IFM Electronic Efector 300 Bedienungsanleitung

Amendment to the operating instructions:

Selection of the operating mode via

IO-Link interface

SAxxxx

706416 / 00 03 / 2016

1 Preliminary note

Please read the supplied operating instructions for all articles described

below prior to set-up.

These instructions are an amendment to the supplied operating instructions of the

SAxxxx flow sensors in which all setting options via the pushbuttons on the sensor

are described.

These present instructions also give alternative options for parameter setting via

the IO-Link interface.

2 Operating modes

With regard to the software the SAxxxx flow sensor behaves like 3 sensors on a

hardware platform: The following three operating modes can be selected for flow

measurement.

Operating

mode

Medium Process value display

REL Liquids, air % of the taught range

LIQU Liquids m/s, l/min, m

/h (fps, gpm, cfm)

GAS Air m/s, l/min, m

/h (fps, gpm, cfm)

The operating modes can be set via the pushbuttons on the sensor. Alternatively,

the operating mode can be transferred to the sensor by means of the memory

plug E30398 (→3) or the LINERECORDER SENSOR software (→4).

3 Operating mode selection via memory plug E30398

By means of the memory plug E30398 it is possible to duplicate the parameter set

and therefore the operating mode of a sensor to several sensors of the same type.

Detailed function description

→Operating instructions E30398 at www.ifm.com.

3.1 Procedure

1. Set the operating mode on the sensor:

►Change from the RUN mode to the initialisation menu [

INI

]

►Select [ModE] and define the operating mode: REL, GAS, LIQU.

A medium and an internal pipe diameter must be entered for the operating modes

LIQU and GAS.

When the factory setting is changed (ModE = REL), the unit displays [≡≡≡≡] to force

these entries:

►Press [●].

> [MEdI] is displayed.

►Define medium.

> [diA] is displayed.

►Define the internal pipe diameter in mm or inch.

The operating mode REL requires a flow adjustment.

A change of the operating mode leads to a restart of the unit.

The settings are saved in the respective operating mode,

i.e. after a change of the operating mode the settings are not lost.

2. Save the parameter set of the sensor on the memory plug:

Requirement:

The memory plug is used as delivered (empty / [Write protect-

ed])

►Connect the memory plug to the supply voltage.

►Connect memory plug and sensor.

> The memory plug reads the parameter set of the sensor

and saves it.

Ub P

Reading process

Process terminated.

Memory plug full / [Write

protected].

3. Transfer parameter set to other sensors:

►Connect the memory plug to the supply voltage.

►Connect the memory plug with a sensor of the same type.

> The memory plug writes its parameter set to the sensor.

Writing process

Process terminated

►Repeat the process with sensors of the same type as often as you wish.

Ub P

4 Operating mode selection via LINERECORDER

SENSOR

4.1 System requirements

4.1.1 LINERECORDER SENSOR

Required version: 4.1.0.43.

Detailed function description

→Operating instructions QA0001 at www.ifm.com.

4.1.2 IO-Link interface E30390

Required version: from firmware 2.1.5 – 1.2.5

(production after 17/02/2016, see label on the unit).

The latest firmware is available for download at www.ifm.com.

►Download firmware and overwrite firmware on the IO-Link interface.

Detailed function description

→Operating instructions E30390 at www.ifm.com.

4.1.3 IODD (IO Device Description) for SAxxxx flow sensors

There is a separate IODD for each operating mode which is available for down-

load via ifm's homepage:

For ifm units a number of IODDs is stored in the LINERECORDER SENSOR

software. If the required IODD is missing, it can be downloaded via the symbol

marked in the LINERECORDER SENSOR:

(If the symbol is pink, new IODD files are available for download.)

4.2 Procedure

Example: SA5000 flow sensor.

1. ►Connect sensor to PC via IO-Link interface and read parameter settings

via the LINERECORDER SENSOR.

Possible error message:

►Update firmware (→4.1.2).

The parameter for the operating mode [ModE] is displayed but cannot

be changed.

The factory setting for SAxxxx is the operating mode [ModE] = REL.

2. ►Change to the offline mode.

3. ►Select IODD for the required operating mode.

Each of the three operating modes has its own IODD:

- SAxxxx (operating mode REL for flow measurement in liquids and air)

- SAxxx_GAS (operating mode GAS for flow measurement in air)

- SAxxx_LIQU (operating mode LIQU for flow measurement in liquids)

If the required IODD is not available in the unit catalogue, it has to be

downloaded in the online mode (→4.1.3).

4. ►Change parameter settings of the sensor.

5. ►Save changed parameter set as lrp file.

6. ►Change to the online mode.

In the offline mode, reading or writing to a connected device is not

possible. The saved file with the parameter set can only be accessed

in the online mode and then be written to the device.

7. ►Load parameter set as file.

►Open the lrp file stored in step 5.

The lrp file contains the operating mode selected in step 3 with the

parameter settings adapted in step 4.

8. ►Write the parameter set to the sensor

> The sensor carries out a reset and restarts:

> The sensor is now in the GAS operating mode:

In case of a new parameter setting via the LINERECORDER SENSOR the

software detects the newly set operating mode automatically.

Andere Handbücher für Efector 300

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere IFM Electronic Zubehör Handbücher

IFM Electronic

IFM Electronic efector 300 SU8001 Bedienungsanleitung

IFM Electronic

IFM Electronic efector 200 OGT Series Bedienungsanleitung

IFM Electronic

IFM Electronic PN2 Series Bedienungsanleitung

IFM Electronic

IFM Electronic efector 200 OT Bedienungsanleitung

IFM Electronic

IFM Electronic efector 300 SU9001 Bedienungsanleitung

IFM Electronic

IFM Electronic EFECTOR 500 PI26 Bedienungsanleitung

IFM Electronic

IFM Electronic Efector500 PF2058 Bedienungsanleitung

IFM Electronic

IFM Electronic efector160 LR7000 Bedienungsanleitung

IFM Electronic

IFM Electronic efector 300 SU9004 Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 500 PP70 Series Bedienungsanleitung

IFM Electronic

IFM Electronic ecomat100 CR2101 Anwendungshandbuch

IFM Electronic

IFM Electronic LR2759 Bedienungsanleitung

IFM Electronic

IFM Electronic efector 600 OWF Bedienungsanleitung

IFM Electronic

IFM Electronic PY995 Series Bedienungsanleitung

IFM Electronic

IFM Electronic efector 300 SU7200 Bedienungsanleitung

IFM Electronic

IFM Electronic O5E5 A Series Bedienungsanleitung

IFM Electronic

IFM Electronic GM701S Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 200 Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 200 OL Series Bedienungsanleitung

IFM Electronic

IFM Electronic efector150 Bedienungsanleitung

IFM Electronic

IFM Electronic efector230 Bedienungsanleitung

IFM Electronic

IFM Electronic LR7300 Bedienungsanleitung

IFM Electronic

IFM Electronic LR8009 Bedienungsanleitung

IFM Electronic

IFM Electronic GM705S Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung

Axminster

Axminster Tooling Stylus Tip Ballpoint Pen Kit Bedienungsanleitung