Huawei UPS5000-E Series Bedienungsanleitung

Issue: 02

Part Number: 31500DCY

Date: 2020-11-10

UPS5000-E-(30 kVA-120 kVA)-FM

Quick Guide

1Overview

UPS Model Capacity Configuration Weight (Full

Configuration)

Dimensions (H x W

x D)

UPS5000-E-120K-FM 30 kVA, 60 kVA, 90 kVA,

120 kVA 310 kg 2000 mm x 600 mm

x 850 mm

(1) Cover

(2) Output switch

(3) Maintenance bypass switch

(4) Bypass input switch

(5) Mains input switch

(6) Surge protective module

(optional)

(7) Control module

(8) Bypass module

(9) Power modules

(10) Monitor display module (MDU)

(11) Folder

1. Before installation, read the user manual carefully to get familiar with product information

and safety precautions.

2. Use insulated tools when installing the equipment.

3. Only engineers certified by Huawei or its agent are allowed to install, commission, and

maintain the UPS. Otherwise, personal injury or equipment damage may occur, and the

resulting UPS faults are beyond the warranty scope of Huawei.

2Installing the UPS

Secured Installation

1. Determine the position for installing the

cabinet. Mark mounting holes based on

the drawings. (unit: mm)

2. Use a hammer drill to drill four holes for

installing expansion bolts and then install four

expansion bolts in the holes. Remove the bolt,

spring washer, and flat washer.

3. Slide the cabinet on its castors to the installation

position.

4. (Optional) If the castors of the UPS need to be

lifted from the ground, perform Step 1 to Step 2

in Non-Secured Installation.

5. Remove the rear panel of the cabinet, and then

open the front door.

6. Remove the four plugs from the bottom of the

cabinet (two on the front and two at the back).

7. Insert four M12x115 expansion bolts into

the expansion bolt holes in the floor, and

tighten the expansion bolts.

2. Check whether the bottom of the cabinet is

horizontal by using a level. If the cabinet is

not leveled, adjust the leveling feet.

1. Lower the four leveling feet at the bottom of

the cabinet by using a wrench until all the four

castors at the bottom hang in the air and the

leveling feet bear the whole cabinet weight.

Non-Secured Installation

3Connecting Cables

•Prepare cables away from the cabinets to prevent scraps from falling inside. Cable scraps

may ignite and cause personal injury or device damage.

•After cables have been installed, clean the cabinets in a timely manner. Keep the cabinets

and surrounding environment clean and tidy.

•You need to prepare terminals onsite. The stripped length of the copper wire should be the

same as that of the part of the terminal that covers the conductor.

UPS Cable Connection Reference

3.1

The cabling route is for reference only. Connect cables based on site requirements.

Installing Cables

3.2

1. Ensure the maintenance bypass switch is

OFF. Open the front door, remove the front

cover, and remove covers from the top of

the cabinet based on the site requirements.

2. (Skip this step if the mains input and

bypass input share a power source.)

Remove the copper bars between the

mains input and bypass input.

Scenario 1: Routing Cables from the Top

3. Connect the ground cable, power cable, and signal cable. There is no need to connect the

bypass input power cable if the mains input and bypass input share a power source.

Signal cable

Port

Description Bolt

Specifications Torque

Mains input M10 x 30 26 N•m

Bypass input M10 x 30 26 N•m

Battery input M12 x 35 46 N•m

Output M10 x 30 26 N•m

PE M10 x 30 26 N•m

The wire routed from the middle point of positive

and negative battery strings is the neutral wire.

Take a battery string consisting of 40 batteries for

example. The battery neutral wire is routed from

the middle between positive and negative battery

strings, each consisting of 20 batteries.

Scenario 2: Routing Cables from the Bottom

A cable entry cabinet needs to be installed when cables are routed from the bottom. This

document uses the cable entry cabinet installed on the right of the UPS cabinet as an example.

1. (Optional) Determine the installation

position for the cable entry cabinet, and

draw mounting holes in the installation

position based on drawings.

2. Remove the right and rear covers from the

UPS cabinet, and remove the front and rear

covers from the cable entry cabinet. Put

away the removed screws and covers.

3. Adjust the anchor bolts of the cable entry

cabinet to make it flush with the UPS cabinet.

4. Install equipotential plate mounting kits on

the same horizontal plane of the UPS cabinet

and cable entry cabinet.

5. Place the cable entry cabinet on the

right of the UPS cabinet.

6. Install the front and rear connecting kits.

7. (Optional) Secure the cable entry cabinet

to the ground.

8. Install an equipotential plate.

9. Remove covers from the top of the cable

entry cabinet based on the site requirements.

10.Remove a certain number of small covers

from the bottom of the cable entry cabinet

based on the actual cable conditions.

11.Connect ground cables and power cables.

For the screw specifications and torque used

for connecting cables in a bottom cable

routing scenario, refer to the top cable

routing scenario. This section only shows

the cable routes in the bottom cable

routing scenario.

12.Remove the signal cable trough cover

from the cable entry cabinet. 13.Connect the signal cable. (Route the signal

cable out of the UPS cabinet through the

cable hole on the top, and then into the cable

entry cabinet through the cable hole on the

top of that cabinet.)

If the cable entry cabinet is

placed on the left of the

UPS cabinet, remove the

cable trough for signal

cables and install it on the

right of the cable entry

cabinet.

4Verifying the Installation

1. Check that there is no foreign matter

at the top and bottom of the cabinet,

copper bars, switches, and the rear of

modules.

(1) Rear of modules

(2) Cabinet top

(3) Wiring terminal

blocks

(4) Switches

14.Install the right cover of the UPS cabinet on the right of the cable

entry cabinet, and install other covers in the original positions.

Dustproof cover

2. After verifying the installation, reinstall all the

covers.

3. (Remove the paper protective film from the

sealing putty.) After routing cables and

verifying cable connections, seal the gap

between cables and the cabinet using sealing

putty.

Sealing putty

Paper protective

film

Sealing putty must be used

as a whole and the gap can

be sealed only from the top.

4. Do not remove the dustproof cover

before power-on to prevent dust inside

the UPS.

5Powering On and Starting the UPS

1. Before powering on the UPS, ensure that the UPS has passed all check items in the

UPS5000

Commissioning and Acceptance Report

and Chapter 5.

2. Measure the voltage and frequency of the UPS upstream input switch. The line voltage range

is 138–485 V AC, and the frequency range is 40–70 Hz.

Powering On the UPS

5.1

Close the upstream input switch.

Close the UPS bypass input switch, output switch, and mains input switch.

After the UPS is powered on, initialization begins. The MDU displays the Huawei logo and an

initialization progress bar.

(Optional) If a surge protective module is configured, turn on its switch.

Initial Startup

5.2

Download and install the Service Expert app.

After login, tap Power-on password

activation on the screen. A message is

displayed, indicating whether to start the UPS.

Tap OK.

Insert the WiFi module into the USB port on

the MDU. Enable the mobile phone WLAN,

search for the UPS_WIFI signal, and connect to

the WiFi signal. The password is Changeme.

Set the Site and Device Type as required, and

connect the device. Set IP to 192.168.0.10, Port

to 443, Username to admin, Password to

Changeme, and click Login.

Enter Bar code and Verification code

obtained from the LCD on the Offline

Activation screen. Tap Generate PWD to

generate a startup password.

Set Site and Device Type as required,

and tap Offline Activation.

Enter the generated password in the

password textbox on the LCD to start the

UPS.

Use the app to

start the UPS

online?

Yes

No, start

the UPS

offline

On the app home screen, tap StartUp to access the Set Startup screen.

•If the UPS is powered on for the first time, you need to obtain the startup password from the

Service Expert app. Skip this step if the UPS is not powered on for the first time.

•The Service Expert app can be downloaded from Google Play Store and can run on Android.

1. Obtain the startup password.

System User LCD Preset Password WebUI Preset Password

admin (system

administrator) 000001 Changeme

operator (common user) 000001 Changeme

To ensure system security,

change the LCD and WebUI

passwords after the first login.

1. On the main menu, choose Common Functions and

tap Inv. ON.

2. In the displayed login window, enter the user name and

password, and tap .

3. In the displayed dialog box, tap Yes to start the inverter.

Starting inverter

5.3

2. Set the language, time, date, network parameters, and system parameters on the Settings

Wizard screen.

4. If the system has connected to the remote EPO switch, you need to choose Monitoring > UPS

System > Running Parameter > System Settings on the WebUI and set EPO detection to

Enable.

5. View the system running status diagram on the MDU to check that the UPS is working in

bypass mode.

3. After you perform the settings, the Bypass mode and No battery alarms are reported by

the MDU and do not need to be cleared. If there is any other alarm, you need to rectify

the fault.

Andere Handbücher für UPS5000-E Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Huawei UPS Handbücher

Huawei

Huawei UPS2000-G-6 kVA Bedienungsanleitung

Huawei

Huawei UPS5000-A-30KTTL Bedienungsanleitung

Huawei

Huawei SmartLi Series Bedienungsanleitung

Huawei

Huawei UPS5000-A-200K-ST Bedienungsanleitung

Huawei

Huawei PDU8000-0630ACV4-SCA108 Bedienungsanleitung

Huawei

Huawei UPS5000-S-600 Bedienungsanleitung

Huawei

Huawei UPS2000-H Bedienungsanleitung

Huawei

Huawei UPS5000 Bedienungsanleitung

Huawei

Huawei UPS5000-E Series Bedienungsanleitung

Huawei

Huawei UPS5000-H-1200 Series Bedienungsanleitung

Huawei

Huawei UPS5000-E-30 kVA Bedienungsanleitung

Huawei

Huawei UPS2000-G Series Bedienungsanleitung

Huawei

Huawei PDU8000 Series Bedienungsanleitung

Huawei

Huawei UPS5000-A-600K-SC Bedienungsanleitung

Huawei

Huawei UPS5000-E-400K-SM Bedienungsanleitung

Huawei

Huawei UPS5000-E Series Bedienungsanleitung

Huawei

Huawei UPS2000-G-15KRTL Bedienungsanleitung

Huawei

Huawei UPS5000-A-H Series Bedienungsanleitung

Huawei

Huawei UPS5000-A-400K-FTS Bedienungsanleitung

Huawei

Huawei UPS5000-S-600 Bedienungsanleitung

Huawei

Huawei UPS5000-A-30 kVA Bedienungsanleitung

Huawei

Huawei UPS5000-E Series Bedienungsanleitung

Huawei

Huawei UPS5000-S-880K-SM Bedienungsanleitung

Huawei

Huawei UPS5000-S Series Bedienungsanleitung

Beliebte UPS Handbücher anderer Marken

Pylontech

Pylontech Victron & Pylontech US5000 Bedienungsanleitung

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Bedienungsanleitung

Mecer

Mecer ME-1000-WTU Bedienungsanleitung

Mustek

Mustek PowerMust 530(B) Plus Installations- und Betriebshandbuch

Emerson

Emerson Liebert NXL series Bedienungsanleitung

MAKELSAN

MAKELSAN BOXER SERIES Bedienungsanleitung

Block

Block PC-0524-400-0 Bedienungsanleitung

CyberPower

CyberPower CP585LCD Bedienungsanleitung

Eaton

Eaton 3S Montageanleitung

CyberPower

CyberPower Office Tower Series UPS 1000 Bedienungsanleitung

CyberPower

CyberPower BM100 Bedienungsanleitung

Best Power

Best Power 610 Bedienungsanleitung

Best Power

Best Power Unity/I UT3K Bedienungsanleitung

Mustek

Mustek PowerMust 400 Offline Bedienungsanleitung

Xantrex

Xantrex Trace 512 UR-UPS Bedienungsanleitung

Forza

Forza SL-1501UL Bedienungsanleitung

LEGRAND

LEGRAND keor 310081 Bedienungsanleitung

ABB

ABB Conceptpower DPA 500 Bedienungsanleitung