Intex FastFill I637USB Bedienungsanleitung

(37PO) I637USB USB PUMP ENGLISH 4.875” X 7.25” 05/17/2022

READ AND SAVE THESE INSTRUCTIONS

Page 1

IMPORTANT SAFETY INSTRUCTIONS

READ AND FOLLOW ALL INSTRUCTIONS BEFORE USING THIS PRODUCT

INTEX® OWNER’S MANUAL

FastFill™ USB Pump

Model I637USB 5V 2A

037-*PO-R0-2305

English

Babies Can Suffocate

To prevent suffocation and death,

never place a baby 15 months old or

younger on this product.

WARNING

Keep product fully inflated when in use.

Child Entrapment Hazard

Always position product 1ft (30cm) or

more away from objects such as walls

and dressers to prevent a child from

being entrapped.

To reduce the risk of burns, fire, electric shock, or injury to persons:

• Never introduce any flammable substance into the inflatable air bed, SUCH AS AEROSOL TIRE REPAIR

PRODUCTS, as it may ignite or explode.

• Close supervision is necessary when this furnishing is used by, or near children, invalids, or disable persons.

• Use this furnishing only for its intended use as described in these instructions. Do not use attachments not

recommended by the manufacturer.

• Do not operate where aerosol (spray) products are being used or where oxygen is being administered.

• This is not a toy. Children must not be left unattended when using the air bed.

• If a storage bag is included, keep the storage bag away from babies and children. The storage bag is not a toy.

When not in use, fold the bag and put it away out of the reach of children.

• Do not walk, stand on or jump on or use the air bed as a trampoline.

• Do not use on or near water. This is not a raft.

• Do not set up bed near stairs, doors, sharp edges or breakable objects. Provide adequate space between bed

and objects to avoid entrapment.

•

Make sure the area is flat, smooth, free of sharp objects that could puncture the bed and keep away from ledges.

• Keep pets away from the air bed. Pets may puncture the surface of the bed.

• Avoid sleeping on the edge of the air bed. Edges produce less support than the middle of the bed.

• Never operate the furnishing with the air openings blocked. Keep the air openings free of lint, hair, and the like.

Never drop or insert object into any opening.

FOLLOW THESE RULES AND ALL INSTRUCTIONS TO AVOID SUFFOCATION,

PROPERTY DAMAGE, ELECTRIC SHOCK, BURNS OR OTHER INJURY.

• To reduce the risk of electric shock or injury, do not expose to rain. Store indoors.

CAUTION

(37PO) I637USB USB PUMP ENGLISH 4.875” X 7.25” 05/17/2022

READ AND SAVE THESE INSTRUCTIONS

Page 2

NOTE: Drawings for illustration purpose only. May not reflect actual product. Not to scale.

Due to a policy of continuous product improvement, Intex reserves the right to change

specifications and appearance, which may result in updates to the instruction manual,

without notice.

PARTS REFERENCE

INSTRUCTIONS

The pump uses the power supplied by a standard USB socket. Older USB adapters do not

supply enough power for the pump to fully inflate the air bed. Newer “fast charge” adapters

need to be used. Check that your adapter’s output is 2A or more for optimum operation.

Most USB charge ports in vehicles are too weak: a 12 volt USB adapter (12V Car Charger)

may be needed. If the pump won’t inflate the bed fully within 7 minutes, you probably need

higher output.

General

• The air pump requires an external power adapter (not included) to operate.

• Air pump input voltage / current rating: 5V / 2A or more.

• Make sure the output of the external power adapter, such as USB Wall Charger, Portable

USB Charger, 12V Car Charger or USB Port is rated 5V / 2A or more.

• No specific air pump maintenance is required. Air pump has no user serviceable parts.

• Make sure the area is flat, level, clean and free from sharp objects. To prevent puncture

or damage to the air bed, never drag the air bed across the ground. Lift the inflated air

bed when moving or changing location.

• During outdoor use, place a protective layer such as a tarp (not included) between the

selected surface and the air bed in order to prevent damage to the air bed.

• For cleaning use only clean cloth with mild soapy solution. Do not use any chemicals.

• In case of repairs, use only common PVC repair glue and patches. For flocked surfaces:

rub away the flocking material with an eraser first before applying the glue and/or patch.

Part Descriptions:

1. Control dial

2. Inflation mark ( )

3. Off mark ( )

4. Deflation mark ( )

5. Manual inflation port and cap

6. Cord compartment cover

7. USB cable

8. Air bed

(37PO) I637USB USB PUMP ENGLISH 4.875” X 7.25” 05/17/2022

READ AND SAVE THESE INSTRUCTIONS

Page 3

2. Connect the USB cable to one of the following external power adapters (not included):

• USB Wall Charger rated 5V / 2A or more. See Fig (2).

• Portable USB Charger rated 5V / 2A or more. See Fig (3).

• 12V Car Charger rated 5V / 2A or more. See Fig (4).

• USB Port rated 5V / 2A or more. See Fig (5).

3. Turn the control dial to the inflation mark ( ). See Fig (6).

4. When the air bed is fully inflated, turn the control dial back to the off mark ( ) position

closing the inflation valve. See Fig (7).

5. Lie down on the air bed to test the firmness.

6. If the air bed feels too firm, release some air by simply turning the control dial to the

deflation mark ( ) until desired firmness is achieved, then turn the control dial back to

the off mark ( ) position. If the bed feels too soft, repeat steps #3 to #6 as necessary.

FIG (2)

USB Wall Charger

FIG (3)

Portable USB Charger

FIG (4)

12V Car Charger 5V/2A USB Port

FIG (5)

FIG (7)

FIG (6)

Inflation

mark

INFLATION

1. Open line cord compartment cover and pull out the USB cable. See Fig (1).

FIG (1)

(37PO) I637USB USB PUMP ENGLISH 4.875” X 7.25” 05/17/2022

READ AND SAVE THESE INSTRUCTIONS

Page 4

INFLATION OPTION

If electrical power is not available, a conventional foot, manual, or battery-operated air

pump can be used by connecting it to the manual inflation port located inside the line cord

compartment. Do not use high-pressure air compressors. See Fig (8). Follow these steps:

1. Open line cord compartment cover and locate the

manual inflation port.

2. Make sure the control dial of the internal electric

pump is still in the off mark ( ) position.

3. Remove the cap from the manual inflation port and

insert the nozzle of the pump into the port. Inflate the

air bed to desired firmness.

NOTE: Do not overinflate. The firmness should be

approximately the same as the level achieved with the

internal electric pump.

4. Remove nozzle from manual inflation port and close the cap and the line cord cover.

FIG (8)

Proper inflation of the air bed.

The ambient temperatures of air have an effect on the air bed internal pressure. At low

ambient temperature the air will contract within the air bed and the air bed will feel softer:

add air as necessary. At high ambient temperature the air within the air bed will expand

significantly and the air bed will become hard and may burst: release air to avoid damage

to the air bed or to soften the feel. Do not expose the air bed to extreme temperatures (hot

or cold). Stretching is a natural characteristic of new vinyl. During initial use, the air bed

may become soft and require additional inflation to maintain desired firmness. This is

normal for the first few days of use. Dimensions shown are approximate and will vary due

to the vinyl temperature and the air temperature.

In no event shall Intex, their authorized agents or employees be liable for damages

(such as pin holes) to the air bed caused by negligence, ordinary wear and tear,

abuse and carelessness, or external forces.

IMPORTANT NOTE

(37PO) I637USB USB PUMP ENGLISH 4.875” X 7.25” 05/17/2022

READ AND SAVE THESE INSTRUCTIONS

Page 5

TROUBLESHOOTING GUIDE

PROBLEM CAUSE SOLUTION

Air pump does

not work

• The external power adapter/

supply output is not correct.

• Pump running continuously for

30 minutes, motor protection

system activated.

• Pump continuously connected

to a portable USB charger and

idled, hence the portable USB

charger is in rest mode.

• Make sure the output of the external power

adapter, such as USB Wall Charger, Portable

USB Charger, 12V Car Charger or USB Port

is rated 5V / 2A or more. See “INFLATION”

section.

• Switch off and disconnect the line cord from

the power adapter/ supply. Let the pump rest

for 1 minute before restarting.

• Disconnect and reconnect the USB cable to

the portable USB charger.

Air bed not fully

inﬂ ated after

5 - 7 minutes

of inﬂ ation

• The external power adapter/

supply output amperage (A) is

less than 2A.

• The manual inflation port cap is

not securely closed.

• Make sure the output of the external power

adapter, such as USB Wall Charger, Portable

USB Charger, 12V Car Charger or USB Port

is rated 5V / 2A or more. See “INFLATION”

section.

• Push the cap firmly into the manual inflation

port.

Air leaking from

the pump panel

or compartment

cover

• The control dial is not in the off

mark ( ) position.

• The manual inflation port cap is

not securely closed.

• Turn the control dial to the off mark

( )

position after inflation is completed.

• Push the cap firmly into the manual inflation

port.

DEFLATION

1. Connect the USB cable to an appropriate external power adapter. See Fig (2-5).

2. Turn the control dial to the deflation mark ( ). See Fig (9).

3. With the air bed fully deflated begin rolling the air bed from the end opposite of the pump

towards the end where the pump is located. See Fig (10).

4. When all the air is removed from the air bed, turn the control dial back to the off mark

(

) closing the valve.

5. Disconnect the USB cable from the external power adapter, place it inside the cord

compartment and close the cover. Make sure the USB cable is free of twists, kinks or

knots.

FIG (10)

FIG (9)

Deflation

mark

(37PO) I637USB USB PUMP ENGLISH 4.875” X 7.25” 05/17/2022

READ AND SAVE THESE INSTRUCTIONS

Page 6

WARNING: Changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

• Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) This device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause undesired operation.

CAN ICES-3 (B)/NMB-3 (B)

®™ Trademarks used in some countries of the world under license from/®™ Marques utilisées dans certains pays sous licence de/

Marcas registradas utilizadas en algunos países del mundo bajo licencia de/Warenzeichen verwendet in einigen Ländern der Welt in

Lizenz von/Intex Marketing Ltd. to/à/a/an Intex Development Co. Ltd., Hong Kong & Intex Recreation Corp., P.O. Box 1440, Long

Beach, CA 90801 • Distributed in the European Union by/Distribué dans l’Union Européenne par/Distribuido en la unión Europea por/

Vertrieb in der Europäischen Union durch/Intex Trading B.V., Ettenseweg 46, 4706 PB Roosendaal – The Netherlands • Distributed

in the UK by Unitex Service (UK) Limited, 21 Holborn Viaduct, London EC1A 2DY, UK.

www.intexcorp.com

STORAGE INSTRUCTIONS

1. Deflate the air bed following the “DEFLATION” instructions.

2. Make sure the air bed is clean and dry.

3. Lay the air bed flat with the sleeping surface facing upwards and follow the folding steps

on Figs (11 - 15). Fold the air bed loosely and avoid sharp bends, corners and creases

which can damage the air bed.

FIG (11) FIG (12) FIG (13) FIG (15)

FIG (14)

4. Place the air bed inside the storage bag (if included) or the original packaging and store

in a dry place.

Andere Handbücher für FastFill I637USB

Inhaltsverzeichnis

Andere Intex Wasserpumpe Handbücher

Intex

Intex FastFill I637USB Bedienungsanleitung

Intex

Intex Krystal Clear CS15110 Bedienungsanleitung

Intex

Intex Quick-Fill AP633 Bedienungsanleitung

Intex

Intex FastFill AP619DA Bedienungsanleitung

Intex

Intex QUICK FILL PLUS Bedienungsanleitung

Intex

Intex SF15220 Bedienungsanleitung

Intex

Intex ECO15230-2 Bedienungsanleitung

Intex

Intex AP619A Bedienungsanleitung

Intex

Intex Krystal Clear SF90220T Bedienungsanleitung

Intex

Intex AP638 Bedienungsanleitung

Intex

Intex Fast-Fill 619PC Bedienungsanleitung

Intex

Intex Quick-Fill AP609 Bedienungsanleitung

Intex

Intex Krystal Clear C1500 Bedienungsanleitung

Intex

Intex Krytstal Clear 634T Bedienungsanleitung

Intex

Intex Built-in Fast-Fill AP620A Bedienungsanleitung

Intex

Intex Krystal Clear C330 Bedienungsanleitung

Intex

Intex Krystal Clear C2500 Bedienungsanleitung

Intex

Intex Krystal Clear SF10220 Bedienungsanleitung

Intex

Intex Krystal Clear 601 Bedienungsanleitung

Intex

Intex Fast-Fill AP640R Bedienungsanleitung

Intex

Intex AP619A Bedienungsanleitung

Intex

Intex Fast-Fill AP640R Bedienungsanleitung

Intex

Intex Krystal Clear 604 Bedienungsanleitung

Intex

Intex Krystal Clear 601 Bedienungsanleitung

Beliebte Wasserpumpe Handbücher anderer Marken

Neptun

Neptun NPHW 5500 Bedienungsanleitung

Sensidyne

Sensidyne Gilian BDX-II Montage- und Bedienungsanleitung

Draper

Draper 47808 Bedienungsanleitung

Trolla

Trolla 12820 Bedienungsanleitung

Sunfab

Sunfab SVH Series Bedienungsanleitung

WilTec

WilTec 50740 Bedienungsanleitung

Fieldmann

Fieldmann FVC 5015 EK Bedienungsanleitung

Everbilt

Everbilt EFSUB5-122HD Bedienungsanleitung

Graco

Graco Husky 3300e Bedienungsanleitung

esotec

esotec 101018 Bedienungsanleitung

Becker

Becker BASIC VASF 2.80/1-0.AC230 Bedienungsanleitung

Sykes AmeriPumps

Sykes AmeriPumps GP100M Fehlerbehebungshandbuch

DUROMAX

DUROMAX XP WX Series Bedienungsanleitung

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Bedienungsanleitung

Franklin Electric

Franklin Electric IPS Bedienungsanleitung

Xylem

Xylem e-1532 Series Bedienungsanleitung

Milton Roy

Milton Roy PRIMEROYAL Bedienungsanleitung

STA-RITE

STA-RITE ST33APP Bedienungsanleitung