IBM @Server pSeries 630 6C4 Handbuch

Quick Setup Instructions

Completing Your

System Installation

If you encounter difficulties while setting

up your system, contact your service

representative for assistance.

If you have not completed all of the steps in the Quick Setup Instructions labeled

Read Me First, locate the Read Me First Quick Setup Instructions and complete

all of the steps. Then return to this instruction set. The Read Me First Quick Setup

Instructions booklet is located in Box 1 inside the large shipping box that contains

the system drawer.

You must provide the following items:

One flat-blade screwdriver

pSeries 630-6C4

Completing Your

System Installation

Read and understand the caution notices found in this booklet. For a

complete listing of all safety notices and other documentation related to

this product, visit the IBM pSeries and AIX Information Center at

http://publib16.boulder.ibm.com/pseries/index.htm.

To access the pSeries publications, click Hardware documentation.

Check inventory

The exclamation mark surrounded by a yellow triangle

denotes caution. A CAUTION notice indicates the presence

of a hazard that has the potential of causing moderate or

minor personal injury. Before doing a step that contains a

caution icon, read and understand the caution statement that

accompanies it.

2Read safety notices

AIX 5L for

POWER V 5.2

Documentation CD

(ca_ES)

5765-E62

Licensed Materials-Property of IBM.

Recorded in the

United States of America

Note: U.S.Government users,

RESTRICTED RIGHTS-Use,

Duplication, or Disclosure

restricted by GSA ADP Schedule

Contract with IBM Corp.

See the AIX 5.2

Installation Guide

for Instructions on

the use of this CD.

COMPACTCOMPACT

DIGITALDATADIGITALDATA

LCD4-1148-00

TMTM

P/N 80P3920

LCD4-1137-03

Written in U.S.A.

Contains Licensed Material

Property of IBM.

Note: U.S.Government users,

RESTRICTED RIGHTS-Use,

Duplication, or Disclosure

restricted by GSA ADP Schedule

Contract with IBM Corp.

Version 5.2.0.30

Standalone Diagnostics

Quick Setup Instructions

Completing Your

System Installation

If you encounter difficulties while setting

up your system unit, contact your service

representative for assistance.

The pSeries Model 6C4 and Model 6E4 Installation Guide

was shipped with your system. It is located with the other

documentation in box 2. Before you begin read all safety notices and

instructions found in this manual.

If you have not completed the procedure in the Read Me First brochure,

locate the Read Me First brochure and complete all of the steps and

return to this brochure. The Read Me First brochure is located in

box 1 of your system over pack.

Items that you provide:

One flat-blade screwdriver

pSeries 630-6C4

Completing Your

System Installation

“About Your Machine” document,

books, CD-ROMs and other media

Power cables

(1 standard, 2 optional)

9-pin to 25-pin serial

converter cables (2)

(optional)

RJ-48 to 9-pin

converter cable

Keyboard (optional)

If ordered, the keyboard might

not have shipped in this box.

Note: Review your inventory

closely. If any of the components

shown on this page are missing, or

you encounter any difficulties while

setting up your system, contact your

service representative for assistance.

Mouse (optional)

If ordered, the mouse might

not have shipped in this box.

If you have internal options, such as adapters, disk drives,

or memory upgrades that are not installed, install them now.

Are all of the internal options installed?

Check your display or console

If you are using an ASCII terminal with a keyboard as the console for

this system, go to “Step 8 Connect the Serial and Parallel Cables”.

If you are using a graphics display with a keyboard and mouse,

go to “Step 6 Connect the Keyboard and Mouse”.

If you are connecting to a Hardware Management Console (HMC),

go to “Step 5 Connecting to a Hardware Management Console”.

Are you connecting to a Hardware

Management Console (HMC)?

If your HMC is already installed, complete this step. If your HMC has not been previously installed, refer to

Hardware Management Console Installation and Operations Guide or visit the

After you complete the HMC installation procedure, return here and complete this step.

IBM pSeries and AIX

Information Center at http://publib16.boulder.ibm.com/pseries/index.htm. Click hardware documentation.

To connect your HMC to your system, connect the HMC serial cable to the HMC1 connector.

If this is the second HMC being connected to your system, connect the HMC serial connector

to the HMC2 connector. After connecting the HMC, go to “Step 18 Connect the Serial and

Parallel Devices.”

Your system drawer is equipped with two HMC connectors located on the back of the system.

The connectors are labeled HMC1 and HMC2.

HMC1 HMC2

Model 6C4 HMC

Ifyou need additionalinformation aboutinstalling internal options,

visitthe IBM pSeries and AIXInformation Center at

http://publib16.boulder.ibm.com/pseries/index.htm.Click hardw are documentat ion.

Connect the graphic display

A PCI 2D graphics adapter can be installed in any of the six PCI slots.

Some displays require an additional cable.

If you have an ASCII terminal, it is preferable to connect it to serial connector S1.

However, it can also be connected to serial connector S2 or S3.

Connect the graphics display cable to the back of the display and to the graphics adapter

connector. To locate installed adapters, consult the "About Your Machine" document.

Connect the keyboard and mouse

(when using a graphic display)

Rear View

Connect the keyboard and mouse to the connectors on the rear of the system, as shown.

If a wrist/palm rest was included with your keyboard and you want to attach

it, refer to the keyboard documentation for installation instructions.

Rear View

Serial

Connector

PCI 2D

Graphics

Adapter

Connect the serial and parallel cables

Serial connector 1

(FS1 front)

Operator

panel

Rear of the

system

Rear of the

system

Rear of the

system

Serial port

number Location Examples of applicable usage

Serial connector 1

(S1 rear)

Serial connector 2

(S2)

Serial connector 3

(S3)

Service Agent, PDA system-management applications (for example, handheld

devices or mobile computers), service processor menus, ASCII terminal for AIX

console, and modems

Service Processor menus, Service Agent, PDA system management applications

(interface cable required), ASCII Terminal for AIX Console, and Modems

Service Processor menus, HACMP, ASCII Terminal for AIX Console, and Modems

HACMP, UPS (uninterruptible power supply), ASCII Terminal for AIX Console,

and Modems

Front View 1a

Rear View

1 23 4

1Serial Connector 1

1a Serial Connector 1 (RJ-48 connector)

2 Serial Connector 2

3Serial Connector 3

4 Parallel Connector

Illustration Key

Note: Do not use serial connector S1 to run HACMP or to attach a UPS. If you are configuring your system

to run HACMP with a UPS attached, you must connect the HACMP cable to serial port S2 and the UPS

cable to serial port S3. Do not run a UPS connected to serial port S2. If you decide to disconnect HACMP,

you must reset the service processor using the service processor pinhole reset switch before running

another application. The service processor pinhole reset switch is located on the operator panel. Step 16

shows the location of the service processor reset switch.

Cabling to the serial ports:

This system is equipped with two serial connectors identified as serial connector 1. One is located

at the front of the system (FS1) and the other (S1) is located at the rear of the system.

Use an RJ-48 to 9-pin converter cable to access the front serial connector FS1.

When using FS1, the rear serial connector (S1) is deactivated.

Use a 9-pin serial cable when you activate the rear serial connector S1. If you are attaching to a 25-pin

device, use a 9-pin to 25-pin serial converter cable. The converter cable is a customer-purchased option.

If you have a remote ASCII terminal, connect it through an external modem to serial connector S1.

Connect a local ASCII terminal to serial connector S2 or serial connector S3.

You can connect additional serial devices to the two remaining serial ports (S2 and S3), which are

located at the rear of the system.

Cabling to the parallel port:

If you have a parallel device, such as a printer, connect it to the parallel connector.

Connect the adapter cables

Connect the first external SCSI device

If you are using any optional adapters (such as token ring or 8-port EIA-232), connect the

cables to the appropriate adapter connectors in the PCI slots of your system. To locate

installed adapters, consult the "About Your Machine" document.

Connect the SCSI cable to the SCSI connector.

Connect the other end of the SCSI cable to the SCSI device.

If this is the last device connected, connect the SCSI device terminator.

If this is not the last device connected, go to the step 11.

Note: The built-in SCSI interface is Ultra3 SCSI. When a cable is not attached

to the SCSI connector on the system, the SCSI bus is automatically terminated.

To set the SCSI device address, refer to the SCSI device documentation.

10.1

10.2

10.3

10.4

If you are not going to install any additional optional adapters, go to step 10.

If you are not going to install an external SCSI Device, go to step 11.

Rear View

1External SCSI Connector

2 SCSI Cable to SCSI Device

3SCSI Terminator

4SCSI Device

Illustration Key

Rear View

Connect any additional external

SCSI devices

11.1

11.2

11.3

11.5

11.6

11.7

11.4

Locate the last SCSI device cabled from the system.

Remove the SCSI terminator from the last cabled SCSI device.

Connect the new SCSI cable to the SCSI connector on the last SCSI device.

Connect the other end of the SCSI cable to the new SCSI device.

Repeat substeps 11.1, 11.2, and 11.3 for each additional SCSI device that you attach.

Connect the SCSI device terminator to the last SCSI device.

To set the SCSI device address, see the SCSI device documentation.

If you are not going to install any additional external SCSI devices, go to step 12.

1System Unit to First SCSI Device Cable

2 First External SCSI Device

3SCSI Cable to Last SCSI Device

4SCSI Terminator

5Last SCSI Device

Illustration Key

Rear View

Are you using the

rack-indicator light feature?

The rack-indicator light feature signals when a drawer installed in a rack has a

failure or you have issued a locate signal. If you are unsure whether you are using

the rack-indicator light feature, ask your system administrator.

If you are not connecting a rack-indicator light to your system, go to step 13.

Connect one end of the supplied cable to the rack-indicator light feature. Connect the

other end of the cable to the rear RJ-48 connector located on the back of the Model 6C4.

Are you using an Ethernet connection?

If you are unsure whether you are using an Ethernet connection, ask your

system administrator. If you are not using Ethernet or you have already connected

your Ethernet to an adapter, go to step 14.

To connect the Ethernet cable, connect the twisted-pair cable to one of two RJ-45 connectors

located on the rear of the system drawer. For RJ-45 connector locations, see the following

illustration.

Note: The twisted-pair connector is compatible with the IEEE 802.3 Ethernet

network 10/100 Base T link.

Rack Indicator Light

Rear View

12.1

Connect the power cables to the receptacles

on the rear, and then connect the cables to

different power source outlets.

If your system is equipped with one power supply,

connect the power cable to the power receptacle.

A second power receptacle is present when a

second (redundant) power supply has been added

to the system drawer.

Note: If you are using dc to power your system,

you must have a dc power distribution source.

Shown with two power

supplies installed.

Rear View

Note: This system could be equipped with two power

supplies, each requiring a separate power cable.

CAUTION: This product is equipped with a three-wire power cable and

plug for the user’s safety. Use this power cable with a properly grounded

electrical outlet to avoid electrical shock.

Connect the power cable

14.1

14.2

15.1

15.2

15.3

Attach cables to the

cable management arm

Put the system into the service position. The rails lock in the fully extended position with a click.

Loosely wrap the hook-and-loop fastener strips around the external cables.

Note: To allow the cable to move, do not tightly wrap the hook-and-loop

fastener strip around the cables.

After you attach the cables to the cable management arm, go to the front

of the rack and move the system drawer in and out. Observe the

movement of the cable and cable management arm to verify that

the cable is not binding.

Hook-and-Loop

Fastener Strips

If you are using dc to power your system,

you must to have a dc power distribution source.

This system could be equipped with two power supplies,

each requiring a separate power cable.

Notes:

Connect your power cable to

the electrical power source

Your system is now set up

Connect the power cable(s) to the power source.

16.1

16.2

Before you press the power-on button on your operator panel,

observe the following:

The power LED is slowly blinking.

An OK prompt is visible in the operator panel display.

The following illustration shows the operator panel in standby

mode with the OK displayed in the operator panel.

If your system does not stop in standby mode, check all cables

for good connection. If you cannot find a problem, call your support center

for assistance.

1Power-On Button

2 Power LED

3Attention LED

4SCSI Port Activity

5Ethernet Port Activity

6Operator Panel Display

7 (FS1) Front Serial Connector (RJ-48)

8Service Processor Reset Switch (Pinhole)

9System Reset Button

Illustration Key

If an operating system has been preinstalled in your system, see the documentation

provided with your operating system.

If you plan to install the operating system now, see the installation instructions

provided with your operating system.

If you are installing an I/O drawer, follow the instructions that were provided with the I/O

drawer. When you have completed the I/O drawer installation, return to this booklet

and go to step 18.

Power

Distribution

Bus

9 8

61 3 4 5

Andere Handbücher für @Server pSeries 630 6C4

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere IBM Server Handbücher

IBM

IBM SG24-4576-00 Kurzanleitung zur Einrichtung

IBM

IBM Power System System E950 Bedienungsanleitung

IBM

IBM LS20 - BladeCenter - 8850 Bedienungsanleitung

IBM

IBM pSeries 670 Bedienungsanleitung

IBM

IBM x3750 M4 Bedienungsanleitung

IBM

IBM N Series Kurzanleitung

IBM

IBM 8676 - Eserver xSeries 335 Bedienungsanleitung

IBM

IBM Netfinity 6000R Bedienungsanleitung

IBM

IBM @Server pSeries 630 6C4 Handbuch

IBM

IBM x3550 M4 Type 7914 Montage- und Wartungsanleitung

IBM

IBM totalstorage 326 Bedienungsanleitung

IBM

IBM System x3950 X6 Bedienungsanleitung

IBM

IBM Netfinity 5000 Bedienungs- und Sicherheitshinweise

IBM

IBM i Series Bedienungsanleitung

IBM

IBM 71455RU Bedienungsanleitung

IBM

IBM 866631Y - Netfinity 7100 - 8666 Betriebsanleitung

IBM

IBM 9008-22L Bedienungsanleitung

IBM

IBM SC34-6814-04 Bedienungsanleitung

IBM

IBM 79788BU Bedienungsanleitung

IBM

IBM HS12 - BladeCenter - 8028 Bedienungsanleitung

IBM

IBM HS21 - BladeCenter - 8853 Bedienungsanleitung

IBM

IBM System x3950 X5 Bedienungsanleitung

IBM

IBM 8486 - eServer xSeries 100 Bedienungsanleitung

IBM

IBM eserver i5 Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung