IKA MS 3 digital Bedienungsanleitung

MS 3 basic

20000005495

MS 3 digital

MS 3 basic/digital_082017

ttttttttttttttttttttttttttttttttttttttttttttttttttttttttttttttttttttttttttttttttttttttPage

Declaration of conformity 2

Safety instructions 10

Unpack sssssssssssssssssssssssssssssssssssssssssssssssss11

Correct use 11

Commissioning 12

Accessories 14

Maintenance 15

Technical data 16

Warrantydddddddddddddddddddddddddddddddddddddddd 16

•

Read the operating instructions in full before starting

up and follow the safety instructions.

• Keep the operating instructions in a place where they can be

accessed by everyone.

• Ensure that only trained staff work with the appliance.

• Follow the safety instructions, guidelines, occupational health

and safety and accident prevention regulations.

• The voltage stated on the nameplate must correspond to the

mains voltage.

• The device must only be operated with the original plug-in

power supply unit.

• Wear your personal protective equipment in accordance with

the hazard category of the medium to be processed. Otherwise

there is a risk of:

- splashing liquids

- projectile parts

- body parts, hair, clothing and jewellery getting caught.

• Set up the appliance in a spacious area on an even, stable,

clean, non-slip, dry and fireproof surface.

•

The feet of the appliance must be clean and undamaged.

• Position the knob (C) at the left stop before starting up.

Gradually increase the speed.

• Keep hand/arm vibration to a minimum (Directive 2002/44/EC)

when operated manually:

- Keep the sample container as vertical as possible.

Only

exert the minimum pressure necessary for the mixing

process

- Use attachments for multiple samples when there is a large

number of samples.

• If the shaking movement of the appliance increases (resonan-

ce), reduce the speed or pass through the critical phase as

quickly as possible.

• Reduce the speed if

- the medium splashes out of the vessel because the speed is

too high

- the appliance is not running smoothly

the appliance begins to move around because of dynamic forces.

• Firmly secure the accessories and vessels in place, otherwise

shaking vessels could be damaged or projected out.

• Check the appliance and accessories beforehand for damage

each time you use them. Do not use damaged components.

• Position one single shaking vessel in the centre and several

shaking vessels so that they are evenly spread out.

• Sharp edged vessels cause wear debris on the attachments.

• Beware of the risk of

- flammable materials

- glass breakage as a result of mechanical shaking power

• Only process media that will not react dangerously to the

extra energy produced through processing. This also applies

to any extra energy produced in other ways, e.g. through light

irradiation.

• Do not operate the appliance in explosive atmospheres, with

hazardous substances or under water.

• Safe operation is only guaranteed with the accessories descri-

bed in the ”Accessories” chapter.

• Always disconnect the plug before fitting accessories.

• The appliance does not start up again automatically following

a cut in the power supply.

• Protect the appliance and accessories from bumps and impacts.

• The appliance may heat up when in use.

• The appliance may only be opened by experts.

Contents

Safety instructions

•Unpack

- Please unpack the device carefully

- In the case of any damage a fact report must be set

immediately (post, rail or forwarder)

•Delivery scope

MS 3 basic

- Shaker MS 3 basic

- Power supply

- Standard attachment MS 3.1

- Universal attachment MS 3.3

- One-hand insert MS 1.21

- Operating instructions

MS 3 digital

- Shaker MS 3 digital

- Power supply

- Standard attachment MS 3.1

- Universal attachment MS 3.3

- One-hand insert MS 1.21

- Microtiter attachment MS 3.4

- Test tube insert MS 1.32

- Operating instructions

•Use

For mixing liquids

- Touch mode for single test tubes

- Continuous mode for single or several vessels

•Range of use

- Laboratories - Schools

- Pharmacies - Universities

This device is suitable for use in all areas except industrial areas.

The protection for the user is not ensured no more, if the equip-

ment with accessories is operated, which are supplied or are not

recommended not by the manufacturer or if the equipment in

not correct use is operated against the manufacturer default.

Unpack Correct use

Power

0 0 0

Switching on

Start

Stop

Change to

continuous

operation

Mode A

Operating mode

"Continuous operation"

Speed upto 1300 rpm

Mode A

Operating mode

"Touch operation"

Speed upto 3000 rpm

Setting timer /

0 0 5

1 0 0 1 0 1

Seconds mode

Change to

minutes mode

Countdown running:

Switch off the device

Power

Switching on the device:

Press and hold button "1" and

also press the "Power" button

Power

0 0 5

Minutes mode

Position the rotating knob at the

left stop before starting up

0 0 0

Start

Stop

1 0 0 1 0 1

(= Factory setting)

An audible signal will be given

when the countdown is

complete

Not available on

MS 3 BASIC

Change

timer setting

The value previously set

will be displayed

(Factory setting=000)

If these conditions are met, the

unit is ready for service when the

mains plug has been plugged in

Commissioning

Setting Display

Action

Power

Change mode

A B

B A

Power

Switch off the device and

switch on again, see 1

0 0 0

Countdown running:

Speed

adjustment

Mode B

Operation modes "Touch"

and "Continuous operation"

Speed upto 3000 rpm

Start

Stop

Switch off the device

Power

Switching on the device:

Press and hold button "Start/Stop"

and also press the "Power" button

Start

Stop

An audible signal will be given

when the countdown is

complete

Setting Display

Action

Operating modes

Modus A

(with speed limiter)

Modus B

(without speed limiter)

Touch mode

(with standard attachment

MS 3.1)

max. 3000

rpm

max. 3000 rpm

Continuous mode

(with all attachments)

max. 1300

rpm

max. 3000 rpm

Accessories

Possible uses and permitted speed ranges of attachments:

Designation

Description

Ident-

Nr.

Touch

mode

Continuous

mode

Speed

range (rpm)

Mode

MS 3.1

Standard attachment

For test tubes and small vessels upto

ø 50 mm

3426300 x

0/200-3000

0/200-1300

0/200-3000

A and B

MS 3.3

Universal attachment

For different rubber foam inserts

3426600 -x0/200-1300

0/200-3000

MS 3.4

Microtiter attachment

For one microtiter plate

3426400 -x0/200-1300 A

MS 3.5

PCR-Plate attachment

For one 96-well PCR-plate

3428000 -x0/200-1300 A

MS 3.51

PCR-Plate insert

- F

or inserting into the PCR-Plate attachment

3428700 -x0/200-1300 A

MS 1.21

One-hand insert

For inserting into the

universal

attachment

L001540 -x0/200-1300

0/200-3000

MS 1.30

Test tube insert