ICP DAS USA PISO-ENCODER300U Bedienungsanleitung

PISO-ENCODER300U 3-axis Encoder Input Card - QuickStart (Nov/2016)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

PISO-ENCODER300U

PCl Bus, 3-axis Encoder Input Card

Quick Start Guide

Product Website:

http://www.icpdas-usa.com/piso_encoder_300_600.html

1. Introduction

PISO-ENCODER/300/600 has a 3-axis or 6-axis encoder counter. Each

axis has a 32-bit, true counter with maximum counting rate of 1MHz. The

Index reset resets by using a C+/C- channel, which will reset every

revolution. The hardware reset resets by an external pin (HR1 ~ HR6). The

HR1 ~ HR6 also can be a digital input. 8-channel digital outputs are also

provided. 2500Vrms photo couplers isolate the digital I/O. This board

provides DOS, windows 95 and windows NT drivers.

PISO-ENCODER300U 3-axis Encoder Input Card - QuickStart (Nov/2016)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

2. Pins assignment

The pins assignment of PISO-Encoder600(U) board is shown in the following figure.

The power source of every encoder channel is designed for the DC 5V power source of

host computer’s PCB. Therefore, do not connect those pins with other DC 5V external

power source. And the maximum current of each encoder power is 100mA. Besides,

user should apply external DC 24V power source across pins of EXT_VCC and

EXT_GND in order to use digital inputs and outputs provided in PISO-Encoder600(U)0.

Hence, the digital inputs and outputs of PISO-Encoder600(U) will work correctly based

on the commands in digital output register (section 2.2.3) and digital input register

(section 2.2.4). The detailed description of pins’ function for PISO-Encoder600(U) is

listed in Table 1.

PISO-ENCODER300U 3-axis Encoder Input Card - QuickStart (Nov/2016)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

PISO-ENCODER300U 3-axis Encoder Input Card - QuickStart (Nov/2016)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

PISO-ENCODER300U 3-axis Encoder Input Card - QuickStart (Nov/2016)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

3. System Block Diagram

The PISO-Encoder600(U) has a 6-axis encoder counter. And each axis has a 32-bit

true counter with maximum counting rate of 1MHz. It also offers three different types of

the counting mode, which are QUADRANT mode, CW_CCW mode, and PULSE_DIR

mode. User should choose the correct mode based on actual type of encoder.

Otherwise, the PISO-Encoder600(U) will not work properly. Besides,

PISOEncoder600(U) also provides 3 different functions of counter resetting mode

including register reset, index reset and hardware reset. The Index reset function is

used to reset encoder counter through using a C+/C- channel signal during every

revolution. The hardware reset function is adopted to reset encoder counter by a pre-

defined external signal pin, namely HR1~HR6. Furthermore, when PISO-Encoder600(U)

is not set on the hardware reset mode, the pins of HR1~HR6 can be open as digital

inputs. In addition, PISO-Encoder600(U) also offers 8 channels of digital output. Every

digital output and input (digital I/O) is photo-coupled isolated up to 2500Vrms. The

detailed function block diagram of PISO-Encoder600(U) is demonstrated and

summarized in the following figure.

PISO-ENCODER300U 3-axis Encoder Input Card - QuickStart (Nov/2016)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

4. Hardware address selection

The hardware address of PISO-Encoder600(U) board can be set as 0~15 by DIP switch

A0~A3 on the PISO-Encoder600(U) board, as shown in Figure 2. The factory hardware

address setting is Hex 00. If the default address of this card is used by other device,

user can change the setting to various base addresses. The addressing of PCI bus is

defined in Table 1. According to the hardware address setting, programmer should call

function ENC6_REGISTRATION(cardNo, address) to confirm with the hardware setting

in the beginning of the program. The more detailed description for function of

ENC6_REGISTRATION() will be presented in chapter 3.

Inhaltsverzeichnis

Andere ICP DAS USA PCI-Karte Handbücher

ICP DAS USA

ICP DAS USA PCIe-S114 Bedienungsanleitung

ICP DAS USA

ICP DAS USA PCI-1202 Series Bedienungsanleitung

ICP DAS USA

ICP DAS USA PCI-1202L Bedienungsanleitung

ICP DAS USA

ICP DAS USA PIO-D56 Bedienungsanleitung

ICP DAS USA

ICP DAS USA PISO-DA4U Bedienungsanleitung

ICP DAS USA

ICP DAS USA PCI-1002L Bedienungsanleitung

ICP DAS USA

ICP DAS USA PIO-D48 Bedienungsanleitung

ICP DAS USA

ICP DAS USA PCI-1800HU Bedienungsanleitung

ICP DAS USA

ICP DAS USA PCIe-LM4 Bedienungsanleitung

ICP DAS USA

ICP DAS USA PEX-D24 Bedienungsanleitung

ICP DAS USA

ICP DAS USA PCI-2602U Bedienungsanleitung

ICP DAS USA

ICP DAS USA PCI-P8R8 Bedienungsanleitung

ICP DAS USA

ICP DAS USA PCI-1202 Series Bedienungsanleitung

ICP DAS USA

ICP DAS USA PISO-P16R16U Bedienungsanleitung

ICP DAS USA

ICP DAS USA PCI-1002 LU Bedienungsanleitung

ICP DAS USA

ICP DAS USA VXC-1 8U Series Bedienungsanleitung

ICP DAS USA

ICP DAS USA PCI-M512 Bedienungsanleitung

ICP DAS USA

ICP DAS USA PISO-P8R8U Bedienungsanleitung

ICP DAS USA

ICP DAS USA PIO-D64 Bedienungsanleitung

ICP DAS USA

ICP DAS USA PCIe-8620 Bedienungsanleitung

ICP DAS USA

ICP DAS USA PISO-730 Series Bedienungsanleitung

ICP DAS USA

ICP DAS USA PEX Series Bedienungsanleitung

ICP DAS USA

ICP DAS USA PISO-CAN200U-FD-T Bedienungsanleitung

ICP DAS USA

ICP DAS USA PEX-P64 Series Bedienungsanleitung

Beliebte PCI-Karte Handbücher anderer Marken

ERMA

ERMA SSI 1417 Bedienungsanleitung

SIIG

SIIG CyberSerial Dual PCI Montageanleitung

Moxa Technologies

Moxa Technologies CP-102E Bedienungsanleitung

I-Bus

I-Bus IBC2602 Bedienungsanleitung

Exsys

Exsys EX-60102 Bedienungsanleitung

Chelsio Communications

Chelsio Communications T5 Series Bedienungsanleitung

Conrad Electronic

Conrad Electronic 97 46 71 Bedienungsanleitung

Micro Innovations

Micro Innovations USB650A Bedienungsanleitung

KTI Networks

KTI Networks KF-310 Bedienungsanleitung

Asus

Asus SpaceLink WL230 Bedienungsanleitung

SIIG

SIIG SC2475 Bedienungsanleitung

TRENDnet

TRENDnet TEW-703PI Bedienungsanleitung

Belkin

Belkin F5D7000F Bedienungsanleitung

Pericom

Pericom PI7C7100 Bedienungsanleitung

ADLINK Technology

ADLINK Technology cPCI-3548 Bedienungsanleitung

Digium

Digium TE200 Series Bedienungsanleitung

Allo.com

Allo.com 2nd Gen E1/T1/J1 Bedienungsanleitung

Western Digital

Western Digital FireWire PCI Adapter Bedienungsanleitung