HUANUO HNWDS1 Bedienungsanleitung
1
Monitor Wall Mount
Instruction Manual
Model:HNWDS1
Thank you for choosing this HUANUO product! At HUANUO
we strive to provide you with the best quality products and
services in the industry. Please share your experience of our
product with others at www.huanuoav.com/reviews if you
are satisfied. Should you have any issues, please don't
hesitate to contact us.
Technical Support:
1-800-556-0533 Mon-Fri 10am - 5pm (PST) (USA) (CAN)
Other Info:
[email protected] (US/CA)
Website:
www.huanuoav.com
Check the VESA Pattern of Your Monitor beforeYouBegin the Installation
• Please carefully read all instructions before attempting installation. If you do not understand the
instructions or have any concerns or questions, please contact our customer service at
CAUTION: Avoid potential personal injuries and property damage!
• This product is designed for use in wood stud, solid concrete, concrete block and brick walls -
DO NOT install into drywall alone.
• Do not use this product for any purpose that is not explicitly specified in this manual. Do not
exceed weight capacity. We are not liable for damage or injury caused by improper mounting,
incorrect assembly or inappropriate use.
• This product contains a high pressure gas spring, fire and percussion prohibited. Also it is strictly
prohibited to dismantle without professionals. Please return to the manufacturer or hand over to
professional agencies if the product is abandoned.
• The wall must be capable of supporting three times the weight of the total load (the mount, the
monitor and all accessories weight).
IMPORTANT SAFETY INFORMATION
If this mount is NOT compatible, please contact customer service
If your Monitor VESA is greater than 100x100 mm/4x4 in. or less than
VESA 75x75mm/3x3in., this mount is NOT compatible.
Weight Restrictions
4.4-17.6 lbs.
(2-8 kg)
DO NOT exceed the maximum weight indicated.
This mounting system is intended for use only within
the maximum weights indicated. Use with products
heavier than the maximum weights indicated may
result in failure of the mount and its accessories,
causing possible damage and or injury.
WARNING
If your monitor weighs
more,this mount is NOT
compatible.
75 mm ≈ 3 in.
100 mm ≈ 4 in.
Minimum VESA pattern:
75mm/3 in.(W)x75mm/3 in.(H)
MAX:100
mm/4 in.
MAX:100
mm/4 in.
MAX:100
mm/4 in.
Warning!
Do not adjust tension without monitor.
1. Ensuremonitorhas been attached to the mount.
2. Read your monitor box or manual to find out monitor net weight.
3. Ensurethe net weight of monitor (including accessories) is within
4.4-17.6 Ibs (2-8 kg).
Clockwise to reduce
tension(carry less weight)
Counter-clockwise to increase
tension(carry more weight)
TENSION ADJUSTMENT SHOULD BE DONE ONLY
AFTER MOUNT INSTALLATION
Adjustment Sign
[02]
888
6
M6.3x55mm M10x45mm
M5mm
8
Monitor Plate
Bolt Bolt
Screw
Tools Neede (Not Included)
Phillips
CD
Bolt
Supplied Parts and Hardware for Step 1
Supplied Parts and Hardware for Step 2
Supplied Hardware for Step 3 and Step 5
5/32 in.(4mm)
Wood Drill
3/8 in.(10mm)
Concrete Drill
M-E(x2)
[01]
Large Allen Key
15/64 in.(6mm)
M-F1(x1)
Small Allen Key
5/32in.(4mm)
M-F2(x1)
[01]
[01]
[01]
2 11/64 in.(55mm)
5/32 in.
(4mm)
screws
. Drill 3 pilot holes using a 5/32 in.(4mm) diameter
drill bit. Make sure the depth is not less than 2 11/64 in.(55mm).
B
B
1a.Wood Stud Option
[01]
[01]
[01] [01]
Drill 3 pilot holes using a 3/8 in.(10mm) diameter drill bit. Make
sure the depth is not less than 2 23/64in.(60mm）
(2 23/64in.)
3/8in.)
screws
B
C
BC
1b.Solid Concrete or Concrete Block Option
[01]
[01]
[01]
Bolt length: Verify adequate thread engagement with bolts or bolts/spacers
combination. We recommend thread engagement by at least 5 turns.
-Too short will not hold the monitor.
-Too long will damage the monitor.
Too Long
Correct Correct
Too Short
M-C
2. Attach the Monitor Plates to the Monitors
M-F1 (Large Allen Key)
[02]
[02]
3. Secure the Monitors to Arms
Round
M-D
M-C
M-F1 (Large Allen Key)
M-E
Be sure to keep the arm in horizontal
position during adjustment. Or else, it
would be difficult to adjust the mount
or damage the mount.
1. If the monitor can stay at the desired height by itself, no adjustment needed.
2. If the monitor rises up, press the arm to keep it in horizontal position and then
use the
Allen Key (M-F1)
to turn the bolt clockwise(“-” direction) to reduce
tension of the arm only until the monitor can stay at the desired height by itself.
3. If the monitor falls down, lift the arm to keep it in horizontal position and then
use the
Allen Key
(M-F1)
to turn the bolt counter-clockwise (“+” direction) to
increase tension of the arm only until the monitor can stay at the desired height
by itself.
4. Adjust Gas Spring Tension
M-F1 (Large Allen Key)
1. Slightly loosen both tilts bolts [T].
2. Adiust monitors to your desired tilt angle.
3. Retighten both tilt bolts [T] to fix the tilt angle.
6. Route the Cables along the Arms
5. Adjust the Tilt Angle
M-F2 (Small Allen Key)
Inhaltsverzeichnis
Andere HUANUO Rack & Stand Handbücher
HUANUO
HUANUO HADSK5 Bedienungsanleitung
HUANUO
HUANUO HNLL11 Bedienungsanleitung
HUANUO
HUANUO HNCM9 Bedienungsanleitung
HUANUO
HUANUO HNWSS1 Bedienungsanleitung
HUANUO
HUANUO HACM1 Bedienungsanleitung
HUANUO
HUANUO HNDS6 Bedienungsanleitung
HUANUO
HUANUO HNCM9 Bedienungsanleitung
HUANUO
HUANUO HNFO2 Bedienungsanleitung
HUANUO
HUANUO HNDS11 Bedienungsanleitung
HUANUO
HUANUO HNLL3 Bedienungsanleitung
HUANUO
HUANUO HNDSK4 Bedienungsanleitung
HUANUO
HUANUO HNTS3S Bedienungsanleitung
HUANUO
HUANUO HNDS7 Bedienungsanleitung
HUANUO
HUANUO HNPS01 Bedienungsanleitung
HUANUO
HUANUO HNCM2 Bedienungsanleitung
HUANUO
HUANUO HNHM4 Bedienungsanleitung
HUANUO
HUANUO HNPS02 Bedienungsanleitung
HUANUO
HUANUO HNCM20 Bedienungsanleitung
HUANUO
HUANUO HNMS02 Bedienungsanleitung
HUANUO
HUANUO HNCM18 Bedienungsanleitung
Beliebte Rack & Stand Handbücher anderer Marken
Salamander
Salamander Acadia AC/W/L400/WH Bedienungsanleitung
Fohhn
Fohhn VAT-09 Benutzerhandbuch
ricoo
ricoo FS0522 Bedienungsanleitung
AMSOIL
AMSOIL BMK-22 Kurzanleitung
Kargo Master
Kargo Master 48220 Bedienungsanleitung
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung
