedienungsanleitung

Honeywell

Honeywell SS4-AI Bedienungsanleitung

Honeywell

Honeywell SS4-A HART Bedienungsanleitung

Honeywell

Honeywell Gamewell Velociti 3 Series Bedienungsanleitung

Honeywell

Honeywell Gamewell 7100 Series Montageanleitung

Honeywell

Honeywell NOTIFIER NFXI-ASD11 Kurzanleitung

Honeywell

Honeywell V-PLEX 5192SD Bedienungsanleitung

Honeywell

Honeywell FCI 2151 Bedienungsanleitung

Honeywell

Honeywell Velociti 3 Series Bedienungsanleitung

Honeywell

Honeywell C8600A Bedienungsanleitung

Honeywell

Honeywell GENT Venturi-Air Duct Kit Bedienungsanleitung

Honeywell

Honeywell Lyric Bedienungsanleitung

Honeywell

Honeywell DFS8MS Bedienungsanleitung

Honeywell

Honeywell DFS8MS Bedienungsanleitung

Honeywell

Honeywell DFS8MS Bedienungsanleitung

Honeywell

Honeywell compact asd Bedienungsanleitung

Honeywell

Honeywell TC842B1007AE Bedienungsanleitung

Honeywell

Honeywell SiX Series Bedienungsanleitung

Beliebte Rauchmelder Handbücher anderer Marken

x-sense

x-sense SD19-W Bedienungsanleitung

FireAngel

FireAngel Thermoptek ST-622 Bedienungsanleitung

teko

teko Astra-42A Bedienungsanleitung

Siemens

Siemens PE-11C Bedienungsanleitung

System Sensor

System Sensor DH500ACDC Bedienungsanleitung

Resolution Products

Resolution Products RE612 CryptiX Bedienungsanleitung

First Alert

First Alert PC900V Bedienungsanleitung

Eminent

Eminent EM6590 E-Domotica Bedienungsanleitung

Ei Electronics

Ei Electronics Ei Ei168RC Bedienungsanleitung

Carrier

Carrier Kidde Quell Q301 Bedienungsanleitung

VESDA

VESDA VLF-500 Bedienungsanleitung

ELRO

ELRO FS8110 Bedienungsanleitung

Heiman

Heiman SMOKI NS-626PHS Bedienungsanleitung

Family Gard

Family Gard FG225 Bedienungsanleitung

Regin

Regin SDD-S65 Bedienungsanleitung

Aparton

Aparton ASD-10 Bedienungsanleitung

Greystone

Greystone DSD120 Bedienungsanleitung

LST

LST ÜMS-55000-841 Bedienungsanleitung