IFM O5D15 Series Bedienungsanleitung

Operating instructions

Optical distance sensor

O5D15x UK

80284257 / 00 04 / 2019

Contents

1 Preliminary note��3

1�1 Symbols used ��3

2 Safety instructions ��3

3 Functions and features ��4

3�1 Applications ��4

4 Installation��5

4�1 Installation conditions ��5

5 Operating and display elements ��5

6 Electrical connection��6

7 Settings��7

7�1 The sensor is to switch when the object is detected��7

8 IO-Link ��7

8�1 General information ��7

8�2 Device-specific information��7

8�3 Parameter setting tools��7

9 Operation��8

9�1 Electronic lock��8

9�2 Fault indications��8

10 Maintenance, repair and disposal��9

1 Preliminary note

1.1 Symbols used

►Instructions

> Reaction, result

[…] Designation of keys, buttons or indications

→Cross-reference

Important note

Non-compliance may result in malfunction or interference�

2 Safety instructions

• The device described is a subcomponent for integration into a system�

- The manufacturer of the system is responsible for the safety of the system�

- The system manufacturer undertakes to perform a risk assessment and to

create a documentation in accordance with legal and normative requirements

to be provided to the operator and user of the system� This documentation

must contain all necessary information and safety instructions for the operator,

the user and, if applicable, for any service personnel authorised by the

manufacturer of the system�

• Read this document before setting up the product and keep it during the entire

service life�

• The product must be suitable for the corresponding applications and

environmental conditions without any restrictions�

• Only use the product for its intended purpose (→ Functions and features).

• If the operating instructions or the technical data are not adhered to, personal

injury and/or damage to property may occur�

• The manufacturer assumes no liability or warranty for any consequences

caused by tampering with the product or incorrect use by the operator�

• Installation, electrical connection, set-up, operation and maintenance of the unit

must be carried out by qualified personnel authorised by the machine operator�

• Protect units and cables against damage�

According to cULus

Caution - Use of controls or adjustments or procedures other than those specified

herein may result in hazardous radiation exposure�

Visible laser light; CLASS 1 LASER PRODUCT�

EN/IEC 60825-1 : 2007 and EN/IEC 60825-1 : 2014 complies with 21 CFR

1040 except for deviations pursuant to Laser Notice No� 50, dated June

2007

Position of the product label Warning sign

LASER KLASSE 1

CLASS 1 LASER PRODUCT

APPAREIL A LASER CLASSE 1

3 Functions and features

The unit is used as an optical distance sensor�

3.1 Applications

• The optical distance sensor measures distances between 0�03 and 2 m�

• It has a background suppression of up to 20 m�

• The switching outputs are complementary�

The distance between the sensor and the background must be limited

to max� 20 m by the customer� Otherwise measured values can be

ambiguous → 4.1 Installation conditions.

4 Installation

4.1 Installation conditions

►Install the unit so that the object to be detected is within a measuring range of

0�03��2 m�

Any object between the set switch point and a distance of 20 m from the sensor is

suppressed�

Reflecting surfaces in the direct beam path of the sensor – also in

the range > 20 m – are to be avoided by the customer� Otherwise the

measured values can be ambiguous�

5 Operating and display elements

1: LED green: operation

2: LED yellow: switching status

3: 3-digit alphanumeric display

4: Range +

5: Range -

6 Electrical connection

The unit must be connected by a qualified electrician�

►The national and international regulations for the installation of

electrical equipment must be adhered to�

►Ensure voltage supply to EN 50178�

►Disconnect power�

►Connect the unit as follows:

DC PNP

























4: OUT1 = normally open / IO-Link

2: OUT2 = normally closed

DC NPN

























4: OUT1 = normally open / IO-Link

2: OUT2 = normally closed

Core colours of ifm sockets:

1 = BN (brown), 2 = WH (white), 3 = BU (blue), 4 = BK (black)

7 Settings

7.1 The sensor is to switch when the object is detected

►Position the object�

►Press [+] to increase the range�

> The set distance value is shown flashing in the display�

> The yellow LED lights when the object is detected�

►Press [-] to decrease the distance value�

> The set distance value is shown flashing in the display�

> During operation, the currently detected distance value is shown in the display�

8 IO-Link

8.1 General information

This unit has an IO-Link communication interface which requires an IO-Link-

capable module (IO-Link master) for operation.

The IO-Link interface enables direct access to the sensor values and parameters

and provides the possibility to set the parameters of the unit during operation�

In addition communication is possible via a point-to-point connection with a USB

adapter cable�

You will find more detailed information about IO-Link at www�ifm�com�

8.2 Device-specific information

You will find the IODDs necessary for the configuration of the IO-Link device and

detailed information about sensor values, diagnostic information and parameters

in the overview table at www�ifm�com�

8.3 Parameter setting tools

You will find all necessary information about the required IO-Link hardware and

software at www�ifm�com�

9 Operation

►Check whether the unit operates correctly�

> The LED lights when the switching output is switched�

> The detected distance value is shown in the display�

9.1 Electronic lock

The unit can be locked electronically to prevent unauthorised setting� On delivery

the unit is not locked�

Locking

►Make sure that the unit is in the normal operating mode�

►Keep [+] + [-] pressed until [Loc] is displayed�

> The unit is locked�

Unlocking

►Keep [+] + [-] pressed until [uLo] is displayed�

> The unit is unlocked�

9.2 Fault indications

Display Possible cause Switching output

[Hno] [Hnc]

[++] Too much light,

e�g� reflective surfaces ON OFF

[--] Not enough light, no object OFF ON

[nEA] Object to be measured outside the

measuring range < 30 mm ON OFF

[FAr] Object to be measured outside the

measuring range > 2500 mm OFF ON

[ERP] Plausibility (e.g. object too fast) unchanged unchanged

[SC] Short circuit at the switching output

10 Maintenance, repair and disposal

► Keep the front pane of the sensor free from soiling.

►For cleaning do not use any solvents or cleaning agents which could damage

the plastic material�

►Do not open the module housing� There are no user-serviceable components

inside�

Technical data and further information at www�ifm�com

Inhaltsverzeichnis

Andere IFM Zubehör Handbücher

IFM

IFM LDL100 Bedienungsanleitung

IFM

IFM LK 022 Series Bedienungsanleitung

IFM

IFM O1D100 series Bedienungsanleitung

IFM

IFM SB1 Series Bedienungsanleitung

IFM

IFM Efector 300 SM8100 Bedienungsanleitung

IFM

IFM OGE Bedienungsanleitung

IFM

IFM OF Series Bedienungsanleitung

IFM

IFM OGH3 Series Bedienungsanleitung

IFM

IFM O5H5 Series Bedienungsanleitung

IFM

IFM JN2301 Anwendungshandbuch

IFM

IFM O3D300 Bedienungsanleitung

IFM

IFM Efector 500 PNI02X Bedienungsanleitung

IFM

IFM JD Anwendungshandbuch

IFM

IFM GI854S Bedienungsanleitung

IFM

IFM UIT509 Bedienungsanleitung

IFM

IFM efector 200 OGS38 Series Bedienungsanleitung

IFM

IFM O4E5 Series Bedienungsanleitung

IFM

IFM OGE7 Series Bedienungsanleitung

IFM

IFM O5E5 Series Bedienungsanleitung

IFM

IFM Efector 200 O4P5 Series Bedienungsanleitung

IFM

IFM PN422 Series Bedienungsanleitung

IFM

IFM LX0020 Bedienungsanleitung

IFM

IFM Efector 200 O5 Bedienungsanleitung

IFM

IFM PC3 Series Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung