IFM Electronic Efector 300 Bedienungsanleitung

Operating instructions

Volumetric flow sensor

SQ0500

704721 / 00 06 / 2010

Contents

1 Preliminary note��4

1�1 Symbols used ��4

2 Safety instructions ��4

3 Functions and features ��5

4 Function��5

4�1 Processing of the measured signals��5

4�2 Volumetric flow monitoring��5

4�3 Consumed quantity meter ��5

4�4 Consumed quantity monitoring with pulse output��6

4�5 Consumed quantity monitoring with preset counter ��6

4�6 Temperature monitoring ��6

4�7 Volumetric flow or temperature monitoring / switching function��7

4�8 Volumetric flow or temperature monitoring / analogue function��7

4�9 Customer-specific calibration (CGA) ��8

5 Installation��9

6 Electrical connection��10

7 Operating and display elements �� 11

8 Menu��12

8�1 Menu structure��12

8�2 Explanation of the menu��13

9 Parameter setting ��14

9�1 General parameter setting��14

9�2 Settings for volumetric flow monitoring��16

9�2�1 Settings for limit value monitoring with OUT1��16

9�2�2 Settings for limit value monitoring with OUT2��16

9�2�3 Setting the analogue value for volumetric flow ��16

9�3 Settings for consumed quantity monitoring ��16

9�3�1 Settings for quantity monitoring via pulse output��16

9�3�2 Settings for quantity monitoring via the preset counter ��17

9�3�3 Settings for program-controlled counter reset ��17

9�3�4 Deactivation of the counter reset��17

9�4 Settings for temperature monitoring ��17

9�4�1 Settings for limit value monitoring with OUT2��17

9�4�2 Setting the analogue value for temperature ��17

9�5 User settings (optional)��18

9�5�1 Setting of the standard unit of measurement for volumetric flow��18

9�5�2 Configuration of the standard display ��18

9�5�3 Calibration of the curve of measured values ��18

9�5�4 Calibration reset ��18

9�5�5 Setting of measured value damping ��18

9�5�6 Setting the error behaviour of the outputs ��19

9�6 Service functions ��19

9�6�1 Reading of the min/max values for volumetric flow ��19

9�6�2 Reset of all parameters to factory setting ��19

9�7 Setting of the preset counter / pulse value (ImPS) ��20

10 Operation��22

10�1 Reading of the set parameters ��22

10�2 Changing the display unit in the Run mode��22

10�3 Fault indication ��22

10�4 General operating conditions��23

11 Scale drawing ��23

12 Technical data��24

12�1 Setting ranges ��25

13 Factory setting ��26

Preliminary note1

Symbols used1.1

►Instruction

> Reaction, result

[…] Designation of pushbuttons, buttons or indications

→Cross-reference

Important note

Non-compliance can result in malfunctions or interference�

Safety instructions2

Please read this document prior to set-up of the unit� Ensure that the product is•

suitable for your application without any restrictions�

Improper or non-intended use may lead to malfunctions of the unit or to un-•

wanted effects in your application� That is why installation, electrical connec-

tion, set-up, operation and maintenance of the unit must only be carried out by

qualified personnel authorised by the machine operator�

Checkthecompatibilityoftheproductmaterials(→12Technicaldata)withthe•

media to be measured in all applications�

For the scope of validity cULus:

The device shall be supplied from an isolating transformer having a secondary

Listed fuse rated as noted in the following table�

Overcurrent protection

Control-circuit wire size Maximum protective device rating

Ampere

AWG (mm2)

26 (0�13) 1

24 (0�20) 2

22 (0�32) 3

20 (0�52) 5

18 (0�82) 7

16 (1�3) 10

Functions and features3

The unit monitors water and aqueous media�

It detects the 3 process categories volumetric flow, consumed quantity, medium

temperature�

Function4

Processing of the measured signals4.1

The unit displays the current process values�•

It generates 2 output signals according to the parameter setting�•

OUT1: 3 selection options �� Parameter setting

Switching signal for volumetric flow quantity limit value ��(→9.2.1)

or pulse sequence for quantity meter ��(→9.3.1)

or switching signal for preset counter ��(→9.3.2)

OUT2: 4 selection options

Switching signal for volumetric flow quantity limit value ��(→9.2.2)

or switching signal for temperature limit value ��(→9.4.1)

or analogue signal for volumetric flow quantity ��(→9.2.3)

or Analogue signal for temperature ��(→9.4.2)

Volumetric flow monitoring4.2

2 switching signals for volumetric flow limit values can be provided (output 1•

andoutput2).Fortheswitchingfunctions→4.7.

An analogue signal which is proportional to the volumetric flow (4��20 mA) can•

beprovidedonoutput2.Fortheanaloguefunctions→4.8.

Consumed quantity meter4.3

The unit has an internal quantity meter� It continuously totals the volumetric flow

quantity� The sum corresponds to the current consumed quantity since the last

reset�

The current meter reading can be displayed�•

In addition the value before the last reset is stored� This value can also be•

displayed�

The meter saves the totalled consumed quantity every 10 minutes� After a power

failure this value is available as the current meter reading� If a time-controlled re-

set is set, the elapsed time of the set reset interval is also stored� So the possible

data loss can be maximum 10 minutes�

The meter can be reset as follows:

Manualreset(→9.3.3).•

Time-controlledautomaticreset(→9.3.3).•

Consumed quantity monitoring with pulse output4.4

Output1providesacountingpulseifthevaluesetin[ImPS]isreached(→9.3.1).

Consumed quantity monitoring with preset counter4.5

2 types of monitoring are possible:

Time-dependent quantity monitoring�•

Settings: [ImPS] = quantity x, [ImPR] = [no], [rTo] = time t�-

If the quantity x is reached during t, output 1 switches and remains switched-

until the meter is reset�

If the quantity x is not reached during t, the meter is automatically reset and-

counting starts again; output 1 does not switch�

Quantity monitoring not time-dependent�•

Settings: [ImPS] = quantity x, [ImPR] = [no], [rTo] = [OFF]�-

If the quantity x is reached, output 1 switches and remains switched until the-

meter is reset�

Temperature monitoring4.6

A switching signal for temperature limit values can be provided on output 2� For•

theswitchingfunctions→4.7.

An analogue signal proportional to the temperature (4��20 mA) can be provided•

onoutput2.Fortheanaloguefunctions→4.8.

Volumetric flow or temperature monitoring / switching4.7

function

OUTx changes its switching state if it is above or below the set switching limits

(SPx, rPx)� The following switching functions can be selected:

Hysteresis function / normally open: [OUx] = [Hno]�•

Hysteresis function / normally closed: [OUx] = [Hnc]�•

First the set point (SPx) is set, then the reset point (rPx) with the requested

difference�

Window function / normally open: [OUx] = [Fno]�•

Window function / normally closed: [OUx] = [Fnc]�•

The width of the window can be set by means of the difference between SPx and

rPx� SPx = upper value, rPx = lower value�







































 





1 2

HY = hysteresis; FE = window; examples for volumetric flow monitoring

When set to the window function the set and reset points have a fixed hysteresis of 0�25 %

of the final value of the measuring range� This keeps the switching state of the output stable

if the volumetric flow varies slightly�

Volumetric flow or temperature monitoring / analogue function4.8

Analogue start point [ASP] determines at which measured value the output•

signal is 4 mA�

Analogue end point [AEP] determines at which measured value the output•

signal is 20 mA�

Minimum distance between [ASP] and [AEP] = 25 % of the final value of the•

measuring range�

Current output 4 �� 20 mA (example volumetric flow monitoring)

Factory setting Measuring range scaled





























MEW = final value of the measuring range

In the set measuring range the output signal is between 4 and 20 mA�

It is also indicated:

Volumetric flow above the measuring range: output signal > 20 mA�

Customer-specific calibration (CGA)4.9

The customer-specific calibration allows changing the gradient of the curve of

measured values� It influences the display and the outputs�







 







A = operating value

V0 = curve of measured values at

factory setting

V1, V2 = curve of measured values

after calibration

The change in the increase is indicated in percent� Factory setting = 100%� After a

changethecalibrationcanberesettofactorysetting(→MenuitemCAr).

Installation5

InstalltheunitinapipeusingG⅛adapters.Max.tighteningtorque5Nm.►

Installation position:vertically in a•

rising pipe�

Horizontal installation is not recom-

mended because the specified

accuracy cannot be complied with�

Direction of flow (F) and arrow “flow•

direction” must point into the same

direction�

A: flow conditioner

flow direction

The flow conditioner can be removed�

If the unit is operated without flow

conditioner:

Provide for a calming section (B) of•

at least 20 cm on the inflow side�

Internal pipe diameter preferably

3�5 mm� Disturbances (S) caused

by bends, valves, reductions, etc�

are compensated for�

�







For operation without flow conditioner, the measurement accuracy can deviate

from the accuracy specified in the technical data� Remedy:

Carryoutacustomer-specificcalibration(→MenuitemCGA).►

Electrical connection6

The unit must be connected by a qualified electrician�

The national and international regulations for the installation of electrical

equipment must be adhered to�

Voltage supply according to EN 50178, SELV, PELV�

Disconnect power�►

Connect the unit as follows:►























Pin1 Ub+

Pin3 Ub-

Pin4

(OUT1)

Switching signal: limit values for volumetric flow�

Switching signal: quantity meter reached preset value�

Pulses: 1 pulse every time the defined volumetric flow quantity is reached�

Pin2

(OUT2)

Switching signal: limit values for volumetric flow�

Switching signal: limit values for temperature�

Analogue signal for volumetric flow�

Analogue signal for temperature�

Core colours of ifm sockets:

1 = BN (brown), 2 = WH (white), 3 = BU (blue), 4 = BK (black)

Andere Handbücher für Efector 300

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere IFM Electronic Zubehör Handbücher

IFM Electronic

IFM Electronic Ecomat200 Bedienungsanleitung

IFM Electronic

IFM Electronic Efector200 OG Bedienungsanleitung

IFM Electronic

IFM Electronic LR2059 Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 300 Bedienungsanleitung

IFM Electronic

IFM Electronic PB7 Bedienungsanleitung

IFM Electronic

IFM Electronic efector100 GG507S Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 200 Installationsanleitung

IFM Electronic

IFM Electronic efector 250 Bedienungsanleitung

IFM Electronic

IFM Electronic LK31xx Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 200 OGT1 Series Bedienungsanleitung

IFM Electronic

IFM Electronic efector100 GG507S Bedienungsanleitung

IFM Electronic

IFM Electronic LR2750 Bedienungsanleitung

IFM Electronic

IFM Electronic O5E5 A Series Bedienungsanleitung

IFM Electronic

IFM Electronic efector 160 Bedienungsanleitung

IFM Electronic

IFM Electronic PY995 Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 200 Bedienungsanleitung

IFM Electronic

IFM Electronic efector 250 Bedienungsanleitung

IFM Electronic

IFM Electronic efector100 ID503A Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 100 GM505S Bedienungsanleitung

IFM Electronic

IFM Electronic efector500 PC3 Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 100 Bedienungsanleitung

IFM Electronic

IFM Electronic efector150 Bedienungsanleitung

IFM Electronic

IFM Electronic efector 300 SM0505 Bedienungsanleitung

IFM Electronic

IFM Electronic efector200 OJ Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung

Axminster

Axminster Tooling Stylus Tip Ballpoint Pen Kit Bedienungsanleitung