HP DL320s - ProLiant 9TB SATA Storage Server... Bedienungsanleitung

HP StorageWorks

Storage server 2U fixed rail in-

stallation instructions

This document provides procedures for installing a 2U-

size storage server into a rack using fixed rails (non-

sliding). HP assumes that you are qualified in servicing

computer equipment, and trained in recognizing haz-

ards in products with hazardous energy levels.

First edition (February 2007)

The information in this document is subject to change without notice.

Printed in the US

www.hp.com

*440929-001*

Rail hardware

Rail pins3Right rail assembly1

Left rail assembly2

WARNING!

Before you begin, make sure that the rack is sufficiently stable.

If provided, lower the rack leveler feet and make sure any re-

quired stabilizers are installed. If provided, extend the rack anti-

tip device. Failure to extend the anti-tip device could result in

personal injury or damage if the rack tips over.

Install the rails in the rack

NOTE:

If the holes in the rack uprights are round instead of square, re-

move the standard pins from the rails and replace them with the

round-hole pins provided with the rail kit. The pins are load-

bearing. Do not remove the standard pins except to replace

them with the pins for round-hole racks.

1. Identify the left (L) and right (R) rack rails by markings stamped into

the rails.

2. Insert the rear end of the right rack rail into the inside back of the

rack until the pins extend through the holes in the rack upright.

Squeeze the scissor-type locking latch to enable the latch and pins

to extend through the rack holes.

CAUTION:

Be sure that the scissor-type locking latch engages when

the end of the rail seats into the rack uprights.

3. Extend the front end of the rail toward the inside front of the rack.

Pull the safety latch to release the scissor-type lock latch and squeeze

the scissor-type latch together to insert the rail and pins through the

rack upright holes until the latch engages.

4. Loosen the locking nut on the shipping retaining bracket and slide

the bracket to the farthest position on the rear of the rail.

5. Repeat the above steps for the left rack rail.

Install the server in the rack

1. Align the server with the rails and slide it into the rack.

2. Slide the server until the front edge is flush with the front of the rack

(1).

3. Pull off the storage server side covers to expose the thumbscrews on

each side.

4. Secure the server to the front of the rack using the thumbscrews (2).

5. Reattach the storage server side covers.

Secure the server in the rack

1. With the locking nut loose (1), slide the retaining bracket toward

the server until the tab engages the slot in the server chassis (2).

2. Tighten the locking nut on the bracket.

3. Repeat these steps for the other rail.

HP StorageWorks

Storage server 2U fixed rail in-

stallation instructions

This document provides procedures for installing a 2U-

size storage server into a rack using fixed rails (non-

sliding). HP assumes that you are qualified in servicing

computer equipment, and trained in recognizing haz-

ards in products with hazardous energy levels.

First edition (February 2007)

The information in this document is subject to change without notice.

Printed in the US

www.hp.com

*440929-001*

Rail hardware

Rail pins3Right rail assembly1

Left rail assembly2

WARNING!

Before you begin, make sure that the rack is sufficiently stable.

If provided, lower the rack leveler feet and make sure any re-

quired stabilizers are installed. If provided, extend the rack anti-

tip device. Failure to extend the anti-tip device could result in

personal injury or damage if the rack tips over.

Install the rails in the rack

NOTE:

If the holes in the rack uprights are round instead of square, re-

move the standard pins from the rails and replace them with the

round-hole pins provided with the rail kit. The pins are load-

bearing. Do not remove the standard pins except to replace

them with the pins for round-hole racks.

1. Identify the left (L) and right (R) rack rails by markings stamped into

the rails.

2. Insert the rear end of the right rack rail into the inside back of the

rack until the pins extend through the holes in the rack upright.

Squeeze the scissor-type locking latch to enable the latch and pins

to extend through the rack holes.

CAUTION:

Be sure that the scissor-type locking latch engages when

the end of the rail seats into the rack uprights.

3. Extend the front end of the rail toward the inside front of the rack.

Pull the safety latch to release the scissor-type lock latch and squeeze

the scissor-type latch together to insert the rail and pins through the

rack upright holes until the latch engages.

4. Loosen the locking nut on the shipping retaining bracket and slide

the bracket to the farthest position on the rear of the rail.

5. Repeat the above steps for the left rack rail.

Install the server in the rack

1. Align the server with the rails and slide it into the rack.

2. Slide the server until the front edge is flush with the front of the rack

(1).

3. Pull off the storage server side covers to expose the thumbscrews on

each side.

4. Secure the server to the front of the rack using the thumbscrews (2).

5. Reattach the storage server side covers.

Secure the server in the rack

1. With the locking nut loose (1), slide the retaining bracket toward

the server until the tab engages the slot in the server chassis (2).

2. Tighten the locking nut on the bracket.

3. Repeat these steps for the other rail.

Andere Handbücher für DL320s - ProLiant 9TB SATA Storage Server...

Dieses Handbuch passt für folgende Modelle

Andere HP Rack & Stand Handbücher

HP P5389A - Intel Pentium III-S 1.4 GHz Processor... Bedienungsanleitung

HP TS5220 Installationsanleitung

HP Retail Mobile POS Case Bedienungsanleitung

HP Dual Monitor Stand Technisches Datenblatt

HP 245161-B22 - 10642 42U Rack Shock Pallet Gebrauchsanweisung

HP Quick Release EM870AA Gebrauchsanweisung

HP 158222-B21 - StorageWorks Fibre Channel SAN Switch... Bedienungsanleitung

HP TFT7600 G2 Bedienungsanleitung

HP cc2300 Bedienungsanleitung

HP MCS 5042 Bedienungsanleitung

HP 11000 G2 series Bedienungsanleitung

HP E1586A Bedienungsanleitung

HP LaserJet Enterprise 600 Bedienungsanleitung

HP ProCurve 6600-48G-4XG Bedienungsanleitung

HP Model 745 - VME Workstation Bedienungsanleitung

HP ML110 - ProLiant G5 2TB Storage Server NAS Bedienungsanleitung

HP RP9 Compact Stand Bedienungsanleitung

HP 6400/8400 Bedienungsanleitung

HP System/E41 Bedienungsanleitung

HP D7171A - NetServer - LPr Bedienungsanleitung

HP BT861AA Bedienungsanleitung

HP StorageWorks 1000 - Modular Smart Array Bedienungsanleitung

HP Dual Hinge Notebook Stand Technisches Datenblatt

HP 355 Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung