Hunter Soil-Clik Bedienungsanleitung

Soil-Clik®

OWNER’S MANUAL

Soil Moisture Sensor

Wired Soil-Clik Module and Probe

Sensor for Compatible Hunter Controllers

Introduction

Soil-Clik is a soil moisture system that prevents overwatering when the soil is wet. Soil-Clik is designed for

use with Hunter controllers that have normally closed smart sensor inputs, or with any AC-powered control

system by interrupting the common wire to the valves.

Module

Probe

Table of Contents

4Installation

4Choosing the Probe Location

7Installing the Probe

10 Choosing the Module Location

12 Connecting the Module to Hunter Products

12 Overview

13 ACC

13 ACC2

14 HC

14 HCC

15 I-Core®

15 ICC2

16 PCC

16 Pro-C®

17 Pro-HC

17 X-Core®

18 Common Interrupt (Most AC-Powered Controllers)

19 Using the Soil-Clik with Solar Sync®

20 Programming

20 LED Screen Overview

21 Programming Moisture Levels

22 Pausing Operation

22 Alarms

23 Troubleshooting Guide

23 Problems, Causes, and Solutions

24 Controller Compatibility

25 Notices

25 FCC Notice

26 Certicate of Conformity to European Directives

Installation

Choose a zone with full sun exposure that is

in the fastest-drying area of the landscape. If

necessary, move valve wires so that this is the

last (highest-numbered) station to water.

Choosing the Probe Location

The moisture-sensing Soil-Clik probe must be installed

within 1,000' (300 m) of the Soil-Clik module, using

18 AWG (1 mm2) direct burial (UF) wire.

Choosing the Zone

Install the probe within the last typical zone to irrigate,

so that normal irrigation will not interrupt watering

prematurely.

1,000' (300 m)

Installation

Choosing the Exact Spot

Select an area with full sun exposure that represents the

fastest-drying irrigated area.

Installation

Place in the Root Zone

In turf applications, the probe should be placed in the root

zone, approximately 6" (15 cm) deep (adjust for actual turf

conditions).

For shrubs or trees, select a deeper depth that matches

the root zone. For new plantings, choose a spot halfway

down the root ball, adjacent to native soil.

Installation

Installing the Probe

1. Soak the lower two-thirds of the probe for 30 minutes

before installing. Do not allow water to cover the top

cap where the wires are connected.

2. Use ½" (12 mm) PVC pipe to make a vertical hole

to desired depth in the soil (outside diameter

⁄" (22 mm)).

Installation

Do not install the probe horizontally!

Installing the Probe (continued)

3. Mix a slurry of native soil and water, and pour it into

the hole.

4. Place the sensor in a vertical position (do not tilt it

more than 45°) at the bottom of the hole.

Installation

Installing the Probe (continued)

5. Pack native soil tightly around the probe. Soil must be

in full contact with the probe.

6. Allow the probe to acclimate for two to three days

and water normally, before proceeding to sensor-

based irrigation.

Installation

Mount within 6' (2 m) of the host controller.

Choosing the Module Location

The Soil-Clik module is designed for outdoor installation

when necessary. However, electronics will benet from a

protected location when practical.

An indoor location, or inside the controller enclosure (ACC,

ACC2, I-Core) is recommended. If the module must be

outdoors, place it away from direct sunlight and sprinkler

spray for best results. Avoid placing the module near

electrical boxes and sources of electrical interference.

6' (2 m)

Inhaltsverzeichnis

Andere Hunter Zubehör Handbücher

Hunter

Hunter Wireless Rain-Clik Bedienungsanleitung

Hunter

Hunter LIT-293 Bedienungsanleitung

Hunter

Hunter Wireless Rain-Clik Bedienungsanleitung

Hunter

Hunter Solar Sync Bedienungsanleitung

Hunter

Hunter Wireless Rain-Clik Bedienungsanleitung

Hunter

Hunter FLOW-CLIK Betriebsanleitung

Hunter

Hunter MINI-CLIK Stücklistenhandbuch

Hunter

Hunter FLOW-SYNC HFS Programmierhandbuch

Hunter

Hunter DSP700 Series Bedienungsanleitung

Hunter

Hunter Solar Sync Bedienungsanleitung

Hunter

Hunter 43758 Bedienungsanleitung

Hunter

Hunter BP-01 Bedienungsanleitung

Hunter

Hunter RAIN CLIK WR-CLIK Betriebsanleitung

Hunter

Hunter Rain-Clik WRC-TR Bedienungsanleitung

Hunter

Hunter Light Kit Gebrauchsanweisung

Hunter

Hunter WIRED RAIN-CLIK RAIN-CLIK Stücklistenhandbuch

Hunter

Hunter Wireless Rain-Clik Originalbetriebsanleitung

Hunter

Hunter Wireless Rain-Clik Bedienungsanleitung

Hunter

Hunter WIRED RAIN-CLIK Bedienungsanleitung

Hunter

Hunter WRC Bedienungsanleitung

Hunter

Hunter Wireless Rain-Clik Bedienungsanleitung

Hunter

Hunter RAIN-CLIK WR-CLIK Betriebsanleitung

Hunter

Hunter WFS Programmierhandbuch

Hunter

Hunter ET SYSTEM SMARTPORT Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung