Honeywell Y87RF Bedienungsanleitung

Andere Handbücher für Y87RF

4

Inhaltsverzeichnis

Andere Honeywell Thermostat Handbücher

Honeywell

Honeywell CT3611 Benutzerhandbuch

Honeywell

Honeywell VVT Bedienungsanleitung

Honeywell

Honeywell TH8320R1003 Bedienungsanleitung

Honeywell

Honeywell RTH221 Series Bedienungsanleitung

Honeywell

Honeywell T10 Pro Smart Bedienungsanleitung

Honeywell

Honeywell RTH111 series Bedienungsanleitung

Honeywell

Honeywell TH2110 Bedienungsanleitung

Honeywell

Honeywell T8600D Bedienungsanleitung

Honeywell

Honeywell WebStat T7350 Betriebsanleitung

Honeywell

Honeywell RTH7400 series Bedienungsanleitung

Honeywell

Honeywell T6570 Series Bedienungsanleitung

Honeywell

Honeywell T8601D Bedienungsanleitung

Honeywell

Honeywell T641A Bedienungsanleitung

Honeywell

Honeywell RTH2510 Series Bedienungsanleitung

Honeywell

Honeywell RTH3100C Bedienungsanleitung

Honeywell

Honeywell FocusPRO Wi-Fi TH6000 Series Bedienungsanleitung

Honeywell

Honeywell Lyric Bedienungsanleitung

Honeywell

Honeywell T498A Bedienungsanleitung

Honeywell

Honeywell T8621A Bedienungsanleitung

Honeywell

Honeywell CAMIR-8EZS Bedienungsanleitung

Honeywell

Honeywell INNCOM e7w Bedienungsanleitung

Honeywell

Honeywell RF CM61NG Bedienungsanleitung

Honeywell

Honeywell PRO 3000 Bedienungsanleitung

Honeywell

Honeywell TRUEZONE HZ322 Bedienungsanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung

Aube Technologies

Aube Technologies TH305 Bedienungsanleitung

Powtier Controls

Powtier Controls 505MST Bedienungsanleitung

Kanmor

Kanmor Zone Control 369e Bedienungsanleitung

MICROclimate International

MICROclimate International B2 Magic Eye Bedienungsanleitung

Installation Guide

Single Zone Thermostat

Y87RF

1. Disconnect the mains power from the Heating Appliance.

To ensure your safety, always make sure mains

power is switched off before accessing wiring.

3. Mount the wiring plate

to the wall or wallbox.

Note: the plugs and mounting

screws required are supplied.

4. Connect the Boiler Relay wiring.

Please refer

to wiring

diagram

(right).

2. Remove the wiring

plate from the

Boiler Relay.

2.1 Carefully press a

screwdriver into the

opening until the

cover comes free.

2.2 Tilt the cover upwards

and remove it.

5.1 Wiring for a basic boiler (not requiring a pump overrun).

The boiler relay powers the boiler live input.

230V

50-60Hz

<5A

N L

N L

L

BDR91

Place link here

A-B:5(3)A

A-C:5(3)A

A B C

L

N

230V

50-60Hz

<5A

N L L

BDR91 A-B:5(3)A

A-C:5(3)A

A B C

L

N

N L

5.2 Wiring for a boiler that requires a permanent live.

For use with a boiler that requires a permanent live

(a typical Combi boiler wiring). This can be used for

boilers with low voltage or 230Vac room thermostat

inputs. Please check manufacturer’s instructions.

5.3 Wiring for a two-port zone valve.

For use with a boiler that requires a permanent live.

Please check manufacturer’s instructions.

230V

50-60Hz

<5A

N L L

BDR91

V4043H

A-B:5(3)A

A-C:5(3)A

A B C

L

N

BL BR

M

GR O

G

/

Y

G/Y: Green/Yellow

Earth wire

BL: Blue Motor Neutral

BR: Brown Motor Live

GR: Grey End

switch (if used)

Permanent Live

O: Orange End

switch (If used).

In wired system

this typically

feeds the boiler.

continued overleaf

7. Reconnect the mains power to the Heating Appliance.

8. Locate the thermostat.

• Away from draughts

• Away from heat sources

• Away from direct sunlight

• Positioned about 1.2m –1.5m from the oor

6. Attach the Boiler Relay

to the wiring plate.

Locate hinges rst

Hinge the housing downwards

and click into place.

Manufactured for and on behalf of the

Environmental and Combustion Controls

Division of Honeywell Technologies Sàrl,

ACS-ECC EMEA, Z.A. La Pièce 16,

1180 Rolle, Switzerland by its Authorised

Representative Honeywell Inc.

Need help? For assistance please visit:

www.honeywelluk.com

Honeywell Control Systems Ltd.

Skimped Hill Lane, Bracknell, Berkshire

RG12 1EB

WEEE Directive

2012/19/EC

Waste Electrical

and Electronic

Equipment directive

•Attheendoftheproductlifedispose

of the packaging and product in a

corresponding recycling centre.

•Donotdisposeoftheunitwith

the usual domestic refuse.

•Donotburntheproduct.

•Removethebatteries.

•Disposeofthebatteriesaccordingto

the local statutory requirements and

not with the usual domestic refuse.

Approvals

Conforms to protection requirements

of the following directives:

EMC: 2004/108/EC

LVD: 2006/95/EC

R&TTE: 1999/05/EC

Hereby, Honeywell, declares that this

Single Zone Thermostat is in compliance

with the essential requirements and other

relevant provisions of Directive 1999/5/EC.

Installation instructions

Power

supply from

fused spur

To heating appliance

1,5-2,5mm2

max 6mm

>7mm 0

<7mm 0

32301889-001 A

Installation Guide

Single Zone Thermostat

Y87RF

1. Disconnect the mains power from the Heating Appliance.

To ensure your safety, always make sure mains

power is switched off before accessing wiring.

3. Mount the wiring plate

to the wall or wallbox.

Note: the plugs and mounting

screws required are supplied.

4. Connect the Boiler Relay wiring.

Please refer

to wiring

diagram

(right).

2. Remove the wiring

plate from the

Boiler Relay.

2.1 Carefully press a

screwdriver into the

opening until the

cover comes free.

2.2 Tilt the cover upwards

and remove it.

5.1 Wiring for a basic boiler (not requiring a pump overrun).

The boiler relay powers the boiler live input.

230V

50-60Hz

<5A

N L

N L

L

BDR91

Place link here

A-B:5(3)A

A-C:5(3)A

A B C

L

N

230V

50-60Hz

<5A

N L L

BDR91 A-B:5(3)A

A-C:5(3)A

A B C

L

N

N L

5.2 Wiring for a boiler that requires a permanent live.

For use with a boiler that requires a permanent live

(a typical Combi boiler wiring). This can be used for

boilers with low voltage or 230Vac room thermostat

inputs. Please check manufacturer’s instructions.

5.3 Wiring for a two-port zone valve.

For use with a boiler that requires a permanent live.

Please check manufacturer’s instructions.

230V

50-60Hz

<5A

N L L

BDR91

V4043H

A-B:5(3)A

A-C:5(3)A

A B C

L

N

BL BR

M

GR O

G

/

Y

G/Y: Green/Yellow

Earth wire

BL: Blue Motor Neutral

BR: Brown Motor Live

GR: Grey End

switch (if used)

Permanent Live

O: Orange End

switch (If used).

In wired system

this typically

feeds the boiler.

continued overleaf

7. Reconnect the mains power to the Heating Appliance.

8. Locate the thermostat.

• Away from draughts

• Away from heat sources

• Away from direct sunlight

• Positioned about 1.2m –1.5m from the oor

6. Attach the Boiler Relay

to the wiring plate.

Locate hinges rst

Hinge the housing downwards

and click into place.

Manufactured for and on behalf of the

Environmental and Combustion Controls

Division of Honeywell Technologies Sàrl,

ACS-ECC EMEA, Z.A. La Pièce 16,

1180 Rolle, Switzerland by its Authorised

Representative Honeywell Inc.

Need help? For assistance please visit:

www.honeywelluk.com

Honeywell Control Systems Ltd.

Skimped Hill Lane, Bracknell, Berkshire

RG12 1EB

WEEE Directive

2012/19/EC

Waste Electrical

and Electronic

Equipment directive

•Attheendoftheproductlifedispose

of the packaging and product in a

corresponding recycling centre.

•Donotdisposeoftheunitwith

the usual domestic refuse.

•Donotburntheproduct.

•Removethebatteries.

•Disposeofthebatteriesaccordingto

the local statutory requirements and

not with the usual domestic refuse.

Approvals

Conforms to protection requirements

of the following directives:

EMC: 2004/108/EC

LVD: 2006/95/EC

R&TTE: 1999/05/EC

Hereby, Honeywell, declares that this

Single Zone Thermostat is in compliance

with the essential requirements and other

relevant provisions of Directive 1999/5/EC.

Installation instructions

Power

supply from

fused spur

To heating appliance

1,5-2,5mm2

max 6mm

>7mm 0

<7mm 0

32301889-001 A

Installation Guide

Single Zone Thermostat

Y87RF

1. Disconnect the mains power from the Heating Appliance.

To ensure your safety, always make sure mains

power is switched off before accessing wiring.

3. Mount the wiring plate

to the wall or wallbox.

Note: the plugs and mounting

screws required are supplied.

4. Connect the Boiler Relay wiring.

Please refer

to wiring

diagram

(right).

2. Remove the wiring

plate from the

Boiler Relay.

2.1 Carefully press a

screwdriver into the

opening until the

cover comes free.

2.2 Tilt the cover upwards

and remove it.

5.1 Wiring for a basic boiler (not requiring a pump overrun).

The boiler relay powers the boiler live input.

230V

50-60Hz

<5A

N L

N L

L

BDR91

Place link here

A-B:5(3)A

A-C:5(3)A

A B C

L

N

230V

50-60Hz

<5A

N L L

BDR91 A-B:5(3)A

A-C:5(3)A

A B C

L

N

N L

5.2 Wiring for a boiler that requires a permanent live.

For use with a boiler that requires a permanent live

(a typical Combi boiler wiring). This can be used for

boilers with low voltage or 230Vac room thermostat

inputs. Please check manufacturer’s instructions.

5.3 Wiring for a two-port zone valve.

For use with a boiler that requires a permanent live.

Please check manufacturer’s instructions.

230V

50-60Hz

<5A

N L L

BDR91

V4043H

A-B:5(3)A

A-C:5(3)A

A B C

L

N

BL BR

M

GR O

G

/

Y

G/Y: Green/Yellow

Earth wire

BL: Blue Motor Neutral

BR: Brown Motor Live

GR: Grey End

switch (if used)

Permanent Live

O: Orange End

switch (If used).

In wired system

this typically

feeds the boiler.

continued overleaf

7. Reconnect the mains power to the Heating Appliance.

8. Locate the thermostat.

• Away from draughts

• Away from heat sources

• Away from direct sunlight

• Positioned about 1.2m –1.5m from the oor

6. Attach the Boiler Relay

to the wiring plate.

Locate hinges rst

Hinge the housing downwards

and click into place.

Manufactured for and on behalf of the

Environmental and Combustion Controls

Division of Honeywell Technologies Sàrl,

ACS-ECC EMEA, Z.A. La Pièce 16,

1180 Rolle, Switzerland by its Authorised

Representative Honeywell Inc.

Need help? For assistance please visit:

www.honeywelluk.com

Honeywell Control Systems Ltd.

Skimped Hill Lane, Bracknell, Berkshire

RG12 1EB

WEEE Directive

2012/19/EC

Waste Electrical

and Electronic

Equipment directive

•Attheendoftheproductlifedispose

of the packaging and product in a

corresponding recycling centre.

•Donotdisposeoftheunitwith

the usual domestic refuse.

•Donotburntheproduct.

•Removethebatteries.

•Disposeofthebatteriesaccordingto

the local statutory requirements and

not with the usual domestic refuse.

Approvals

Conforms to protection requirements

of the following directives:

EMC: 2004/108/EC

LVD: 2006/95/EC

R&TTE: 1999/05/EC

Hereby, Honeywell, declares that this

Single Zone Thermostat is in compliance

with the essential requirements and other

relevant provisions of Directive 1999/5/EC.

Installation instructions

Power

supply from

fused spur

To heating appliance

1,5-2,5mm2

max 6mm

>7mm 0

<7mm 0

32301889-001 A

Installation Guide

Single Zone Thermostat

Y87RF

1. Disconnect the mains power from the Heating Appliance.

To ensure your safety, always make sure mains

power is switched off before accessing wiring.

3. Mount the wiring plate

to the wall or wallbox.

Note: the plugs and mounting

screws required are supplied.

4. Connect the Boiler Relay wiring.

Please refer

to wiring

diagram

(right).

2. Remove the wiring

plate from the

Boiler Relay.

2.1 Carefully press a

screwdriver into the

opening until the

cover comes free.

2.2 Tilt the cover upwards

and remove it.

5.1 Wiring for a basic boiler (not requiring a pump overrun).

The boiler relay powers the boiler live input.

230V

50-60Hz

<5A

N L

N L

L

BDR91

Place link here

A-B:5(3)A

A-C:5(3)A

A B C

L

N

230V

50-60Hz

<5A

N L L

BDR91 A-B:5(3)A

A-C:5(3)A

A B C

L

N

N L

5.2 Wiring for a boiler that requires a permanent live.

For use with a boiler that requires a permanent live

(a typical Combi boiler wiring). This can be used for

boilers with low voltage or 230Vac room thermostat

inputs. Please check manufacturer’s instructions.

5.3 Wiring for a two-port zone valve.

For use with a boiler that requires a permanent live.

Please check manufacturer’s instructions.

230V

50-60Hz

<5A

N L L

BDR91

V4043H

A-B:5(3)A

A-C:5(3)A

A B C

L

N

BL BR

M

GR O

G

/

Y

G/Y: Green/Yellow

Earth wire

BL: Blue Motor Neutral

BR: Brown Motor Live

GR: Grey End

switch (if used)

Permanent Live

O: Orange End

switch (If used).

In wired system

this typically

feeds the boiler.

continued overleaf

7. Reconnect the mains power to the Heating Appliance.

8. Locate the thermostat.

• Away from draughts

• Away from heat sources

• Away from direct sunlight

• Positioned about 1.2m –1.5m from the oor

6. Attach the Boiler Relay

to the wiring plate.

Locate hinges rst

Hinge the housing downwards

and click into place.

Manufactured for and on behalf of the

Environmental and Combustion Controls

Division of Honeywell Technologies Sàrl,

ACS-ECC EMEA, Z.A. La Pièce 16,

1180 Rolle, Switzerland by its Authorised

Representative Honeywell Inc.

Need help? For assistance please visit:

www.honeywelluk.com

Honeywell Control Systems Ltd.

Skimped Hill Lane, Bracknell, Berkshire

RG12 1EB

WEEE Directive

2012/19/EC

Waste Electrical

and Electronic

Equipment directive

•Attheendoftheproductlifedispose

of the packaging and product in a

corresponding recycling centre.

•Donotdisposeoftheunitwith

the usual domestic refuse.

•Donotburntheproduct.

•Removethebatteries.

•Disposeofthebatteriesaccordingto

the local statutory requirements and

not with the usual domestic refuse.

Approvals

Conforms to protection requirements

of the following directives:

EMC: 2004/108/EC

LVD: 2006/95/EC

R&TTE: 1999/05/EC

Hereby, Honeywell, declares that this

Single Zone Thermostat is in compliance

with the essential requirements and other

relevant provisions of Directive 1999/5/EC.

Installation instructions

Power

supply from

fused spur

To heating appliance

1,5-2,5mm2

max 6mm

>7mm 0

<7mm 0

32301889-001 A

Installation Guide

Single Zone Thermostat

Y87RF

1. Disconnect the mains power from the Heating Appliance.

To ensure your safety, always make sure mains

power is switched off before accessing wiring.

3. Mount the wiring plate

to the wall or wallbox.

Note: the plugs and mounting

screws required are supplied.

4. Connect the Boiler Relay wiring.

Please refer

to wiring

diagram

(right).

2. Remove the wiring

plate from the

Boiler Relay.

2.1 Carefully press a

screwdriver into the

opening until the

cover comes free.

2.2 Tilt the cover upwards

and remove it.

5.1 Wiring for a basic boiler (not requiring a pump overrun).

The boiler relay powers the boiler live input.

230V

50-60Hz

<5A

N L

N L

L

BDR91

Place link here

A-B:5(3)A

A-C:5(3)A

A B C

L

N

230V

50-60Hz

<5A

N L L

BDR91 A-B:5(3)A

A-C:5(3)A

A B C

L

N

N L

5.2 Wiring for a boiler that requires a permanent live.

For use with a boiler that requires a permanent live

(a typical Combi boiler wiring). This can be used for

boilers with low voltage or 230Vac room thermostat

inputs. Please check manufacturer’s instructions.

5.3 Wiring for a two-port zone valve.

For use with a boiler that requires a permanent live.

Please check manufacturer’s instructions.

230V

50-60Hz

<5A

N L L

BDR91

V4043H

A-B:5(3)A

A-C:5(3)A

A B C

L

N

BL BR

M

GR O

G

/

Y

G/Y: Green/Yellow

Earth wire

BL: Blue Motor Neutral

BR: Brown Motor Live

GR: Grey End

switch (if used)

Permanent Live

O: Orange End

switch (If used).

In wired system

this typically

feeds the boiler.

continued overleaf

7. Reconnect the mains power to the Heating Appliance.

8. Locate the thermostat.

• Away from draughts

• Away from heat sources

• Away from direct sunlight

• Positioned about 1.2m –1.5m from the oor

6. Attach the Boiler Relay

to the wiring plate.

Locate hinges rst

Hinge the housing downwards

and click into place.

Manufactured for and on behalf of the

Environmental and Combustion Controls

Division of Honeywell Technologies Sàrl,

ACS-ECC EMEA, Z.A. La Pièce 16,

1180 Rolle, Switzerland by its Authorised

Representative Honeywell Inc.

Need help? For assistance please visit:

www.honeywelluk.com

Honeywell Control Systems Ltd.

Skimped Hill Lane, Bracknell, Berkshire

RG12 1EB

WEEE Directive

2012/19/EC

Waste Electrical

and Electronic

Equipment directive

•Attheendoftheproductlifedispose

of the packaging and product in a

corresponding recycling centre.

•Donotdisposeoftheunitwith

the usual domestic refuse.

•Donotburntheproduct.

•Removethebatteries.

•Disposeofthebatteriesaccordingto

the local statutory requirements and

not with the usual domestic refuse.

Approvals

Conforms to protection requirements

of the following directives:

EMC: 2004/108/EC

LVD: 2006/95/EC

R&TTE: 1999/05/EC

Hereby, Honeywell, declares that this

Single Zone Thermostat is in compliance

with the essential requirements and other

relevant provisions of Directive 1999/5/EC.

Installation instructions

Power

supply from

fused spur

To heating appliance

1,5-2,5mm2

max 6mm

>7mm 0

<7mm 0

32301889-001 A

Installation Guide

Single Zone Thermostat

Y87RF

1. Disconnect the mains power from the Heating Appliance.

To ensure your safety, always make sure mains

power is switched off before accessing wiring.

3. Mount the wiring plate

to the wall or wallbox.

Note: the plugs and mounting

screws required are supplied.

4. Connect the Boiler Relay wiring.

Please refer

to wiring

diagram

(right).

2. Remove the wiring

plate from the

Boiler Relay.

2.1 Carefully press a

screwdriver into the

opening until the

cover comes free.

2.2 Tilt the cover upwards

and remove it.

5.1 Wiring for a basic boiler (not requiring a pump overrun).

The boiler relay powers the boiler live input.

230V

50-60Hz

<5A

N L

N L

L

BDR91

Place link here

A-B:5(3)A

A-C:5(3)A

A B C

L

N

230V

50-60Hz

<5A

N L L

BDR91 A-B:5(3)A

A-C:5(3)A

A B C

L

N

N L

5.2 Wiring for a boiler that requires a permanent live.

For use with a boiler that requires a permanent live

(a typical Combi boiler wiring). This can be used for

boilers with low voltage or 230Vac room thermostat

inputs. Please check manufacturer’s instructions.

5.3 Wiring for a two-port zone valve.

For use with a boiler that requires a permanent live.

Please check manufacturer’s instructions.

230V

50-60Hz

<5A

N L L

BDR91

V4043H

A-B:5(3)A

A-C:5(3)A

A B C

L

N

BL BR

M

GR O

G

/

Y

G/Y: Green/Yellow

Earth wire

BL: Blue Motor Neutral

BR: Brown Motor Live

GR: Grey End

switch (if used)

Permanent Live

O: Orange End

switch (If used).

In wired system

this typically

feeds the boiler.

continued overleaf

7. Reconnect the mains power to the Heating Appliance.

8. Locate the thermostat.

• Away from draughts

• Away from heat sources

• Away from direct sunlight

• Positioned about 1.2m –1.5m from the oor

6. Attach the Boiler Relay

to the wiring plate.

Locate hinges rst

Hinge the housing downwards

and click into place.

Manufactured for and on behalf of the

Environmental and Combustion Controls

Division of Honeywell Technologies Sàrl,

ACS-ECC EMEA, Z.A. La Pièce 16,

1180 Rolle, Switzerland by its Authorised

Representative Honeywell Inc.

Need help? For assistance please visit:

www.honeywelluk.com

Honeywell Control Systems Ltd.

Skimped Hill Lane, Bracknell, Berkshire

RG12 1EB

WEEE Directive

2012/19/EC

Waste Electrical

and Electronic

Equipment directive

•Attheendoftheproductlifedispose

of the packaging and product in a

corresponding recycling centre.

•Donotdisposeoftheunitwith

the usual domestic refuse.

•Donotburntheproduct.

•Removethebatteries.

•Disposeofthebatteriesaccordingto

the local statutory requirements and

not with the usual domestic refuse.

Approvals

Conforms to protection requirements

of the following directives:

EMC: 2004/108/EC

LVD: 2006/95/EC

R&TTE: 1999/05/EC

Hereby, Honeywell, declares that this

Single Zone Thermostat is in compliance

with the essential requirements and other

relevant provisions of Directive 1999/5/EC.

Installation instructions

Power

supply from

fused spur

To heating appliance

1,5-2,5mm2

max 6mm

>7mm 0

<7mm 0

32301889-001 A

Installation Guide

Single Zone Thermostat

Y87RF

1. Disconnect the mains power from the Heating Appliance.

To ensure your safety, always make sure mains

power is switched off before accessing wiring.

3. Mount the wiring plate

to the wall or wallbox.

Note: the plugs and mounting

screws required are supplied.

4. Connect the Boiler Relay wiring.

Please refer

to wiring

diagram

(right).

2. Remove the wiring

plate from the

Boiler Relay.

2.1 Carefully press a

screwdriver into the

opening until the

cover comes free.

2.2 Tilt the cover upwards

and remove it.

5.1 Wiring for a basic boiler (not requiring a pump overrun).

The boiler relay powers the boiler live input.

230V

50-60Hz

<5A

N L

N L

L

BDR91

Place link here

A-B:5(3)A

A-C:5(3)A

A B C

L

N

230V

50-60Hz

<5A

N L L

BDR91 A-B:5(3)A

A-C:5(3)A

A B C

L

N

N L

5.2 Wiring for a boiler that requires a permanent live.

For use with a boiler that requires a permanent live

(a typical Combi boiler wiring). This can be used for

boilers with low voltage or 230Vac room thermostat

inputs. Please check manufacturer’s instructions.

5.3 Wiring for a two-port zone valve.

For use with a boiler that requires a permanent live.

Please check manufacturer’s instructions.

230V

50-60Hz

<5A

N L L

BDR91

V4043H

A-B:5(3)A

A-C:5(3)A

A B C

L

N

BL BR

M

GR O

G

/

Y

G/Y: Green/Yellow

Earth wire

BL: Blue Motor Neutral

BR: Brown Motor Live

GR: Grey End

switch (if used)

Permanent Live

O: Orange End

switch (If used).

In wired system

this typically

feeds the boiler.

continued overleaf

7. Reconnect the mains power to the Heating Appliance.

8. Locate the thermostat.

• Away from draughts

• Away from heat sources

• Away from direct sunlight

• Positioned about 1.2m –1.5m from the oor

6. Attach the Boiler Relay

to the wiring plate.

Locate hinges rst

Hinge the housing downwards

and click into place.

Manufactured for and on behalf of the

Environmental and Combustion Controls

Division of Honeywell Technologies Sàrl,

ACS-ECC EMEA, Z.A. La Pièce 16,

1180 Rolle, Switzerland by its Authorised

Representative Honeywell Inc.

Need help? For assistance please visit:

www.honeywelluk.com

Honeywell Control Systems Ltd.

Skimped Hill Lane, Bracknell, Berkshire

RG12 1EB

WEEE Directive

2012/19/EC

Waste Electrical

and Electronic

Equipment directive

•Attheendoftheproductlifedispose

of the packaging and product in a

corresponding recycling centre.

•Donotdisposeoftheunitwith

the usual domestic refuse.

•Donotburntheproduct.

•Removethebatteries.

•Disposeofthebatteriesaccordingto

the local statutory requirements and

not with the usual domestic refuse.

Approvals

Conforms to protection requirements

of the following directives:

EMC: 2004/108/EC

LVD: 2006/95/EC

R&TTE: 1999/05/EC

Hereby, Honeywell, declares that this

Single Zone Thermostat is in compliance

with the essential requirements and other

relevant provisions of Directive 1999/5/EC.

Installation instructions

Power

supply from

fused spur

To heating appliance

1,5-2,5mm2

max 6mm

>7mm 0

<7mm 0

32301889-001 A

10. Unclip the mounting plate.

Press the top of the

thermostat downwards, pull

it loose and tilt forwards.

9. First remove the dial.

12. Remove the protective tab

between the batteries.

11. Mount directly to the wall.

The plugs and mounting

screws required are supplied.

Plugs

Screws

14. Replace the dial.

13. Attach the thermostat to

the mounting plate.

Step 1

Hook in here

Step 2

Click into place

Binding to the Boiler Relay

The Single Zone Thermostat is supplied ready to install,

binding is only required if the Thermostat and Boiler Relay

are purchased separately.

2. You can now bind the Single

Zone Thermostat. Touch and

hold on the left touch zone for

approximately 10 seconds.

3. The screen for binding the

Boiler Relay is now displayed.

Successful binding Failed binding

1. First, set the Boiler Relay

into binding mode by holding

down the BIND button for

5 seconds, until the red

LED ashes 0.5 seconds

on 0.5 seconds off.

Press here 4. When the symbol ‘bo’ is flashing, briefly touch

the left touch zone to send the binding signal,

at which point the symbol will flash several times.

5. If binding has been successful the number indicates

the signal strength (1 = min to 5 = max).

If binding fails, appears on screen. Please try again.

6. The red LED on the Boiler Relay will turn off when binding

has been successful.

Note: binding can be cancelled from the binding

screen by touching and holding on the left touch

zone for approximately 10 seconds.

Installation Menu

The single Zone Thermostat has an Installation

Menu that is used to set the minimum and maximum

temperature limits and the off temperature setting.

Maximum and minimum temperatures:

The maximum temperature you can set your

thermostat to is 35ºC and the minimum is 5ºC.

The off temperature:

If the thermostat is operated remotely, this is the temperature

value that is used when it is switched off from the remote app.

4. Touch the left touch zone to

display the off temperature

setting. Change this using

the setting ring as before.

5. The Installation Menu closes

automatically 10 seconds

after the last action.

2. The maximum temperature

limit is now displayed. The

setting can be changed using

the setting ring. There is no

need to confirm the value.

Touch zones.

There are two touch zones just below the thermostat

display, which are used to access menus and functions.

3. While this setting is flashing,

touch the left touch zone

briefly to display the minimum

temperature limit. This can also

be changed using the setting ring.

1. Rotate the setting ring fully to

the left until the minimum value

is shown. When the value starts

flashing, touch and hold on both

left and right touch zonesfor

approximately 10 seconds.

Activate the Installation Menu as follows:

10s

10s 10s

10. Unclip the mounting plate.

Press the top of the

thermostat downwards, pull

it loose and tilt forwards.

9. First remove the dial.

12. Remove the protective tab

between the batteries.

11. Mount directly to the wall.

The plugs and mounting

screws required are supplied.

Plugs

Screws

14. Replace the dial.

13. Attach the thermostat to

the mounting plate.

Step 1

Hook in here

Step 2

Click into place

Binding to the Boiler Relay

The Single Zone Thermostat is supplied ready to install,

binding is only required if the Thermostat and Boiler Relay

are purchased separately.

2. You can now bind the Single

Zone Thermostat. Touch and

hold on the left touch zone for

approximately 10 seconds.

3. The screen for binding the

Boiler Relay is now displayed.

Successful binding Failed binding

1. First, set the Boiler Relay

into binding mode by holding

down the BIND button for

5 seconds, until the red

LED ashes 0.5 seconds

on 0.5 seconds off.

Press here 4. When the symbol ‘bo’ is flashing, briefly touch

the left touch zone to send the binding signal,

at which point the symbol will flash several times.

5. If binding has been successful the number indicates

the signal strength (1 = min to 5 = max).

If binding fails, appears on screen. Please try again.

6. The red LED on the Boiler Relay will turn off when binding

has been successful.

Note: binding can be cancelled from the binding

screen by touching and holding on the left touch

zone for approximately 10 seconds.

Installation Menu

The single Zone Thermostat has an Installation

Menu that is used to set the minimum and maximum

temperature limits and the off temperature setting.

Maximum and minimum temperatures:

The maximum temperature you can set your

thermostat to is 35ºC and the minimum is 5ºC.

The off temperature:

If the thermostat is operated remotely, this is the temperature

value that is used when it is switched off from the remote app.

4. Touch the left touch zone to

display the off temperature

setting. Change this using

the setting ring as before.

5. The Installation Menu closes

automatically 10 seconds

after the last action.

2. The maximum temperature

limit is now displayed. The

setting can be changed using

the setting ring. There is no

need to confirm the value.

Touch zones.

There are two touch zones just below the thermostat

display, which are used to access menus and functions.

3. While this setting is flashing,

touch the left touch zone

briefly to display the minimum

temperature limit. This can also

be changed using the setting ring.

1. Rotate the setting ring fully to

the left until the minimum value

is shown. When the value starts

flashing, touch and hold on both

left and right touch zonesfor

approximately 10 seconds.

Activate the Installation Menu as follows:

10s

10s 10s

10. Unclip the mounting plate.

Press the top of the

thermostat downwards, pull

it loose and tilt forwards.

9. First remove the dial.

12. Remove the protective tab

between the batteries.

11. Mount directly to the wall.

The plugs and mounting

screws required are supplied.

Plugs

Screws

14. Replace the dial.

13. Attach the thermostat to

the mounting plate.

Step 1

Hook in here

Step 2

Click into place

Binding to the Boiler Relay

The Single Zone Thermostat is supplied ready to install,

binding is only required if the Thermostat and Boiler Relay

are purchased separately.

2. You can now bind the Single

Zone Thermostat. Touch and

hold on the left touch zone for

approximately 10 seconds.

3. The screen for binding the

Boiler Relay is now displayed.

Successful binding Failed binding

1. First, set the Boiler Relay

into binding mode by holding

down the BIND button for

5 seconds, until the red

LED ashes 0.5 seconds

on 0.5 seconds off.

Press here 4. When the symbol ‘bo’ is flashing, briefly touch

the left touch zone to send the binding signal,

at which point the symbol will flash several times.

5. If binding has been successful the number indicates

the signal strength (1 = min to 5 = max).

If binding fails, appears on screen. Please try again.

6. The red LED on the Boiler Relay will turn off when binding

has been successful.

Note: binding can be cancelled from the binding

screen by touching and holding on the left touch

zone for approximately 10 seconds.

Installation Menu

The single Zone Thermostat has an Installation

Menu that is used to set the minimum and maximum

temperature limits and the off temperature setting.

Maximum and minimum temperatures:

The maximum temperature you can set your

thermostat to is 35ºC and the minimum is 5ºC.

The off temperature:

If the thermostat is operated remotely, this is the temperature

value that is used when it is switched off from the remote app.

4. Touch the left touch zone to

display the off temperature

setting. Change this using

the setting ring as before.

5. The Installation Menu closes

automatically 10 seconds

after the last action.

2. The maximum temperature

limit is now displayed. The

setting can be changed using

the setting ring. There is no

need to confirm the value.

Touch zones.

There are two touch zones just below the thermostat

display, which are used to access menus and functions.

3. While this setting is flashing,

touch the left touch zone

briefly to display the minimum

temperature limit. This can also

be changed using the setting ring.

1. Rotate the setting ring fully to

the left until the minimum value

is shown. When the value starts

flashing, touch and hold on both

left and right touch zonesfor

approximately 10 seconds.

Activate the Installation Menu as follows:

10s

10s 10s