HP J1530C Bedienungsanleitung

HP J1530C Rack Kit for

rp74xx/rx76xx/SEU

Servers

Installation Instructions

Kit contents

WARNING: Do not mount this rack integration

kit in a rack with sectional columns, such as the

HP 5642 rack.

If any of the following items are missing or damaged, contact

your HP authorized reseller. The following hardware pieces

are included in this kit.

Quantity Description Picture

1 Cable management arm

(5069-6366)

1 Slide, left

(A6434-04045)

1 Slide, right

(A6434-04046)

3 Cable tie

(1400-3011)

2 Mounting bracket and spring

(5069-6363)

2 Actuator bracket

(5003-0540)

1 Long rod, 17U

(5003-0538)

1 Short rod, 17U

(5003-0541)

1 Long rod, 10U

(5003-0539)

1 Short rod, 10U

(5003-0542)

1 Installation instructions

The information contained herein is subject to change without notice. The

only warranties for HP products and services are set forth in the express

warranty statements accompanying such products and services. Nothing

herein should be construed as constituting an additional warranty. HP shall

not be liable for technical or editorial errors or omissions contained herein.

Part Number 391342-004

April 2007 (Fourth Edition)

Hardware contents

Identification Quantity Description Picture

A4 M4 hex lock nut

(0535-0076)

B 18 M5 x 16-mm

screw

(0515-3019)

C 6 M4 x 6-mm

screw

(0515-4500)

D 18 M5 barrel nut

(0590-2318)

E 2 10–24 custom

nut

(A6093-00180)

F 2 M4 x 10-mm flat-

head screw

(0515-4499)

J 3 M4 x 8-mm

screw

(0515-0433)

H 18 M5 cage nut

(353039-002)

Required tools

•T-20 Torx driver

•T-25 Torx driver

•8-mm hex-nut driver

Rack warning

WARNING: To reduce the risk of personal injury or

damage to the equipment, be sure that:

•The leveling feet are extended to the floor.

•The full weight of the rack rests on the leveling

feet.

•The stabilizin

feet are attached to the rack if it is

a single-rack installation.

•The racks are coupled together in multiple-rack

installations.

•Only one component is extended at a time. A

rack may become unstable if more than one

component is extended for any reason.

Anti-tip stabilizers

The anti-tip stabilizers provide stability and support when

equipment is installed, removed, or accessed within the rack.

Stabilizer kits are available in both 600-mm (23.62-in) and

800-mm (31.50-in) versions. Use the side feet provided with

these kits to stabilize stand-alone racks. If you are stabilizing

racks that are secured together with baying kits, the side feet

are optional on either end of the row.

Single racks with a mounted component exceeding 99.79 kg

(219.99 lb) do not require a stabilizer kit to be installed.

However, when extending a heavy unit for service, a kit is

recommended.

Single racks bolted to the floor or rack rows with four or more

bayed racks do not need a stabilizer kit installed.

Lift and lift handles

WARNING: If you are going to use a lift, be sure to

use a lift that can handle the load of your server. Do

not manually lift the server to install it. If a lift is not

available, use lift handle kit (A6752-04049).

Item Reference Part number

1 Lift handle panel (l) A6752-04045

2 Lift handle panel (r) A6752-04048

Item Reference Part number

3 Storage bracket A6752-00114

Installing servers into round-

hole racks

1. Attach barrel nuts to the front columns.

Item Reference

1 Product outline

2 Positions for mounting the product (refer to step 8)

3 Positions for mounting the front of the slides (refer to step

2. Attach barrel nuts to the rear columns.

Item Reference

1 Product outline

2 Positions for mounting the cable management arm (refer

to step 7)

3 Positions for mounting the rear of the slides (refer to step

NOTE: Single racks with a mounted component

exceeding 99.79 kg (220.99 lb) do not require a

stabilizer kit to be installed. However, when

extending a heavy unit for service, a kit is

recommended.

Single racks bolted to the floor or rack rows with

four or more bayed racks do not need a stabilizer kit

installed.

Item Reference

1 Stabilizer anti-tip feet

3. Install the right and left slides into the rack.

4. Choose one of the following options:

oIf you have a lift kit, place the server on the slides,

and then go to step 6.

oIf you do not have a lift kit, then go to step 5.

WARNING: The wei

ht of this product requires a lift

to install. If a lift is not available, go to step 5 for

installation of lift handle panels. If lift handles are

already installed, continue to step 6.

CAUTION: This server must be unpacked in an ESD

safe environment. Observe all ESD safety

precautions before attemptin

this procedure. Failure

to follow ESD safety precautions can result in

damage to the server.

5. Install the lift handles, and place the server on the slides.

WARNING: Use the following procedure only if a

lift is not available. This procedure should only be

attempted by two authorized HP service personnel,

as a fully loaded server can weigh up to 99.79 kg

(220 lb). Before attempting this procedure, HP

recommends that you first remove all cell boards and

AC power supplies. Instructions for removing these

components can be found in the "Removal and

replacement" chapter of the service manual. Check

with local safety regulations before attempting to

move the system using the lift handle panels. Failure

to observe these precautions can cause harm to

personnel, or damage to the equipment.

6. Secure the slides to the server.

7. Install the cable management arm.

a. Attach screws (B) to the left rear column.

b. Slip the cable management arm over the screws (B)

and tighten.

c. Extend the cable management arm to the left rear

side of the product.

d. Attach the cable management arm to the studs, and

secure it with nuts (E).

8. Install the bezel front.

9. Install the interlock device.

NOTE: If the rack is bolted to the floor or is used in

a rack configuration with at least four bayed racks,

then the interlock device is not necessary. If two

products are installed and the rack depth is no more

than 717.55 mm (28.25 in), the interlock device

can be installed so that you can remove one product

at a time.

NOTE: The products must be racked adjacent to

each other to use the interlock device.

NOTE: If four products are installed in the rack and

interlock devices are used, then two interlock devices

are needed, with one device connected to the

bottom two products, and the other device

connected to the top two products.

Item Reference

1 Second product

2 First mounting holes for second product

3 First product

10. Install the rods as shown in the following figure.

Installing servers into square-

hole racks

1. Attach cage nuts (H) to the front columns.

Item Reference

1 Product outline

2 Positions for mounting the product (refer to step 9)

3 Positions for mounting the front of the slides (refer to step

2. Attach cage nuts (H) to the rear columns.

Item Reference

1 Product outline

2 Positions for mounting the cable management arm (refer

to step 8)

3 Positions for mounting the rear of the slides (refer to step

3. Adjust the slides according to the guidelines in the

following table.

Item Measurements required for rack

1 465 mm (18.31 in)

Item Measurements required for rack

2 476.2 mm (18.75 in)

3 711 to 774.7 mm (28 to 30.5 in)

4. Install the right and left slides into the rack.

NOTE: Single racks with a mounted component

exceeding 99.79 kg (220.99 lb) do not require a

stabilizer kit to be installed. However, when

extending a heavy unit for service, a kit is

recommended.

Single racks bolted to the floor or rack rows with

four or more bayed racks do not need a stabilizer kit

installed.

5. Choose one of the following options:

oIf you have a lift kit, place the server on the slides,

and then go to step 7.

oIf you do not have a lift kit, then go to step 6.

WARNING: The wei

ht of this product requires a lift

to install. If a lift is not available, go to step 6 for

installation of lift handle panels. If lift handles are

already installed, continue to step 7.

CAUTION: This server must be unpacked in an ESD

safe environment. Observe all ESD safety

precautions before attemptin

this procedure. Failure

to follow ESD safety precautions can result in

damage to the server.

6. Install the lift handles, and place the server on the slides.

WARNING: Use the following procedure only if a

lift is not available. This procedure should only be

attempted by two authorized HP service personnel,

as a fully loaded server can weigh up to 99.79 kg

(220 lb). Before attempting this procedure, HP

recommends that you first remove all cell boards and

AC power supplies. Instructions for removing these

components can be found in the "Removal and

replacement" chapter of the service manual. Check

with local safety regulations before attempting to

move the system using the lift handle panels. Failure

to observe these precautions can cause harm to

personnel, or damage to the equipment.

7. Secure the slides to the server.

8. Install the cable management arm.

a. Attach screws (B) to the left rear column.

b. Slip the cable management arm over the screws (B)

and tighten.

c. Extend the cable management arm to the left rear

side of the product.

d. Attach the cable management arm to the studs, and

secure it with nuts (E).

Inhaltsverzeichnis

Andere HP Rack & Stand Handbücher

HP 158222-B21 - StorageWorks Fibre Channel SAN Switch... Bedienungsanleitung

HP DL320s - ProLiant 9TB SATA Storage Server... Bedienungsanleitung

HP Rack System/E Bedienungsanleitung

HP Dual Monitor Stand Technisches Datenblatt

HP D7171A - NetServer - LPr Bedienungsanleitung

HP Intelligent Series Bedienungsanleitung

HP 355 Bedienungsanleitung

HP HP 10000 G2 Series Bedienungsanleitung

HP Z600 - Workstation - 6 GB RAM Bedienungsanleitung

HP A4838A Bedienungsanleitung

HP E1586A Bedienungsanleitung

HP 11000 G2 series Bedienungsanleitung

HP 245161-B22 - 10642 42U Rack Shock Pallet Bedienungsanleitung

HP TS5220 Installationsanleitung

HP HP 10000 G2 Series Bedienungsanleitung

HP Quick Release EM870AA Gebrauchsanweisung

HP Model 745 - VME Workstation Bedienungsanleitung

HP 11000 G2 series Bedienungsanleitung

HP LaserJet Enterprise 600 Bedienungsanleitung

HP RP9 Compact Stand Bedienungsanleitung

HP BT861AA Bedienungsanleitung

HP AT-BT10 Bedienungsanleitung

HP 245161-B22 - 10642 42U Rack Shock Pallet Gebrauchsanweisung

HP StorageWorks SSL1016 Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung