HP RP9 Compact Stand Bedienungsanleitung

Installation Instructions

HP RP9 Compact

Stand

The information contained herein is subject to change without

notice.

Printed in

Second Edition: February 2016

First Edition: February 2016

*844016-002*

844016-002

Before you begin

1. Save all files and shut down the computer properly

through the operating system, and then turn off any

external devices.

2. Disconnect the power cord from the AC outlet, and

disconnect all cables from the rear of the computer.

WARNING! To avoid the risk of serious injury or

damage to the system, ensure that the power cord

is unplugged from the AC outlet at the wall before

installing this product. Failure to do so may expose

you to the risk of electric shock.

NOTE: For regulatory and safety notices, refer to

the Product Notices included with your product.

Product support

For the online access to technical support information,

self-solve tools, online assistance, community forums or

IT experts, broad multivendor knowledge base,

monitoring and diagnostic tools, go to

www.hp.com/support.

NOTE: If you need help preparing your computer model

for this installation, refer to the documentation provided

with the computer, or go to www.hp.com/support to

locate the manual for your model.

Removing the VESA plate

You may need to remove the VESA plate from the rear of the

RP9 before installing the stand. Remove the four screws

securing the VESA plate, and then remove the plate.

Installing the VESA cover

1. Select the VESA cover for your RP9 model size.

2. Angle the top section of the VESA cover toward the top

side of the stand's hinge 1, and then press the section

down onto the mounting bracket 2. Angle the bottom

section of the VESA cover toward the bottom side of the

stand's hinge 3, and then press the section down onto the

mounting bracket 4.

Installing the stand

1. Lay the RP9 face down on a flat surface covered by a soft

clean cloth.

2. Slide the tabs on the top of the stand mount into the slots

on the display head 1, and then rotate the bottom of the

stand mount down onto the display head so that it snaps

into place 2.

Routing cables

1. Connect the cables to the appropriate rear connectors.

2. Remove the cable routing cover from the neck of the

stand 1.

3. Route the cables from the connectors on the rear panel

down the neck of the stand, and then through the hole in

the center of the base 2and out the underside of the

base.

4. Replace the cable routing cover on the neck of the stand

to cover the cables 3.

18.5” RP9 model

15.6” RP9 model

Securing the stand to a countertop

1. Remove the cover from the neck of the stand 1, and then

slide the base cover forward and lift it off the base 2.

2. Fasten the stand to a countertop using the appropriate

fastening devices (not provided by HP) for your surface.

3. Slide the base cover onto the base of the stand 1, and

then replace the neck cover on the neck of the stand 2.

Adjusting the stand

Adjust the display head to the appropriate position for your

application. The suggested working angle is -5 degrees to 80

degrees.

Removing the stand

1. Lay the RP9 face down on a flat surface covered by a soft

clean cloth.

2. Push up the release latch on the rear of the display head

1, tilt the stand back 2, and then lift the stand from the

display head 3.

Documentation feedback

HP is committed to providing documentation that meets your

needs. To help us improve the documentation, please send any

suggestions, comments, or errors to [email protected].

Include the document title and part number (located near the

barcode) when submitting your feedback.

Inhaltsverzeichnis

Andere HP Rack & Stand Handbücher

HP 6400/8400 Bedienungsanleitung

HP TFT7600 G2 Bedienungsanleitung

HP 245161-B22 - 10642 42U Rack Shock Pallet Gebrauchsanweisung

HP 669048-009 Bedienungsanleitung

HP D7171A - NetServer - LPr Bedienungsanleitung

HP MCS 5042 Bedienungsanleitung

HP HP 10000 G2 Series Bedienungsanleitung

HP Rack System/E Bedienungsanleitung

HP Intelligent Series Bedienungsanleitung

HP Dual Hinge Notebook Stand Technisches Datenblatt

HP P5389A - Intel Pentium III-S 1.4 GHz Processor... Bedienungsanleitung

HP System/E41 Bedienungsanleitung

HP Quick Release EM870AA Gebrauchsanweisung

HP TS5220 Installationsanleitung

HP HP 10000 G2 Series Bedienungsanleitung

HP 158222-B21 - StorageWorks Fibre Channel SAN Switch... Bedienungsanleitung

HP Retail Mobile POS Case Bedienungsanleitung

HP 11000 G2 series Bedienungsanleitung

HP StorageWorks 1000 - Modular Smart Array Bedienungsanleitung

HP StorageWorks SSL1016 Bedienungsanleitung

HP Proliant DL580 Bedienungsanleitung

HP AT-BT10 Bedienungsanleitung

HP DESKJET 350 Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung