Hoover FH55000 Betriebsanleitung

Service Instructions

Hoover PowerDash Pet- PowerDash Pet Complete

PowerDash Pet Model #: FH50710V, FH50700UPC, FH50700, FH50710CN, FH50750, FH50700PDI

GL, FH50700FDI, FH50700CDI, FH50702, FH50703CDI, FH50700V, FH50750V, FH50750PDI,

FH50703VCD, FH50704, FH50704V, FH50711CN, FH50711V, FH50751, FH50751V, FH50751PDI,

FH50751VPD, FH50704FDI, FH50704VFD, FH50701CDI, FH50740CDI.

PowerDash Pet Complete Model #: FH50704, FH50711CN, FH50751, FH50751PDI, FH50704FDI,

FH50701CDI, FH50740CDI, FH50704V, FH50711V, FH50751V, FH50751VPD, FH50704VFD,

FH50701VCD, FH50740VCD, FH55050PC, FH55010, FH55000, FH55050V, FH55010V, FH55000V

TO VIEW PARTS SCHEMATICS PLEASE VISIT “PARTS CATALOG” THROUGH THE DEALER

PORTAL HOME PAGE.

Troubleshooting

A. Unit Leaking

1. The clean and dirty tank are not placed properly or might be filled.

(1) Check to ensure all tanks are properly filled or empty (dirty water tank cannot be over the

max limit, to prevent leaking through the motor)

(2) Ensure the tanks are firmly placed into the unit and there are no gaps or looseness.

2. Dirty Water Tank Lid is not secure.

(1) Make sure there are no gaps in your dirty water tank. Also check that the lid of your tank

is properly fitted in.

3. Check tanks to determine if leaking occurs while installed or removed from unit.

Clean Tank does have an amount of residual water when removed from tank resoivour.

Check tank caps to ensure seals are in place and sealing tanks.

4. Remind the customer to allow residual water to make its way back into the dirty water tank

after they are done cleaning. This is to prevent leaking once its stored.

B. Unit Won’t Dispense

1. Clean Water Tank is Empty and the handle is loose

(1) Check to ensure that the Clean Water Tank and solution tank is properly filled and

properly fitted into the unit

(2) The unit will not dispense if the handle is not properly installed

2. Unit may need to be flushed.

(1) Add warm tap water to both the clean water tank and the solution tank. Make sure both

tanks are seated firmly, turn the unit on, and recline the handle. Push the unit forward

continuously about 3-4 times or until water comes out of the bottom. Power ON again.

3. Unit may need to be reset.

To reset the PowerDash, unplug it from the wall. Remove the nozzle cover and take out the

brushes. Now, replace the nozzle cover, plug the unit back in, and cycle the power on and off

4 times. Replace the brushes and test to see if the reset worked.

C. Accessory Hose/Tool Won’t Dispense (ONLY for PowerDash Pet Complete)

1. Check to ensure that Clean Water Tank and Solution Tanks are full.

2. Ensure there are no clogs in the hose end.

(1) Check both ends of the hose and clean any clogs or debirs you may encunter. Make sure

they also clean the accesory tools.

(2) Insert a small object into the hose solution port to ensure is not clogged.

3. There may be air trapped in the hose and pump. In this case, you will need to prime the pump

by lowering the hose to the floor and holding the trigger for up to one minute.

D. Unit Won’t Pick Up or Has Poor Suction

1. Dirty Water Tank is Full (Float Engaged), the float can also be tripped if the unit is lifted

from the floor while is ON.

(1) Turn off the unit and empty the Dirty Water Tank. They will notice the float goes back to

its original position.

2. The Nozzle is not secure

(1) Pull up on the latch and pull forward to remove the nozzle cover. Check the nozzle

opening for any clogs or blockages. To replace the nozzle cover, line up the two tabs on

the base as well as the tabs close to the opening. Push down and backward until the latch

clicks into place.

(2) On the PowerDash Pet Complete there a quick access to the brush roll for cleanup. See

picture 2 below.

3. The debris filter is dirty

(1) Remove the debris filter, located under the Dirty Water Tank, wipe it clean.

4. There is a clog in the tool at the end of the hose.

(1) Remove the tool and clear out any debris.

5. The Unit needs to be reset

(1) To reset the PowerDash, unplug it from the wall. Remove the nozzle cover and take out

the brushes. Now, replace the nozzle cover, plug the unit back in, and cycle the power on

and off 4 times. Replace the brushes and test to see if the reset worked.

E. Brushroll Not Spinning

1. Make sure the unit is NOT in the upright position

(1) If the unit is in the upright position, the brushroll won’t spin. Tilt the unit backwards.

2. The brushroll stall protection has been activated. This happens when the brushroll gets

jammed or clogged.

(1) Turn the unit off and back ON again.

(2) Make sure to remove your brushroll and clean any tangled hair or debris that could be

causing the stall. Temember to clean the notches inside the nozzle too.

See below

3. The belt might be broken. (You may experience a burning smell, or a high pitch sound)

(1) Remove the bottom plate of the unit and remove the brushroll.

(2) Place the new belt on the motor shaft

(3) Position the non-belt side of the roll into the notch it belong to.

(4) Carefully stretch the belt to position the other en cap into the notch

(5) Replace the belt cover and secure the 6 screws to the plate.

See below

F. Unit Not Turning ON

(1) Make sure their unit is firmly plugged into a working outlet.

(2) Check there are no outages or issues with the fuse at the customer’s home

(3) The thermal protector might have activated. The unit does this to prevent damage from

overheating.

(a) Unplug the unit from the outlet.

(b) Clean the dirty and clean water tanks

(d) Allow the unit to cool down for up to 30 minutes. Then plug back ON

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Hoover Staubsauger Handbücher

Hoover

Hoover SmartWash+ FH52000 Bedienungsanleitung

Hoover

Hoover WINDTUNNEL Tangle Guard Bedienungsanleitung

Hoover

Hoover SteamVac TurboPOWER F5893-900 Bedienungsanleitung

Hoover

Hoover Chorus CH50PET 011 Bedienungsanleitung

Hoover

Hoover Jive Bedienungsanleitung

Hoover

Hoover FREESPACE EVO Bedienungsanleitung

Hoover

Hoover SteamVac F5865-900 Bedienungsanleitung

Hoover

Hoover Quick & Light Bedienungsanleitung

Hoover

Hoover 5002 Hercules Bedienungsanleitung

Hoover

Hoover HSV87-LX1-ID Bedienungsanleitung

Hoover

Hoover FH40010B Bedienungsanleitung

Hoover

Hoover SPRINT BAGLESS TSU2001 Bedienungsanleitung

Hoover

Hoover PUREPOWER Bedienungsanleitung

Hoover

Hoover UH40080 Bedienungsanleitung

Hoover

Hoover Turbo EmPower 4600 U5268900 Bedienungsanleitung

Hoover

Hoover TurboPOWER Bedienungsanleitung

Hoover

Hoover Robocom 2 Bedienungsanleitung

Hoover

Hoover F6212900 Bedienungsanleitung

Hoover

Hoover SteamVac V2 Bedienungsanleitung

Hoover

Hoover TurboPOWER Bedienungsanleitung

Hoover

Hoover Stick Cleaner S2535 Bedienungsanleitung

Hoover

Hoover Syrene Bedienungsanleitung

Hoover

Hoover CleanSlate FH14020V Bedienungsanleitung

Hoover

Hoover S3865 - Platinum Cyclonic Bagless Canister Vacuum... Bedienungsanleitung

Beliebte Staubsauger Handbücher anderer Marken

Bissell

Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung

Panasonic

Panasonic MC-YL637S147-AE Bedienungsanleitung

NEFF

NEFF N17XH10 0 Series Bedienungsanleitung

LG A9 Series Bedienungsanleitung

Oreck

Oreck Cordless Captura BK51700 Series Bedienungsanleitung

Kogan

Kogan KAVACROBVWA Bedienungsanleitung

Kränzle

Kränzle VENTOS 50 ID Benutzerhandbuch

EVVO

EVVO Ai35 Bedienungsanleitung

DeWalt

DeWalt DWH200D Bedienungsanleitung

Pontec

Pontec Pondomatic Vacuum Cleaner Bedienungsanleitung

Cleanmaxx

Cleanmaxx PC-P007E Bedienungsanleitung

Exido

Exido 240-114 Bedienungsanleitung

RIDGID

RIDGID WD1685AU0 Bedienungsanleitung

Ezviz

Ezviz RE4P Bedienungsanleitung

STG global

STG global TANVAC HDV3000 Bedienungsanleitung

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Bedienungsanleitung

Factory

Factory M3340 Bedienungsanleitung

Shop-Vac

Shop-Vac VN92 SERIES Bedienungsanleitung