Hoover C1412 Bedienungsanleitung

Commercial

Upright Vacuum

Cleaner

Operating Instructions

ENGLISH _ pp,1-13

ESPANOL _ p4g 14-20

FRAN(_AIS _ p. 21-27

Model Number

Serial Number

(Located on bottom of cleaner as shown)

Important Safeguards

When using an electrical appliance, always follow

basic precautions, including the following:

READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE

Review this manual

before operating

cleaner

Index

Assembling Cleaner .......................... 2-5

Cleaner Descriptions ............................ 6

How To Use

Cleaning Tools ................................ 8-9

To Clean Stairs .................................. 8

Upright Cleaner .............................. 6-8

If You Have a Problem ........................ 12

Important Safeguards .......................... 1

Lubrication .......................................... 12

Maintenance

Authorized Service .......................... 12

Replacing Agitator .......................... 11

Replacing Belt ............................ 10-11

Replacing Filter Bag .................... 9-10

Unpacking Cleaner .............................. 2

DOUBLE INSULATED: When servic-

ing, use only identical replacement

parts

vv a r n i n g : Toreducetheriskoffire, electric shock, or injury:

• Do not use outdoors or on wet surfaces.

• This appliance is provided with double insulation. Use only identical replacement

parts. See instructions for servicing double insulated appliances.

• Close supervision is necessary when any appliance is used by or near children.

Do not allow vacuum cleaner to be used as a toy or to run unattended at any time.

• Keep hair, loose clothing, fingers, feet and all parts of body away from openings,

rotating agitator and other moving parts. Do not operate cleaner in bare feet or

when wearing open toe shoes or sandals.

• Do not pick up anything that is burning or smoking, such as cigarettes, matches, or

hot ashes.

• Do not use to pick up flammable or combustible liquids such as gasoline or fine

wood sandings or use in areas where they may be present.

• Avoid picking up hard, sharp objects with the cleaner. They may damage the cleaner

and the bag.

• Do not use without dust bag or filters in place. Change bag frequently when picking

up very fine materials such as powder.

• Use extra care when cleaning on stairs.

• Do not put any object into openings. Do not use with any opening blocked; keep

free of dust, lint, hair, or anything that may reduce air flow.

• Do not pull or carry by cord, use cord as a handle, close door on cord or pull cord

around sharp edges or corners. Do not run appliance over cord. Keep cord away

from heated surfaces.

• Always disconnect cord from electrical outlet before servicing the cleaner.

• Unplug cleaner when not in use. Turn off all controls before unplugging.

• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord. Never

handle plug or appliance with wet hands.

• The use of an extension cord is not recommended.

• Do not use with damaged cord or plug. If appliance is not working as it should, has

been dropped, damaged, left outdoors, or dropped into water, take it to a Hoover

Factory Service Center or Authorized Hoover Warranty Service Dealer (Depot).

• Use vacuum cleaner only for its intended use as described in the instructions.

Use only attachments recommended by The Hoover Company; others may cause

hazards.

Save these instructions!

(_ 2001 The Hoover Company

Assembling cleaner

It is extremely important to read and

follow all instruction steps in order.

The assembled cleaner will look like this drawing,

-] S

A B @=_

Remove all parts from carton and identify each

item shown.

Make sure all parts, especially small items, such as G,

are located before disposing of cardboard packing.

A.Upper handle

B.Lower handle

C.Cord

D.Tool rack

E.Outer bag

F. Cleaner body

G.Handle bolt and nut packet

(One extra nut included)

H. Filter bag

I. Hose, cleaning tools and wand

Place upper (B) and lower (C) handle sections on a flat sur-

face with] cord hooks (A) on top, With] hands on sides of han-

dle sections, push] handle sections together firmly until they

"click" into place,

*Do not press against the rod (O) extending from the lower

handle. If the rod breaks or bends, the cleaner will not

work properly. Do not push handle together with your

hands on the ends of the sections.

Note: The small red tab (E) above the ON/OFF switch (F) is for shipping

purposes 0nly and may fall off during assembly. If it does not fail off, the tab

will be removed during the final steps of assembly.

Turn handle over. Insert large rectangular end of cord into pocket in bottom of

handle, with side marked "UP" visible.

Make sure rectangular end is pushed into handle as far as possible.

Slide cord protector (O) toward upper handle (B).

Rotate cord protector (G) on cord

until you see its arrow (H).

With arrow on cord protector (H)

pointing toward arrow on upper han-

dle (I), press groove (g)in

cord protector into slot (K) in upper

handle.

Pull cord tight.

Press cord into place at each of the three notches indic_ted and note correct

positioning of (G).

Do not plug cleaner in until assembly is totally complete.

Note location of tapered rails (L) on

back of outer bag base (M) and on

front of lower handle (C),

Slide rails on outer bag (M) onto

rails on lower handle (C) until outer

bag base snaps past the lock tab

(N).

Make sure hole in outer bag base

aligns with hole in handle (0).

Be sure that power cord is pulled

tight and pressed into each of the

three notches (Fig. 6) before com-

pleting the following steps.

Continued _ 3

Jl Jl

Note round opening (P) and hooks

(©) on b_ck of outer bag (M).

Place opening over dirt tube (R).

Unzip outer bag (M) and place hand

inside, Press down firmly to snap

hooks into handle.

_l_]lo]s_ _A1iw_[_illts_uitso m[:.In

With outer bag to the front, place

assembled handle onto handle base

of cleaner body.

Rock handle side to side while

pushing down firmly. Extra push-

ing effort may be required.

Press the handle release lever to

move handle to the operating or

middle position.

Push bolt (S) into I'lole on lower

front of handle.

If bolt will not go through hole

easily, handle is not pushed com-

pletely down.

Place nut in recessed area (T) at

back of handle. Hold nut in place

while tightening bolt securely with a

screw driver.

Note: Only one nut is needed on this

model. The extra nut is not required

but has been provided for your con-

venience.

Note: Do not hook b_g clip to retain-

er. This will be done in a later step.

#IIfI

//_'_.;/ //I tl I l.,d ._-'-,I II I P u

/ II/Z,L----'_ f/,Y_ II A\\\\_I k

Hold filter bag collar (U) as shown.

Align opening in filter bag with dirt

tube (V) inside the outer bag.

Push bag collar firmly onto tube (V).

Tuck in filter bag; zip outer bag.

Break off red tab (E) above ON/OFF

switch (F) by pushing down on tab.

Discard tab.

Note: If tab has come off during

assembly, make sure switch is in

the OFF position (down) before

plugging cord into an electrical

outlet.

_k e[=.]ojKo_-" _lJil_sN It1 e[ozo] mI_[e] _

|1 IIIFA

A,m \

Note: Bag clip on front of handle must

be unhooked from slot in bag cap

before attaching tool rack (see Fig.

26).

With side of rack marked TOP FRONT

(W) facing top of bag, pull cord

through rack and lower rack over han-

dle as shown. Slide rack down

between bag and handle,

Continue to slide rack down handle

until bottom of rack is below lower

cord hook (A). Snap one side of rack,

then the other onto lower handle.

4Continued -I_

Sliderackdownhandleuntilupper

hooks(X)snapintoslots (Y) on han-

dle, Place round end of hose over round

extension on bottom of rack. Press hose firmly into rack at upper

extensions.

Insert hose connector, with latch

toward front of cleaner, into opposite

side of rack.

With smaller end toward bottom,

snap wand (Z) into clips on rack.

Position dusting brush (AA) into rack

as shown.

Place furniture nozzle (Be) on lip on

lower part of rack and snap into

place.

Slide crevice tool (CC) onto projec-

tion (DD). Snap into place.

On upper front handle, grasp bag

clip (BE) and pull down firmly. Hook

bag clip into slot in bag cap.

CAUTION: When cleaner is turned

on, the agitator continues to

rotate while the handle is in the

upright position. Avoid tipping

cleaner or setting it on furniture,

fringed area rugs, or carpeted

stairs during tool use.

Continued _1_ 5

How to use

Cleaner description

WiN 1

The assembled cleaner will look like

the drawing.

1. Handle

2. Cord hooks: wrap cord around

hooks for storage. The top hook

can be rotated right or left for

easy cord release.

3. Bag Cap

4. ON/OFF switch: lock,ted on side

of handle

5. Outer bag

6. Stair cleaning handle: located on

lower edge of bag,

Z. Handle release lever: step on

lever to lower handle to operating

or low position.

8. Cleaner body

9. Nozzle control knob: slide knob

to correct setting for height of car-

pet being cleaned.

10. Furniture guard: helps prevent

cleaner from marking furniture.

11.Hood

12.Hose door: open door to connect

hose to cleaner.

13.Hose

14.Tool rack

15.Dusting brush

16.Wand

17.Furniture nozzle

18.Crevice tool

Operate cleaner only at voltage

specified on data plate on bottom

of cleaner.

Note: To reduce the risk of electric

shock, this appliance has a polar-

ized plug (one blade is wider than

the other). This plug will fit in a

polarized outlet only one way. If the

plug does not fit fully in the outlet,

reverse the plug. If it still does not

fit, contact a qualified electrician to

install the proper outlet. Do not

change the plug in any way.

P,_=!

To turn cleaner on, push switch up,

To turn cleaner off, push switch down.

Plug cord into electrical outlet. Turn

cleaner on and, with handle in

upright position, pull back on handle

until front of cleaner is lifted off the

carpet. This insures that the paper

bag is inflated.

Handle positions

The handle of your cleaner has

three positions; upright for storage

and when using cleaning tools;

operating position for general

operation on carpet and floors; _OW

for reaching under low furniture.

Step on handle release lever to

lower handle.

lmi m

Transporting cleaner

To move your cleaner from room to

room, put handle in upright position,

tilt cleaner back on rear wheels, and

push forward.

The cleaner can also be moved by

lifting it as shown. Oarpet height adjust-

ment

The cleaning of carpet and rugs takes

place at the nozzle (A),

[€]!l

If it is necessary to raise and lower the

nozzle for various carpet pile heights,

slide the nozzle control knob to the

desired setting.

For ease in sliding knob, the handle

should be in the upright position (B).

The nozzle will not move into the

adjusted position until the cleaner

handle is lowered to the operating

position (C).

(A) (B) H,GH

_l_ (1) (2) (3) (4)

eA_ FLOOR ..... =,,,,,_ll=lllllllllIlll

For maximum cleaning perfor-

mance, the following carpet height

settings are recommended,

Cleaners with Two Settings:

• Setting 1 (A): for bare floors and all

carpet types.

• Setting 2 (B): if easier pushing effort

is desired while maintaining good

cleaning performance.

Cleaners with Four Settings:

•Lowest setting (1): for bare floors

and low pile, level loop, kitchen type

carpet.

• Next setting (2): for other types of

carpet,

• Higher settings (3-4): for very deep

pile carpet where easier pushing effort

is desired, while maintaining good

cleaning performance.

Note: Ifthe cleaner is difficult to push,

slide knob to the next higher setting.

Cleaning lightweight

flexible rugs

Standononeendofrugandmove

cleanertowardotherendoredge.

Beforereachingedge,pushdown

onhandle.This will lift up the nozzle

(front of cleaner) and will prevent

rug from clinging to cleaner. Contin-

ue to lift up nozzle so that when you

have reached the edge, it is com-

pletely off the rug. Move cleaner

back to start again, lower nozzle,

and use only forward strokes.

Edge cleaning

Edge cleaning is provided on both

sides of nozzle to remove dirt in car-

pet near baseboards and furniture.

Guide either side of nozzle parallel

to edge of carpet or furniture.

Stair cleaning

A stair cleaning handle has been

designed for ease in using your

cleaner on stairs, With handle in

operating position, place fingers

under edge of stair cleaning handle

and guide cleaner with other hand

on upper handle.

As an alternative, you may use the

hose and furniture nozzle for stair

cleaning, cleaning from bottom to

top.

When using cleaning tools, the

agitator will continue to rotate.

CAUTION: To avoid personal

injury or unnecessary wear to car-

pet, and to prevent the cleaner

from falling, use extra care if

cleaner is placed on stairs.

Cleaning tools

Tool set includes a hose, wand,

crevice tool, furniture nozzle and

dusting brush,

Attach hose to cleaner

Turn cleaner off before attaching

or removing hose.

With cleaner handle in upright posi-

tion, open hose door and insert

hose connector until locked in posi-

tion, Suction will automatically be

diverted to the hose when cleaner is

turned on.

To remove hose, press latch (S) on

hose connector and pull up,

Note: Hose must be removed from

hose door when cleaning carpet

and rugs to insure proper clean-

ing performance.

CAUTION: Agitator continues to

rotate while cleaner handle is in

upright position. Avoid tipping

cleaner or setting it on furniture,

fringed area rugs or carpeted

stairs.

°&,

| f

Select proper tool

A. Dusting brush may be used for

carved furniture, table tops, books,

lamps, lighting fixtures, venetian

blinds, baseboards, shutters, and

registers.

B. Furniture nozzle may be used

for upholstered furniture, draperies,

mattresses, clothing, automobile

interiors, and carpeted stairs.

C. Crevice t001 may be used in tight

spaces, corners and along edges in

such places as dresser drawers,

upholstered furniture, stairs, and

baseboards.

D, Wand is used to give extra length

to your hose. Use it with any of the

above tools,

Attach wand and tools

The tools are attached to the hose or

the wand in the same manner. Push

tool firmly onto hose; twist tool slight-

ly to tighten or loosen connection,

Use cleaning tools with cleaner han-

dle in upright position.

Clearing blockages

To check for obstructions, first turn

cleaner off and disconnect from

electrical outlet; then disconnect

hose from cleaner. Open hose

door (E) and carefully remove any

visible obstruction, if no obstruction

is found, check hose and tools.

Remove obstruction, To continue

using tools, re-attach hose to clean-

er. If no obstruction is found and a

problem persists, contact your

Hoover Factory Service Center or

Authorized Warranty Service Dealer

Uepot).

ow to clean tools

To clean the hose, wipe off dirt with

a cloth dampened in a liquid deter-

gent. Rinse with a damp cloth.

Cleaning tools may be washed in

warm water with a detergent. Rinse

and air dry before using.

mw H wiwJm

Disconnect cleaner from electrical

outlet before attempting to service

it in any manner.

Do not operate without paper bag

in place.

The filter bag

When to replace

Check filter bag from time to time. It

is recommended that you change

the filter bag when dirt reaches the

dotted line. If more dirt than this

accumulates, your cleaner may not

operate effectively.

Note: Check and change the filter

bag frequently when using cleaner

on new carpet due to rapid accumu-

lation of carpet fluff.

CAUTION: Very fine materials,

such as face powder, cornstarch,

fireplace ashes or fireplace soot,

may seal the filter bag and may

cause it to burst even though it is

only partially full of dirt. When

cleaner is used to remove material

of this nature, change filter bag

often.

Where to buy

Filter bags may be purchased from

your local Authorized Hoover Dealer

(Depot), leading retailers, or from a

Hoover Factory Service Center.

What to buy

Use only Genuine HOOVER °'Aller-

gen Filtration T._T__._._disposable fil-

ter bags in order to maintain the

original cleaning effectiveness of

your cleaner.

Regular HOOVER _ Type Adispos-

able filter bags also fit your cleaner.

To assure that your cleaner operates

at peak performance, it is imperative

that you use only genuine HOOVER

filter bags made by The Hoover

Company. HOOVER bags can be

identified by these trademarks -

How to replace

Disconnect cleaner from electrical

outlet.

To change filter bag, unzip outer bag,

grasp sides of filter bag collar (A) and

pull collar from tube.

Note: Do not clean out old filter bag

and reuse. Discard used filter bag.

Continued _ 9

Hold new filter bag as shown. Align

opening in filter bag with dirt tube (B).

Push bag collar (A) firmly onto tube

(B).

Tuck in filter bag; zip outer bag.

The belt

The belt on your HOOVER cleaner

causes the agitator to rotate and is

important for the effective operation

of the cleaner. The belt is located

under the bottom plate of the clean-

er and should be checked from time

to time to be sure it is in good condi-

tion.

When to replace

To check belt, remove bottom plate

and hood as shown in "How to

replace belt." Replace belt if it is

stretched, cut or broken.

What to buy

To assure effective operation, use

only genuine HOOVER belts with

your cleaner. When purchasing a

new belt, ask for Hoover part No,

38528040.

How to replace

Disconnect cleaner from electrical

outlet.

Place handle in operating position

and turn cleaner over so bottom

side is up.

To remove bottom plate remove

screws (A), insert end of flat screw-

driver into wide area of right-hand

slot (B) and push handle of screw-

driver to the rear. Repeat in leR-hand

slot (B),

Lift extension (C) of bottom plate,

rotate plate and remove from clean-

er body.

Remove agitator and broken agitator

belt.

(If belt is not broken but is stretched

or cut, proceed with steps for Figs.

50 to 53 and pull belt off motor pul-

ley. Then continue with Fig. 48).

Slip agitator through new belt (with

lettering toward outside of clean-

er) and position belt in belt guide

(U). Push end of belt into opening in

cleaner body.

Reposition agitator making sure to

align flat sides of projection (E) on

belt end of agitator with flat sides of

slot (F) in cleaner body.

Place the three tabs on bottom plate

into slots in front of cleaner body.

Snap bottom plate into place over

agitator.

Andere Handbücher für C1412

Dieses Handbuch passt für folgende Modelle

Andere Hoover Staubsauger Handbücher

Hoover

Hoover Gator 10.8V Bedienungsanleitung

Hoover

Hoover Shampoo- Polisher Bedienungsanleitung

Hoover

Hoover UH70800 Bedienungsanleitung

Hoover

Hoover SteamVac supreme Bedienungsanleitung

Hoover

Hoover Enhanced Clean Bedienungsanleitung

Hoover

Hoover Hose Magic Bedienungsanleitung

Hoover

Hoover HF522SFP 011 Bedienungsanleitung

Hoover

Hoover U5140 Bedienungsanleitung

Hoover

Hoover UH60010 - WindTunnel Bagless Self Propelled Upright... Bedienungsanleitung

Hoover

Hoover Plus Bedienungsanleitung

Hoover

Hoover SteamVac Agility F6211 Bedienungsanleitung

Hoover

Hoover F8100900 - Platinum Carpet Cleaner Bedienungsanleitung

Hoover

Hoover SteamVac LS Bedienungsanleitung

Hoover

Hoover RC52SE 011 Bedienungsanleitung

Hoover

Hoover CL-EVERYDAY Series Bedienungsanleitung

Hoover

Hoover EVO Bedienungsanleitung

Hoover

Hoover SteamVac Commercial Spotter/Carpet Cleaner Bedienungsanleitung

Hoover

Hoover FloorMATE Floor Mate with Spin Scrub Brushes The Hard Floor... Bedienungsanleitung

Hoover

Hoover 5014 pets Bedienungsanleitung

Hoover

Hoover C1834 - HEPA 2 Motor Upright Datenblatt

Hoover

Hoover C1433-010 - COMPANY Commercial Guardsman Bagless Upright... Bedienungsanleitung

Hoover

Hoover Globe Bedienungsanleitung

Hoover

Hoover HC1600 Installationsanleitung

Hoover

Hoover Widepath LS Bedienungsanleitung

Beliebte Staubsauger Handbücher anderer Marken

Bissell

Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung

Panasonic

Panasonic MC-YL637S147-AE Bedienungsanleitung

NEFF

NEFF N17XH10 0 Series Bedienungsanleitung

LG A9 Series Bedienungsanleitung

Oreck

Oreck Cordless Captura BK51700 Series Bedienungsanleitung

Kogan

Kogan KAVACROBVWA Bedienungsanleitung

Kränzle

Kränzle VENTOS 50 ID Benutzerhandbuch

EVVO

EVVO Ai35 Bedienungsanleitung

DeWalt

DeWalt DWH200D Bedienungsanleitung

Pontec

Pontec Pondomatic Vacuum Cleaner Bedienungsanleitung

Cleanmaxx

Cleanmaxx PC-P007E Bedienungsanleitung

Exido

Exido 240-114 Bedienungsanleitung

RIDGID

RIDGID WD1685AU0 Bedienungsanleitung

Ezviz

Ezviz RE4P Bedienungsanleitung

STG global

STG global TANVAC HDV3000 Bedienungsanleitung

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Bedienungsanleitung

Factory

Factory M3340 Bedienungsanleitung

Shop-Vac

Shop-Vac VN92 SERIES Bedienungsanleitung