Icron USB Ranger 110 Bedienungsanleitung

USB Ranger 110/410

User Guide

Featuring ExtremeUSB™ Technology

USB Ranger 110/410

Thank you for purchasing the USB Ranger. Please read this guide

thoroughly before installation.

This document applies to Part Numbers: 00-00005, 00-00006, 00-00017, 00-

00018, 00-00022, 00-00023, 00-00027, 00-00028, 00-00029, and

00-00030.

FCC Radio Frequency Interference Statement Warning

The USB Ranger has been tested and found compliant with the limits for a

Class A digital device, pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference

when installed and operated in a commercial environment. The USB Ranger

generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with this user guide, may cause harmful interference

to radio communications. Operation of the USB Ranger in a residential area

is likely to cause harmful interference in which case the user will be required

to correct the interference at his own expense.

CE Statement

We, Icron Technologies Corporation, declare under our sole responsibility

that the USB Ranger, to which this declaration relates, is in conformity with

European Standard EN 55022/A1 Class A, and EN 50082-1 (IEC 801-2,

IEC 801-3, IEC 801-4)

IC Statement

This Class A digital apparatus complies with Canadian ICES-003.

Technologies Corporation, the Icron Technologies Corporation logo, and the

Icron Technologies Corporation products referred to herein are either the

trademarks or the registered trademarks of Icron Technologies Corporation.

All other trademarks are property of their respective owners. Icron

Technologies Corporation assumes no responsibility for errors that may

appear in this manual. Information contained herein is subject to change

without notice.

User Guide

Contents

Introduction................................................................................................ 1

USB Ranger Product Contents................................................................... 1

About the USB Ranger .............................................................................. 2

Before You Begin ...................................................................................... 6

Installing the LEX Unit.............................................................................. 6

Installing the REX Unit.............................................................................. 6

Connecting the LEX Unit to the REX Unit................................................ 7

Checking the Installation............................................................................ 7

Connecting a USB Device ......................................................................... 8

Troubleshooting ......................................................................................... 9

Specifications........................................................................................... 12

Limited Hardware Warranty .................................................................... 13

Hardware Remedies ................................................................................. 13

Limitation of Liability.............................................................................. 13

Obtaining Warranty Service..................................................................... 14

Contacting Technical Support.................................................................. 14

USB Ranger 110/410

Notes

User Guide

Introduction

This manual is intended to assist IT professionals install the USB Ranger

models 110 and 410. The instructions in this guide assume a general

knowledge of computer installation procedures, familiarity with cabling

requirements, and some understanding of USB devices.

NOTE:Notes give additional information that could make installation

easier.

USB Ranger Product Contents

When you open your USB Ranger for the first time you should find the

following items:

• USB Ranger User Guide

• Local EXtender (LEX)

• Remote EXtender (REX)

• AC power adapter (optional)

• USB cable (2m long)

To complete the installation, you will also require the following items that

are not included with the product:

• USB compatible computer

• USB device

• Category 5 Unshielded Twisted Pair (UTP) cable with two RJ45

connectors (if using surface cabling),

OR,

Category 5 UTP cabling with two information outlets and two

Category 5 UTP patch cords with RJ45 connectors (if using

premise cabling)

NOTE: The maximum length of the Category 5 UTP cable, including patch

cords, must not exceed 100m.

USB Ranger 110/410

About the USB Ranger

The USB Ranger incorporates Icron’s ExtremeUSB™ technology. This

technology breaks the five-meter distance barrier for the connection of USB

peripheral devices and allows users to enjoy the benefits of USB technology

beyond the desktop. With the USB Ranger, USB devices can be located up

to 100 meters from the host computer. In addition, the USB Ranger 110 and

410 can supply power to remote low-power or high-power USB devices.

The USB Ranger is composed of two individual units, the Local EXtender

(LEX) and the Remote EXtender (REX).

The LEX Unit

The LEX unit connects to the host computer using a conventional

USB cable. Depending on your needs, it also connects to a power

outlet through an AC power adapter.

Front View

1Host LED

2Host Port (USB Type B)

3Link LED

4Link Port (RJ45)

5Power LED

6Power connector

NOTE:The power adapter for the Ranger 110 can be connected to either

the LEX unit or to the REX unit, as convenient. With the Ranger

410, the location of the power adapter also depends on whether you

are connecting high-power or low-power USB devices. (See Power

Handling on page 4).

User Guide

The REX Unit

The REX unit connects to the USB device using a conventional USB

cable. Depending on your needs, it also connects to a power outlet

through an AC power adapter. The REX 110 unit allows you to

connect one USB device. The REX 410 unit allows you to connect up

to four USB devices.

Front View Rear View (REX 410)

1Link LED

2Link Port (RJ45)

3Power LED

4Power connector

5Device LED(s)

6Device Port(s) (USB Type A)

Network Cabling

The LEX and REX units are interconnected by up to 100 meters of

Category 5 Unshielded Twisted Pair (UTP) cabling. The UTP cabling

must have a straight-through conductor configuration, with no

crossovers, and must be terminated with 8-conductor RJ45 connectors

at both ends.

Category 5 cable

USB USB

REX

cable cable(s) USB

device(s)

computer

C power adapter

(shown connected to LEX)

NOTE:Category 5 UTP cabling is the standard data communications cable

installed in most commercial and some residential buildings.

USB Ranger 110/410

USB Cables

USB cables have two distinct connectors. The Type A connector is used to

connect the cable from a USB device to the Type A port on a computer or

hub. The Type B connector is used to attach the USB cable to a USB device.

USB Type A

port USB Type A

connector

USB Type B

port

USB Type B

connector

Power Handling

Some USB devices are powered directly from the USB and do not require

individual power supplies. These devices are called bus-powered devices.

The USB Ranger can provide power to these devices so they can be operated

remotely.

Bus-powered devices are further divided into low-power and high-power

categories. Low-power devices are allowed to draw up to 100 mA from the

USB. Typical examples include mice, joysticks, and keyboards without

hubs. High-power devices are allowed to draw up to 500 mA from the USB.

Typical examples include cameras and keyboards with hubs. To determine if

a device is high-power or low-power, consult the user documentation for the

device.

The USB Ranger 110 and 410 can supply power to both low-power and

high-power devices when configured as follows:

Ranger 110

• To operate any USB device, connect the power adapter to the

LEX unit or to the REX unit, as convenient.

Ranger 410

• To operate up to four low-power devices, connect the power

adapter to the LEX unit or to the REX unit, as convenient.

• To operate up to four high-power devices, connect the power

adapter to the REX unit.

NOTE: Devices with their own power source are usually considered to be

low-power devices from a USB perspective.

User Guide

Compatibility

The USB Ranger complies with USB 1.1 specifications governing the design

of full speed USB devices. However, Icron Technologies Corporation does

not guarantee that all full speed USB devices are compatible with the USB

Ranger 110/410.

USB Ranger 110/410

Before You Begin

Before you can install the USB Ranger, you need to prepare your site.

1. Determine where the host computer is to be located and set up the

computer.

2. Determine where you want to locate the USB device(s).

3. Decide whether the power adapter is to be connected to the LEX

unit or the REX unit (see the discussion of power handling on page

4).

4. If you are using surface cabling, ensure you have enough Category

5 UTP cabling to connect the two locations.

If you are using premise cabling, ensure Category 5 UTP cabling is

installed between the two locations, with Category 5 information

outlets located near both the computer and the USB device.

Installing the LEX Unit

1. Place the LEX unit near the host computer.

2. If the power adapter is to be located with the LEX unit:

a) Plug the power adapter into a suitable AC outlet.

b) Connect the power adapter to the LEX unit.

3. Plug the Type B connector on the USB cable (included) into the

Host port on the LEX.

4. Plug the Type A connector on the USB cable into the USB port on

the computer.

Installing the REX Unit

1. Place the REX unit near the USB device.

2. If the power adapter is to be located with the REX unit:

a) Plug the power adapter into a suitable AC outlet.

b) Connect the power adapter to the REX unit.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Icron Extender Handbücher

Icron

Icron Spectra 3001-15 Bedienungsanleitung

Icron

Icron USB 3-2-1 Raven 3104 Bedienungsanleitung

Icron

Icron EL5353 Bedienungsanleitung

Icron

Icron USB Ranger 2212 Bedienungsanleitung

Icron

Icron USB 2.0 RG2304SP Bedienungsanleitung

Icron

Icron USB Rover 1850 Bedienungsanleitung

Icron

Icron Starling 3251C-10 Bedienungsanleitung

Icron

Icron USB 2.0 RG2301 Bedienungsanleitung

Icron

Icron RG2304-LAN Bedienungsanleitung

Icron

Icron USB 2.0 RG2304GE-LAN Bedienungsanleitung

Icron

Icron USB 2.0 RG2304 Bedienungsanleitung

Icron

Icron USB 3-2-1 Starling 3251C Bedienungsanleitung

Icron

Icron USB Ranger 2204 Bedienungsanleitung

Icron

Icron USB 2.0 Ranger 2311 Bedienungsanleitung

Icron

Icron VU5200 Bedienungsanleitung

Icron

Icron USB 2.0 RG2304GE-LAN Bedienungsanleitung

Icron

Icron USB 2.0 Ranger 2304GE-LAN Bedienungsanleitung

Icron

Icron RG2301 Bedienungsanleitung

Icron

Icron USB 2.0 RG2301N-LAN Bedienungsanleitung

Icron

Icron USB-2000 Bedienungsanleitung

Icron

Icron USB 3.0 Spectra 3022 Bedienungsanleitung

Icron

Icron EL5200 Bedienungsanleitung

Icron

Icron USB 3.0 SP3022 Bedienungsanleitung

Icron

Icron USB 2.0 RG2304 Bedienungs- und Wartungsanleitung

Beliebte Extender Handbücher anderer Marken

SY HDBT-60T Bedienungsanleitung

Appsys ProAudio

Appsys ProAudio ADX-16 Bedienungsanleitung

Atlona

Atlona RS232 Bedienungsanleitung

IDK

IDK OPF-TH1000-A Bedienungsanleitung

Enable-IT

Enable-IT 824WP Bedienungsanleitung

Worx

Worx Landroid RadioLink WA0864 Technisches Datenblatt

TP-Link

TP-Link TL-WA730RE Bedienungsanleitung

Camplex

Camplex CMX-HDMI-SFPL Bedienungsanleitung

SC&T

SC&T HE03-4K Bedienungsanleitung

Marmitek

Marmitek MegaView70 Bedienungsanleitung

Samsung

Samsung SCS-26UC4 Bedienungsanleitung

Foxun

Foxun SX-GES24 Bedienungsanleitung

MuxLab

MuxLab 500771 Bedienungsanleitung

foxunhd

foxunhd SX-AEX01 Bedienungsanleitung

TERK Technologies

TERK Technologies LFIRX2 Bedienungsanleitung

Devolo

Devolo Audio Extender Handbuch

Edimax

Edimax EW-7438RPn V2 Bedienungsanleitung

Shinybow USA

Shinybow USA SB-6335T5 Bedienungsanleitung