HRS BNC75 Series Handbuch

2022.01

RF-21038

The specification and contents are subject to change without notice. Please check the latest document.

Mounting / Soldering procedure

for BNC 12G connectors

Hirose electric RF engineering team

RF-21038

Jan./2022

Products ：BNC(75)-PLR-PC(D)-12G-3

CL302-0088-0-00

2022.01

RF-21038

The specification and contents are subject to change without notice. Please check the latest document. 2

Mounting and soldering procedure

Positioning to a chassis and a PCB

※Before soldering, a connector should be properly positioned to its chassis and

PCB in order not to make any stress on the soldering area after soldering.

Order 1. Positioning ⇒2. Outer contact soldering ⇒3. Center contact soldering

A M2(mm) screw can be used for the

temporally fixing. No need to use this

screw depending on your situation.

No gap between a connector

and a PCB

1. Connector positioning for PCB ※Fluxing

Note

Far excessive amount of

flux left at the designated

area on the picture could

affect its high frequency

performance.

Fluxing area: 4 Soldering areas of outer contacts and a

soldering area of a center contact.

NOTE: A soldered connector must be used after cooled to the operating temperature.

2022.01

RF-21038

The specification and contents are subject to change without notice. Please check the latest document. 3

2. Outer contact soldering

Heat both a PCB pad and a connector contact

so that pour solder into a through hole properly.

GOOD A through

hole(TH) is

fulfilled with

solder. Defect

Lack of

solder

- Wave soldering condition

Preheat : max 100C / max 120sec

Solder : max 245C/ max 5sec

- Hand soldering condition

Preheat : max 100C / max 120sec

Solder iron : max 380C/ max 5sec

Note : reflow soldering can’t be

applied for this connector because of

outer shell swellings.

3. Center contact soldering

Around Dia0.3mm solder suits for center contact soldering.

Excessive soldering criteria

Solder should be in the pad area. Far

excessive solder could cause RF

performance.

Soldering at

bottom area

Soldering Criteria

Mounting and soldering procedure

Order 1. Positioning ⇒2. Outer contact soldering ⇒3. Center contact soldering

NOTE: A soldered connector must be used after cooled to the operating temperature.

Solder should be under the soldering

area. Far excessive solder could cause

RF performance.

Dieses Handbuch passt für folgende Modelle

Andere HRS Kabel und Steckverbinder Handbücher

HRS

HRS DF57 Series Bedienungsanleitung

HRS

HRS BM20 Series Bedienungsanleitung

HRS

HRS DF51-6EP-2C Bedienungsanleitung

HRS

HRS FH67 Series Bedienungsanleitung

HRS

HRS GT50 Series Bedienungsanleitung

HRS

HRS DF51 Series Bedienungsanleitung

HRS

HRS Hirose IT3 Kurzanleitung

HRS

HRS EM30MSD Series Bedienungsanleitung

HRS

HRS ZE05 Series Bedienungsanleitung

HRS

HRS BM25 Series Bedienungsanleitung

HRS

HRS DF63 Series Bedienungsanleitung

HRS

HRS SignalBee DF13 Series Bedienungsanleitung

HRS

HRS FH12 Series Bedienungsanleitung

HRS

HRS DF40 Series Bedienungsanleitung

HRS

HRS ZE064W Series Bedienungsanleitung

HRS

HRS ZH05 Series Bedienungsanleitung

HRS

HRS DF63W Series Handbuch

HRS

HRS HIF Series Bedienungsanleitung

HRS

HRS DF62W Series Bedienungsanleitung

HRS

HRS GT36A Bedienungsanleitung

HRS

HRS FH12-20S-0.5SH(54) Bedienungsanleitung

HRS

HRS DF57H S-1.2C Series Bedienungsanleitung

HRS

HRS DF62W EP 2.2C Series Bedienungsanleitung

HRS

HRS FH29 Series Bedienungsanleitung

Beliebte Kabel und Steckverbinder Handbücher anderer Marken

Philips

Philips SWA6310 Bedienungsanleitung

StarTech.com

StarTech.com CRJ4550PK Bedienungsanleitung

Nohau

Nohau EMUL-IP2K-PC Bedienungsanleitung

Foxun

Foxun SX-SP144E-HD4K2K Bedienungsanleitung

Philips

Philips SWA3305W Bedienungsanleitung

opticis

opticis Stretch DVIM1-1P0x Bedienungsanleitung

Volkswagen

Volkswagen VAS 6558A Bedienungsanleitung

NEXIBO

NEXIBO N-13 Bedienungsanleitung

CYP

CYP PU-1H3HBTL Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1784-u2dhp Bedienungsanleitung

Global Caché

Global Caché Flex Link Blaster Bedienungsanleitung

Hauppauge

Hauppauge USB-Live2 Bedienungsanleitung

Fenix

Fenix MPSV 15 Bedienungsanleitung

BEGA

BEGA 71 085 Bedienungsanleitung

Tesla

Tesla HPWC Bedienungsanleitung

GAMERON

GAMERON LUXURY TV CABLE Bedienungsanleitung

molex

molex Milli-Grid Dual row 87568 Series Bedienungsanleitung

Burndy

Burndy Continental Industries thermOweld CRE-7 Bedienungsanleitung