Hunter RAIN-CLIK WR-CLIK Betriebsanleitung

WR-CLIK Wireless Rain-Clik

WRF-CLIK Wireless Rain/Freeze-Clik

Rain Sensor Shutoff for Automatic Irrigation Systems

Owner’s Manual and Installation Instructions

TABLE OF CONTENTS

Features.................................................................................................................................................................3

Wireless Rain-Clik™Components........................................................................................................................4

Mounting the Receiver.........................................................................................................................................6

Mounting the Transmitter ..................................................................................................................................10

Adjustments and Operation..............................................................................................................................11

FCC Notice..........................................................................................................................................................17

FCC Declaration of Conformity.........................................................................................................................18

Industry of Canada Notice.................................................................................................................................20

CE & Australia Notice.........................................................................................................................................21

Notes ...................................................................................................................................................................22

FEATURES

Wireless Rain-Clik™sensors attach quickly and easily to your controller. Wireless Rain-Clik™

features include:

1. Quick Response™– Unique technology that

turns off the irrigation system immediately

rather than after it has accumulated a fixed

amount of rain. No calibration is required.

2. Maintenance-Free Design – Provides trouble-

free operation for up to ten years. There are

no batteries to replace.

3. Wireless operation up to 800 ft. (275 m) –

No wires are required between the rain sensor

and controller.

4. Two models available:

Wireless Rain-Clik™(WR-CLIK) – Acts as a

switch to deactivate automatic watering of

your irrigation controller when it rains. Once

rain has stopped and the sensor has dried out,

automatic irrigation will resume.

Wireless Rain/Freeze-Clik (WRF-CLIK) – The

Wireless Rain/Freeze-Clik includes a freeze

sensor that is designed to keep the irrigation

system from operating when temperatures

drop to 37˚F or below. When temperatures rise

above 37˚F, the sensor will enable automatic

watering.

5. Automatic Synchronization – The Wireless

Rain-Clik™transmitter will send wireless

signals every hour to the receiver to assure

that the sensor and receiver are continuously

synchronized.

6. Lost Communication/Battery Status

Indication – The Sensor Bypass LED will flash

RED if the receiver has not received a signal

from the transmitter. This can indicate a low or

dead battery.

WIRELESS RAIN-CLIK™COMPONENTS

Wireless Rain-Clik™Transmitter

1. Manual Test Spindle – Press and hold

the manual test spindle to confirm proper

operation of your transmitter.

2. Vent Ring – Used to adjust the reset rate

or dry out time for the sensors. Opening

the vents will decrease the reset rate, while

closing the vents will increase the time it

takes for the discs to dry out.

3. Radio Antenna – Transmits a wireless signal

to the receiver up to

800 ft. (275m). It is

recommended that the

antenna be oriented

vertically

4. Mounting Arm – Metal extension arm for

mounting the

sensor.

5. Battery Status

LED – Used to

determine the

status of the sealed

battery. Pushing the manual test spindle will

flash the LED light indicating that the battery

is good.

Vents

WIRELESS RAIN-CLIK™COMPONENTS

Wireless Rain-Clik™Receiver

1. Bypass Button – Allows automatic or manual

watering when the sensor is active.

2. Sensor Bypass LED – Indicates when sensor

has been bypassed.

3. Sensor Status LED – Used to indicate the

status of the sensor.

4. Radio Antenna – Receives a wireless signal

from the transmitter up to 800 ft. (275m) It

is recommend that the antenna be oriented

vertically.

5. AC Power Wires – The two yellow wires

are attached to a 24 VAC source from

the controller.

6. Sensor Wires – The sensor wires are

attached to either the sensor terminals in the

controller or in-line with the valve common

wire.

Blue/White Wires (used for normally closed

sensor applications)

Blue/Orange Wires (used for normally open

sensor applications)

7. Rubber Cover – Used to protect the receiver

when mounted in outdoor locations.

White

Blue

Yellow to 24 VAC Power

Orange

SENSOR STATUS

SENSOR BYPASS

Press to bypass, press

again to re-enable

GREEN = Sensor is dry

RED = Sensor is wet

Red light indicates

sensor is bypassed

RAIN SENSOR BYPASS

Blue/White wires to normally

closed sensor terminals

Orange/White wires to normally

open sensor terminals

MOUNTING THE RECEIVER

Wiring the Receiver to Your Controller

Using the hardware supplied, mount the

receiver to the wall next to the irrigation

controller. It is recommended that the receiver

be installed away from sources of electrical

interference and metal objects to maximize

communication range. Make sure to attach

the rubber cover under the receiver when

installing the receiver in an outdoor location.

Warning: This unit is designed to be installed

in conjunction with 24 VAC circuits only. Do not

use with 110 or 220 VAC circuits.

Wiring the Receiver to a Hunter SRC

1. Attach the two yellow wires to the

AC terminals.

2. Attach the blue wire to the RS terminal.

3. Attach the white wire to the C terminal.

4. Attach the valve common wire to the

RS terminal.

O Used for normally open

sensor applications

R RS C 1ACAC 2 3

Common Wire

to all Valves

SENSOR STATUS

SENSOR BYPASS

Press to bypass, press

again to re-enable

GREEN = Sensor is dry

RED = Sensor is wet

Red light indicates

sensor is bypassed

RAIN SENSOR BYPASS

MOUNTING THE RECEIVER

Wiring the Receiver to a Hunter X-Core, Pro-C,

ICC and I-CORE

1. Remove the sensor jumper across the two

SEN terminals in the controller.

2. Attach the two yellow wires to the 24

VAC terminals.

3. Attach the blue wire to one SEN terminal and

the white wire to the other SEN terminal.

SEN

TEST

P MV

REM

SENSOR STATUS

SENSOR BYPASS

Press to bypass, press

again to re-enable

GREEN = Sensor is dry

RED = Sensor is wet

Red light indicates

sensor is bypassed

RAIN SENSOR BYPASS

Wiring the Receiver to a Hunter ACC

1. Connect the blue and white wire to any of

the four Sensor Terminal pairs (Sen 1 shown).

2. Attach yellow wires to 24VAC and COM

terminals.

3. Use features at the “Set Sensor Operation”

dial position on ACC to complete setup.

4. See ACC owner’s manual for further details.

MOUNTING THE RECEIVER

Wiring the Receiver to Other Controllers:

Normally Closed Sensor Applications

1. Attach the two yellow wires to the 24

VAC terminals.

2. Attach the blue and white wire to the sensor

terminals (if available) or in-line with the valve

common wire.

P MVC AC AC

Common Wire

to all Valves

Used for normally

open sensor

applications

SENSOR STATUS

SENSOR BYPASS

Press to bypass, press

again to re-enable

GREEN = Sensor is dry

RED = Sensor is wet

Red light indicates

sensor is bypassed

RAIN SENSOR BYPASS

MOUNTING THE RECEIVER

Normally Open Sensor Applications

A few controllers on the market require

normally open rain sensors. To attach the

receiver to this type of controller, attach the

blue and orange wire to the sensor input.

Controllers with 24 VAC Solenoids and

a Booster Pump

1. Locate the common wire to the solenoid

valves and the common wire to the pump

relay. If these two wires are connected to

the “common” terminal on the controller,

disconnect both of them.

2. Twist together these wires along with one of

the wires from the Wireless Rain-Clik™and

secure with a wire nut.

3. Attach the other wire from the Wireless Rain-

Clik™receiver to the “common” terminal on

the controller.

Normally-

Open Relay

1 2 3 4C

Solenoid

Valves

Common

Wire to All

Valves

Pump

Line-In

Line-Out (to Pump)

AC AC

SENSOR STATUS

SENSOR BYPASS

Press to bypass, press

again to re-enable

GREEN = Sensor is dry

RED = Sensor is wet

Red light indicates

sensor is bypassed

RAIN SENSOR BYPASS

Note: The pump circuit output must be 24 VAC. Do

not proceed if 115 VAC.

MOUNTING THE TRANSMITTER

Standard Mounting

Using the screws

provided with your

sensor, mount the

transmitter on any

surface where it

will be exposed

to unobstructed

rainfall, but not

in the path of

sprinkler spray. The

sensor should be

oriented upright

(as pictured), but the swivel bracket can be moved

for mounting on any angled surface. Loosen the

locknut and screw before swiveling the bracket, and

then re-tighten.

Gutter Mounting (Optional)

The sensor gutter

mount can be

purchased as an

optional accessory

for your Wireless

Rain-Clik

™

(order

p/n SGM). The

SGM allows the

transmitter to be

mounted directly

to the edge of

a gutter. Install

the SGM on the transmitter by removing the

metal extension arm supplied with your sensor

and reinstalling the SGM. Position the gutter

mount on the edge of the gutter and twist the

thumbscrew to secure it in place.

SGM

Standard Mount Gutter Mount

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Hunter Zubehör Handbücher

Hunter

Hunter WIRED RAIN-CLIK Bedienungsanleitung

Hunter

Hunter ET SYSTEM SMARTPORT Bedienungsanleitung

Hunter

Hunter Wireless Rain-Clik Bedienungsanleitung

Hunter

Hunter WFS Programmierhandbuch

Hunter

Hunter DSP700 Series Bedienungsanleitung

Hunter

Hunter Wireless Rain-Clik Bedienungsanleitung

Hunter

Hunter Hunter Accessory Table 20523 Bedienungsanleitung

Hunter

Hunter RAIN CLIK WR-CLIK Betriebsanleitung

Hunter

Hunter Solar Sync Bedienungsanleitung

Hunter

Hunter BP-01 Bedienungsanleitung

Hunter

Hunter Wireless Rain-Clik Bedienungsanleitung

Hunter

Hunter Wireless Rain-Clik Originalbetriebsanleitung

Hunter

Hunter Soil-Clik Bedienungsanleitung

Hunter

Hunter Solar Sync Bedienungsanleitung

Hunter

Hunter Rain-Clik WRC-TR Bedienungsanleitung

Hunter

Hunter MINI-CLIK Stücklistenhandbuch

Hunter

Hunter Wireless Rain-Clik Bedienungsanleitung

Hunter

Hunter LIT-293 Bedienungsanleitung

Hunter

Hunter Wireless Rain-Clik Bedienungsanleitung

Hunter

Hunter WIRED RAIN-CLIK RAIN-CLIK Stücklistenhandbuch

Hunter

Hunter Light Kit Gebrauchsanweisung

Hunter

Hunter FLOW-CLIK Betriebsanleitung

Hunter

Hunter 43758 Bedienungsanleitung

Hunter

Hunter FLOW-SYNC HFS Programmierhandbuch

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung