HP Model 745 - VME Workstation Bedienungsanleitung



Rack Mount Kit Installation Note

For Models 745/132L and 748 Industrial Systems

Notices

Information

in this Note is subject to change without notice.

Hewlett-Packard makes no warranty of any kind about this manual, including, but not limited to, the implied warranties of mer

chantability and fitness for a particular purpose. Hewlett-Packard shall not be liable for errors contained herein or

direct, indirect, special, incidental or consequential damages about the furnishing, performance, or use of this material.

Warranty

A copy of the specific warranty terms applicable to your Hewlett-Packard product and replacement parts can be obtained from your

local Sales and Service Of

fice.

Hewlett-Packard Company 1993, 1997, 1998

This Note contains information which has been protected by copyright. All rights are reserved. Reproduction, adaptation, or

translation without prior written permission is prohibited, except as allowed under the copyright laws.

Safety Precautions

CAUTION:

Use

of the HP E3664A Rail Kit is r

equir

ed for safe rack mounting.

Multiple units stacked

directly

on top of each other r

equir

e only one rail kit on the bottom–most unit.



If the system will be installed in a closed or multi–unit rack, ensure the ambient temperature does not

exceed 55



C (131

F).



Ensure the airflow is suf

ficient for safe operation of the system.



Mount the system in such a way to prevent a hazardous condition due to uneven loading.



Do not connect the system’

s power cord to a power extension strip.

Shut down the application and operating system, then turn of

f the system at both the front panel pushbutton and the power supply

switch. Remove the interface cables and power cord(s) before installing this rack mount kit.

ARNING: Get two people to help you hold the system in position while installing it. A fully configur

ed Model 745 weighs

over 27 Kg (60 pounds); a fully configurted 748 weighs over 31 Kg (68 pounds).

Parts List Installation Options

Item

4U Flange

4U Spacer

7U Spacer

Flange screw

Dress screw (with

745

Part Number

A2261–00037

A2261–00039

A2261–00040

0515–1114

0570–1366

0590–0804

nylon washer)

Clip nut

all Mount

our installation may require dif

ferent dress

screws and clip nuts.

Qty.

Rack Mount

Mast Mount

Back

Front

Out

748

Qty.

7U Flange

A4500–000092

Dress screw (with

0570–1597

nylon washer)

745

and 748

748 only 748 only

Mast Installation

ou may want to remove the feet.

235.0 mm

EIA

Standard rack mount for Model 748.

Figure 1.

465.5 mm

Rack Installation

Figure 2 for Model 748 Front Out.

Model 748 ONLY

EIA

Standard rack mount for Model 745.

101.6 mm

465.5 mm

Figure 3 for Model 745 Front or Back Out,

Model 748 Back Out.

Figure 1: Mast Mount (748 only)

1. Attach the

2. Install the

system in

the mast with

dress screws.

Middle holes on

side.

flange and



spacer with

flange screws.

CAUTION:

Spacer must be

outside of flange

or screws will

bind internal

modules. Get

someone to

help hold the

system for

installing it in

the mast.

Figure 2: 748 Front Out, Rack Mount

1. Peel off the

trim piece.

2. Attach the

spacer and

flange with

flange screws.

3. Install the

system

in rack with

dress screws.

Figure 3: 745 Front/Back Out, 748 Back Out,

2. Attach the

3. Install the

system in

the rack with

dress screws.

CAUTION:

Spacer must be

outside of flange

flange and

spacer with

flange screws.

or screws will

bind internal

modules. Get

someone to

help you hold

the system

for installing it

in the rack.

Rack Mount

1. Remove any

existing screws

as needed.

Wall Installation

ou may want to remove the feet.

Figures 4, 5, and 6.

235.0 mm

EIA

Standard W

all Mount for Model 748.

465.5 mm

Model 748 ONLY.

Figure 4: Removing Front Cover

1. Set the workstation upside

2. Pry side catches loose

and work front cover

off the workstation.

down, then pry the three

front cover bottom

catches loose.

Figure 5: Removing S itch Button & Light Pipe

1. Pull off the

2. Press the light pipe

power switch button,

then press the

switch arm in

to ON.

catch to the left,

then pull out the

light pipe.

Figure 6: Wall Mount

1. Attach the

spacer and

flange with

flange screws.

2. Install the

workstation to

the wall with

dress screws.

CAUTION:

Get two people

to help you hold

the workstation

to wall for

mounting.



Part Number: A2677–90011

Printed in U.S.A.

Edition E0698



Andere Handbücher für Model 745 - VME Workstation

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere HP Rack & Stand Handbücher

HP RP9 Compact Stand Bedienungsanleitung

HP Retail Mobile POS Case Bedienungsanleitung

HP 11000 G2 series Bedienungsanleitung

HP ML110 - ProLiant G5 2TB Storage Server NAS Bedienungsanleitung

HP BT861AA Bedienungsanleitung

HP Proliant DL580 Bedienungsanleitung

HP Tc4100 - Server - 256 MB RAM Bedienungsanleitung

HP 245161-B22 - 10642 42U Rack Shock Pallet Bedienungsanleitung

HP HP 10000 G2 Series Bedienungsanleitung

HP Z600 - Workstation - 6 GB RAM Bedienungsanleitung

HP MCS 5042 Bedienungsanleitung

HP StorageWorks SSL1016 Bedienungsanleitung

HP ProCurve 6600-48G-4XG Bedienungsanleitung

HP TS5220 Installationsanleitung

HP Rack System/E Bedienungsanleitung

HP D7171A - NetServer - LPr Bedienungsanleitung

HP 11000 G2 series Bedienungsanleitung

HP 158222-B21 - StorageWorks Fibre Channel SAN Switch... Bedienungsanleitung

HP DL320s - ProLiant 9TB SATA Storage Server... Bedienungsanleitung

HP Integrated Work Center Stand Gebrauchsanweisung

HP 669048-009 Bedienungsanleitung

HP HP 10000 G2 Series Bedienungsanleitung

HP Quick Release EM870AA Gebrauchsanweisung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung