IBM Eserver p Series Bedienungsanleitung

RS/6000 Enterprise Server Model H80

Eserver pSeries 660 Models 6H0 and 6H1

Installation Guide

SA38-0575-03

IBM

Fourth Edition (June 2001)

Before using this information and the product it supports, read the information in “Safety Notices” on page vii,

Appendix B, “Environmental Notices” on page 43, and Appendix C, “Notices” on page 45.

A reader’s comment form is provided at the back of this publication. If the form has been removed, address comments

to Information Development, Department H6DS-905-6C006, 11400 Burnet Road, Austin, Texas 78758-3493. To send

comments electronically, use this commercial internet address: [email protected]. Any information that you

supply may be used without incurring any obligation to you.

Note to U.S. Government Users -- Documentation related to restricted rights -- Use, duplication or disclosure is subject

to restrictions set forth in GSA ADP Schedule Contract with IBM Corp.

Contents

Safety Notices........................vii

Rack Safety Instructions .....................vii

Electrical Safety .......................viii

Laser Safety Information .....................ix

Laser Compliance ......................ix

Data Integrity and Verification ..................xi

About This Book ......................xiii

ISO 9000 .........................xiii

Online Publications ......................xiii

Related Publications ......................xiii

Ergonomic Information .....................xiv

Trademarks.........................xiv

Chapter 1. Setting Up the System .................1

Step 1. Checking Inventory ....................1

Step 2. Observe this Safety Notice During Installation ...........2

Step 3. Checking the Customer Environment ..............3

Step 4. Checking Customer Outlets .................3

Step 5. Setting Up Rails in the Rack .................5

Step 6. Installing Drawers in the Rack ................9

Step 7. Connecting JTAG and VS/COMM Cables ............11

CEC Drawer Attached to one I/O Drawer ..............11

Step 8. Connecting RIO and SPCN Cables ..............12

RIO Cabling........................12

CEC Drawer Attached to One I/O Drawer ..............13

CEC Drawer Attached to Two I/O Drawers..............14

CEC Drawer Attached to One I/O Drawer ..............15

CEC Drawer Attached to Two I/O Drawers..............16

Step 9. Setting Up Attached Devices ................17

Step 10. Updating the Device Records ................17

Step 11. Attaching External Devices .................17

Step 12. Connecting the Power ..................18

Step 13. Installing Options ....................18

Step 14. Starting the Operating System ...............18

Step 15. Running System Verification ................18

Chapter 2. Verifying the Hardware Operation .............19

Step 1. Considerations Before Running This Procedure ..........19

Step 2. Loading the Diagnostics ..................19

Step 3. Running System Verification.................20

Step 4. Performing Additional System Verification ............20

Step 5. Stopping the Diagnostics ..................21

Chapter 3. Installing Options for the System .............23

Handling Static-Sensitive Devices .................24

iii

Stopping the System Unit ....................24

I/O Drawer PCI Slot LED Definitions.................25

Installing PCI Adapters .....................26

Installing a Non-Hot-Pluggable PCI Adapter .............26

Installing a Hot-Pluggable PCI Adapter ...............28

Removing PCI Adapters.....................29

Removing a Non-Hot-Pluggable PCI Adapter .............29

Removing a Hot-Pluggable PCI Adapter ..............31

PCI Hot-Plug Manager Access ..................33

Accessing Hot-Plug Management Functions .............33

PCI Hot-Plug Manager Menu ..................34

System Firmware Updates ....................35

General Information on System Firmware Updates ...........36

Determining the Level of Firmware on the System ...........36

System Firmware Update Using a Locally Available Image ........37

Updating System Firmware From the Service Processor Menus ......37

Updating System Firmware from the AIX Service Aids ..........38

Updating System Firmware from the AIX Command Line .........38

Recovery Mode ......................38

Appendix A. Communications Statements ..............39

Federal Communications Commission (FCC) Statement ..........39

European Union (EU) Statement ..................39

International Electrotechnical Commission (IEC) Statement .........40

United Kingdom Telecommunications Safety Requirements .........40

Avis de conformité aux normes du ministère des Communications du Canada. . . 40

Canadian Department of Communications Compliance Statement .......40

VCCI Statement .......................40

Electromagnetic Interference (EMI) Statement - Taiwan ..........41

Radio Protection for Germany ...................41

Appendix B. Environmental Notices ................43

Product Recycling and Disposal ..................43

Environmental Design .....................43

Unit Emissions ........................43

Appendix C. Notices .....................45

Appendix D. System Records ..................47

Record the Serial Numbers....................47

Device Records .......................48

Memory Riser Card 1 or One-Way Processor Card...........48

Memory Riser Card 2 ....................48

Primary I/O Drawer Records ..................49

Secondary I/O Drawer Records .................51

Appendix E. General Attributes Required When Using a TTY Terminal ....53

Additional Communication Attributes.................54

Additional Keyboard Attributes...................55

Additional Printer Attributes....................56

iv Installation Guide

Index ...........................57

Contents v

vi Installation Guide

Safety Notices

danger

notice indicates the presence of a hazard that has the potential of causing

death or serious personal injury.

Danger

notices appear on the following pages:

vviii

v23

caution

notice indicates the presence of a hazard that has the potential of causing

moderate or minor personal injury.

Caution

notices appear on the following pages:

vix

v23

For a translation of the safety notices contained in this book, see

System Unit Safety

Information

, order number SA23-2652.

Rack Safety Instructions

vDo not install this unit in a rack where the internal rack ambient temperatures will

exceed 40 degrees C.

vDo not install this unit in a rack where the air flow is compromised. Any side, front or

back of the unit used for air flow through the unit must not be in direct contact with

the rack.

vCare should be taken to ensure that a hazardous condition is not created due to

uneven mechanical loading when installing this unit in a rack. If the rack has a

stabilizer it must be firmly attached before installing or removing this unit.

vConsideration should be given to the connection of the equipment to the supply

circuit so that overloading of circuits does not compromise the supply wiring or

overcurrent protection. To provide the correct power connection to the rack, refer to

the rating labels located on the equipment in the rack to determine the total power

requirement for the supply circuit.

vAn electrical outlet that is not correctly wired could place hazardous voltage on the

metal parts of the system or the devices that attach to the system. It is the

responsibility of the customer to ensure that the outlet is correctly wired and

grounded to prevent an electrical shock.

vii

Electrical Safety

Observe the following safety instructions anytime you are connecting or disconnecting

devices attached to the workstation.

DANGER

An electrical outlet that is not correctly wired could place hazardous voltage

on metal parts of the system or the devices that attach to the system. It is the

responsibility of the customer to ensure that the outlet is correctly wired and

grounded to prevent an electrical shock.

Before installing or removing signal cables, ensure that the power cables for

the system unit and all attached devices are unplugged.

When adding or removing any additional devices to or from the system,

ensure that the power cables for those devices are unplugged before the

signal cables are connected. If possible, disconnect all power cables from the

existing system before you add a device.

Use one hand, when possible, to connect or disconnect signal cables to

prevent a possible shock from touching two surfaces with different electrical

potentials.

During an electrical storm, do not connect cables for display stations, printers,

telephones, or station protectors for communications lines.

CAUTION:

This product is equipped with a three-wire power cable and plug for the user’s

safety. Use this power cable with a properly grounded electrical outlet to avoid

electrical shock.

DANGER

To prevent electrical shock hazard, disconnect all power cables from the

electrical outlet before relocating the system.

CAUTION:

This unit has more than one power supply cord. To reduce the risk of electrical

shock, disconnect two power supply cords before servicing.

viii Installation Guide

Laser Safety Information

CAUTION:

This product may contain a CD-ROM which is a class 1 laser product.

Laser Compliance

All lasers are certified in the U.S. to conform to the requirements of DHHS 21 CFR

Subchapter J for class 1 laser products. Outside the U.S., they are certified to be in

compliance with the IEC 825 (first edition 1984) as a class 1 laser product. Consult the

label on each part for laser certification numbers and approval information.

CAUTION:

All IBM laser modules are designed so that there is never any human access to

laser radiation above a class 1 level during normal operation, user maintenance,

or prescribed service conditions. Data processing environments can contain

equipment transmitting on system links with laser modules that operate at

greater than class 1 power levels. For this reason, never look into the end of an

optical fiber cable or open receptacle. Only trained service personnel should

perform the inspection or repair of optical fiber cable assemblies and receptacles.

Preface ix

xInstallation Guide

Andere Handbücher für eserver p Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere IBM Server Handbücher

IBM

IBM System x3610 Bedienungsanleitung

IBM

IBM Power 570 Installationsanleitung

IBM

IBM @server x Series Bedienungsanleitung

IBM

IBM BladeCenter HS22 Bedienungsanleitung

IBM

IBM X3850 X6 Bedienungsanleitung

IBM

IBM p5 550 Installationsanleitung

IBM

IBM xSeries 230 6RY Betriebsanleitung

IBM

IBM 9006-22P Benutzerhandbuch

IBM

IBM System x3650 M5 Montage- und Wartungsanleitung

IBM

IBM totalstorage 326 Bedienungsanleitung

IBM

IBM BladeCenter HS22 Type 7870 Bedienungsanleitung

IBM

IBM iSeries Series Administratorhandbuch

IBM

IBM B50 Bedienungsanleitung

IBM

IBM x3655 - System - 7985 Bedienungsanleitung

IBM

IBM x3100 M5 Type 5457 Montage- und Wartungsanleitung

IBM

IBM 88631SU - System x3850 - 8863 Bedienungsanleitung

IBM

IBM eServer xSeries 235 Type 8671 Bedienungsanleitung

IBM

IBM x3200 - System M3 - 7328 Bedienungsanleitung

IBM

IBM X3850 X6 Bedienungsanleitung

IBM

IBM xSeries 100 Bedienungsanleitung

IBM

IBM 8668 - Eserver xSeries 232 Betriebsanleitung

IBM

IBM System x3550 M3 Bedienungsanleitung

IBM

IBM eserver xSeries 350 Produktinformationsblatt

IBM

IBM x3850 X5 Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung

IBM eserver p Series Bedienungsanleitung

Beliebte Server Handbücher anderer Marken