Intellinet 522533 Bedienungsanleitung

GiGabit

PCi exPress

Network

Card

user maNual

MODEL 522533

INT-522533-UM-0609-02

Thank you for purchasing the INTELLINET NETWORK SOLUTIONS

™

Gigabit PCI Express Network Card, Model 522533.

A high-performance network adapter designed to t into the PCIe slot of

your desktop computer, this card allows you to upgrade your computer to

support Gigabit network speeds without changing your copper network

cabling scheme to ber optic.

And with the easy-to-follow instructions in this manual, you’ll soon be able

to enjoy the benets of these additional features:

• Supports Gigabit speeds over existing network cable

• Full duplex speeds (20 Mbps, 200 Mbps, 2000 Mbps)

• PCI Express 1.0a bus interface ts 1, 4, 8 and 16X PCI-E slots

• Supports auto-negotiation

• Realtek 8168B chipset

• Wake-On-LAN (WOL) support

• RPL/PXE boot ROM support

• Lifetime Warranty

System Requirements

Prior to card installation, make sure the following are available:

• 32- or 64-bit PCIe master mode expansion slot compliant with PCIe

bus specications

• CD-ROM drive

• Corresponding cables (see NOTE below):

NOTE: 1000Base-T signaling requires four twisted pairs of Category 5/6

balanced cabling, as specied in ISO/IEC 11801:1995 and ANSI/EIA/

TIA-568-A (1995) and tested for additional performance using testing

procedures dened in TIA/EIA TSB95.

Port Type Media Maximum Distance

10Base-T Cat. 3, 4 or 5 UTP 100 meters

100Base-TX Cat. 5 or 5e UTP 100 meters

1000Base-T Cat. 5e or 6 UTP 100 meters

FCC Statement

This device compiles with Part 15 of the FCC Rules. Operation is subject

to the following two conditions:

1. This device may not cause harmful interference; and

2. This device must accept any interference received, including interference

that may cause undesired operation

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful

interference, in which case the user will be required to correct the

interference at his own expense.

CE Warning

In a domestic environment, this product may cause radio interference, in

which case the user may be required to take adequate measures.

hardware iNstallatioN

1. Turn off the computer and unplug the power cord.

2. Remove the computer’s cover (refer to its manual if necessary).

3. Insert the contact edge of the Gigabit PCI Express Network Card into the

connector of any available PCIe bus master expansion slot. Press the

card rmly into the slot, making sure the card’s contacts are fully seated.

4. Install the bracket screw that secures the card to the computer chassis.

5. Replace the computer’s cover.

6. Connect the UTP cable to the RJ-45 network connector.

software iNstallatioN

If the BIOS section of your computer’s boot program is Plug and Play–

compliant, BIOS will automatically congure any newly installed adapter

when the computer is turned on. NOTE: Due to occasional problems with

some Plug and Play BIOS programs, a newly installed adapter may be

assigned an interrupt number that is already used by another device. In

such case, the conict will cause faulty behavior in both devices, which

makes it necessary to run the CMOS Setup utility and manually assign

a non-conicting interrupt number.

WINDOWS 98SE

1. With the Gigabit PCI Express Network Card inserted into the PCIe

slot, turn the computer on.

2. An Add New Hardware Wizard screen will display “PCI Express

Ethernet Controller.” Click “Next.”

3. On the second Add New Hardware Wizard screen, select “Search for

the best driver for your device” and click “Next.”

4. Insert the enclosed driver CD.

5. Enter the driver pathname “E:\” (E representing your CD-ROM drive).

Click “Next.”

6. Select your installed adapter and click “Next.”

7. To complete the process, follow any remaining on-screen instructions.

8. Restart the computer.

WINDOWS Me

1. With the Gigabit PCI Express Network Card inserted into the PCIe slot,

turn the computer on.

2. An Add New Hardware Wizard screen will display “PCI Express

Ethernet Controller.” Insert the enclosed driver CD.

3. Select “Install the software automatically” and click “Next.”

4. When the device name displays on the Add New Hardware Wizard

screen, click “Finish.”

5. Restart the computer.

WINDOWS NT 4.0

1. With the Gigabit PCI Express Network Card inserted into the PCIe slot,

turn the computer on.

2. Click the My Computers icon; double-click the Control Panel icon.

3. In the Control Panel icon group, double-click the Network icon.

4. In the Network Settings dialog box, select the Adapter tab, then click

“Add” to display a list of network adapters.

5. Click “Have Disk” to select the network adapter.

6. Insert the enclosed driver CD. Enter the pathname “E:\Winnt4” (E

representing your CD-ROM drive), then click “OK.”

7. With the Gigabit PCI Network Card (“Gigabit Ethernet Network Adapter”)

string displayed in the Select OEM Option panel, click “OK.”

8. Select the connection type; click “OK.”

9. To complete the process, follow any remaining on-screen instructions.

10. Restart the computer.

WINDOWS 2000

1. With the Gigabit PCI Express Network Card inserted into the PCIe slot,

turn the computer on.

2. A Found New Hardware Wizard screen will display “Welcome to the

Found New Hardware Wizard.” Click “Next.”

3. A second Found New Hardware Wizard screen will display “Ethernet

Controller.” Select “Search for a suitable driver for my device” and

click “Next.”

4. The next Found New Hardware Wizard screen will display “Optional

search locations:” Select “Specify a location” and then click “Next.”

5. Insert the enclosed driver CD.

6. On the next Found New Hardware Wizard screen, enter the driver

pathname “E:\” (E representing your CD-ROM drive), then click “OK.”

7. The next Found New Hardware Wizard screen will display “The wizard

found a driver for the following device Ethernet Controller.” Click “Next.”

8. The nal Found New Hardware Wizard screen will display “Windows

has nished installing the software for this device.” Click “Finish” to

complete the installation.

WINDOWS XP

1. With the Gigabit PCI Express Network Card inserted into the PCIe slot,

turn the computer on.

2. An Add New Hardware Wizard screen will display “Ethernet Controller.”

Insert the enclosed driver CD.

3. Select “Install the software automatically” and click “Next.”

4. A Hardware Installation screen will display the device name (“Gigabit

Ethernet Network Adapter”). Click “Continue Anyway.”

5. The next Found New Hardware Wizard screen will display “The wizard

has nished installing the software for Gigabit Ethernet Network Adapter/

Fiber Gigabit Ethernet Network Adapter.” Click “Finish” to complete

the installation.

WINDOWS VISTA

1. With the Gigabit PCI Express Network Card inserted into the PCIe slot,

turn the computer on.

2. Windows will automatically nd the card and assign a default network

driver.

3. On the Start menu bar, go to Control Panel / System / Device

Manager / Network Adapters.

4. Double-click on this card and select “Update driver.”

5. Click “Browse” and select “Computer,” then “your CD-ROM drive,” then

“WVISTA32/64.” Click “OK” to start the installation.

6. When installation is complete, close the window.

LINUX KERNEL 2.2.x

1. Compiling rtl8169.c

“gcc -DMODULE -Wall -Wstrict-prototypes -O6 -c rtl8169.c”

2. Move the object code rtl8169.o to the directory

“/lib/modules/2.2.14-5.0/net”

“cp rtl8169.o /lib/modules/2.2.14-5.0/net”

3. Insert module to kernel

“insmod rtl8169”

4. Check the driver status

“dmesg”

5. The media can be forced to one of ve modes (see below).

The link speed and duplex mode can be forced in ve modes.

Command: “insmod rtl8169 media = SET_MEDIA”

Example: “insmod rtl8169 media=0x04” will force the link mode to be

100 Mpbs half duplex.

SET_MEDIA can be:

_10_Half = 0x01

_10_Full = 0x02

_100_Half = 0x04

_100_Full = 0x08

_1000_Full = 0x10

LINUX KERNEL 2.4.x

1. Compiling r8169.c using Makele

“make”

NOTE: Remember to assign “NEW_INCLUDE_PATH” in Makele

according to Linux kernel.

2. Move r8169.o to the directory

“/lib/modules/<kernel>/kernel/drivers/net”

“cp r8169.o /lib/modules/<kernel>/kernel/drivers/net” where <kernel>

represents the kernel version, say 2.4.18-3 in Red Hat 7.3

3. Insert module by

“insmod r8169”

4. Check driver status

“dmesg”

5. The media can be forced to one of the ve modes (see below).

Cmd: “insmod r8169 media = SET_MEDIA”

Example: “insmod rtl8169 media=0x04” will force PHY to operate in

100 Mpbs half duplex.

SET_MEDIA can be:

_10_Half = 0x01

_10_Full = 0x02

_100_Half = 0x04

_100_Full = 0x08

_1000_Full = 0x10

NOVELL NETWARE SYSTEM (4.X)

1. Update Netware Server to 4.2. NOTE: If you don’t update to 4.2, use

the update le “MSM.NLM, ETHERTSM.NLM” on the CD.

2. Run NetWare Server System.

3. When the server prompt appears, load the NetWare Server Installation

Utility (“LOAD INSTALL”).

4. In the Installation Options menu, select “Driver options.”

5. In the Driver Options menu, select “Congure network drivers.”

6. In the Additional Driver Actions menu, select “Select a driver.”

7. Press <Ins> to install an unlisted driver, then press <F3> to specify a

different path.

8. Insert the driver CD and specify the path “E:\NWServer\” (E representing

your CD-ROM drive).

9. In the Select a driver to install: menu, select “Gigabit Ethernet Network

Adapter” (Gigabit PCI Express Network Card).

10. If necessary, select the “Select/Modify driver parameters and protocols”

menu.

11. Follow any remaining instructions to complete the driver installation.

NOVELL NETWARE SYSTEM (5.X/6.X)

1. Run NetWare Server System.

2. When the server prompt appears, load the NetWare Server Installation

Utility (“LOAD NWCONFIG”).

3. In the Installation Options menu, select “Driver options.”

4. In the Driver Options menu, select “Congure network drivers.”

5. In the Additional Driver Actions menu, select “Select a driver.”

6. Press <Ins> to install an unlisted driver, then press <F3> to specify a

different path.

7. Insert the driver CD and specify the path “E:\NWServer\” (E representing

your CD-ROM drive).

8. In the Select a driver to install: menu, select “Gigabit Ethernet Network

Adapter” (Gigabit PCI Express Network Card).

9. If necessary, select the “Select/Modify driver parameters and protocols”

menu.

10. Follow any remaining instructions to complete the driver installation.

Andere Handbücher für 522533

Inhaltsverzeichnis

Andere Intellinet PCI-Karte Handbücher

Intellinet

Intellinet 524810 Bedienungsanleitung

Intellinet

Intellinet 525176 Bedienungsanleitung

Intellinet

Intellinet 522328 Bedienungsanleitung

Intellinet

Intellinet 509510 Bedienungsanleitung

Intellinet

Intellinet 523981 Bedienungsanleitung

Intellinet

Intellinet 524575 Bedienungsanleitung

Intellinet

Intellinet 522748 Bedienungsanleitung

Intellinet

Intellinet 500517 Bedienungsanleitung

Intellinet

Intellinet 509510 Bedienungsanleitung

Intellinet

Intellinet 509510 Bedienungsanleitung

Intellinet

Intellinet 523981 Bedienungsanleitung

Beliebte PCI-Karte Handbücher anderer Marken

ERMA

ERMA SSI 1417 Bedienungsanleitung

SIIG

SIIG CyberSerial Dual PCI Montageanleitung

I-Bus

I-Bus IBC2602 Bedienungsanleitung

Exsys

Exsys EX-60102 Bedienungsanleitung

Chelsio Communications

Chelsio Communications T5 Series Bedienungsanleitung

Conrad Electronic

Conrad Electronic 97 46 71 Bedienungsanleitung

Micro Innovations

Micro Innovations USB650A Bedienungsanleitung

KTI Networks

KTI Networks KF-310 Bedienungsanleitung

Asus

Asus SpaceLink WL230 Bedienungsanleitung

SIIG

SIIG SC2475 Bedienungsanleitung

TRENDnet

TRENDnet TEW-703PI Bedienungsanleitung

Belkin

Belkin F5D7000F Bedienungsanleitung

Pericom

Pericom PI7C7100 Bedienungsanleitung

ADLINK Technology

ADLINK Technology cPCI-3548 Bedienungsanleitung

Digium

Digium TE200 Series Bedienungsanleitung

Allo.com

Allo.com 2nd Gen E1/T1/J1 Bedienungsanleitung

Western Digital

Western Digital FireWire PCI Adapter Bedienungsanleitung

Pyle

Pyle Gamelink PLINK1 Bedienungsanleitung