Ipf electronic OT330571 Bedienungsanleitung

OT330571

operating range 30 … 200mm

plastic housing, compact design

setting by Teach-In

LED-display with setting control

small beam-spot because of PinPoint-LED

suppression of reciprocal influence

M8-connector,

4-pin

technical data

function background suppression

sensing range 30 … 200mm

adjustment range 30 … 200mm

operating voltage 10 … 30V DC

current consumption (without load) ≤ 45mA

output current (max. load) ≤ 100mA

output signal push-pull, no/nc

voltage drop ≤ 3V DC

response time / decay time ≤ 0.5ms

sampling frequency 1kHz

transmitting element (pulsed) LED, red-ligth, punctual

wavelength 630nm

short-circuit protection +

reverse polarity protection +

operating mode display LED green

display (signal) / setting control LED yellow

display (Teach-In) LED blue

interference suppression +

housing material plastic (ASA, MABS)

front screen material PMMA

degree of protection (EN60529) IP67

operating temperature

connection

-25 … +60°C

M8-connector, 4-pin

electric connection dimensional drawing light beam form

colors of LED

color independent diffuse reflection

sensor with background

suppression

●all dimensions in mm *transmitter axis

MANUAL •Subject to alteration! Version: June 2014

ipf electronic gmbh

•Rosmarter Allee 14 •58762 Altena

│

Tel +49 2351 9365-0 •Fax +49 2351 9365-19

│

[email protected] •www.ipf-electronic.com 1

Teach-in procedure for 1 point-teach (normal):

1. Aim the sensor to a reference surface e.g. a reflecting machinepart and make sure that

the blue Teach-LED ligths.

2. Touch the blue Teach-LED which is placed at the rear side of the housing with a

ferromagnetic tool for longer than 2 sec. but max. 4 sec., until all 3 LEDs start blinking

with a frequency of 1 HZ.

The blue Teach-LED flashes stronger once a tool is detected.

3. Touch the blue Teach-LED again for a short time with a ferromagnetic tool

in order to confirm the reference surface.

4. The standard configuration of the output is nc (normally closed).

It can be changed to no (normally open) by touching the blue LED again for a short

time within 4 sec. During this time all 3 LEDs are blinking slowly (1Hz).

5. As soon as only the blue LED lights, the Teach-in procedure is finished successfully.

Teach-in procedure for 2 point-teach (for objects close to background):

1. Aim the sensor to a reference surface e.g. a reflecting machinepart and make

sure that the blue Teach-LED ligths.

2. Touch the blue Teach-LED which is placed at the rear side of the housing

with a ferromagnetic tool for longer than 4 sec. but max. 6 sec., until all 3

LEDs start blinking with a frequency of 2Hz.

The blue Teach-LED flashes stronger once a tool is detected.

3. Touch the blue Teach-LED again for a short time with a ferromagnetic

tool in order to confirm the reference surface.

4. Remove the object from detection range and touch the blue Teach-LED

for a short time to teach the background.

5. As soon as only the blue LED lights, the Teach-in procedure is finished successfully.

If all LEDs blink fast (8Hz), the Teach-in procedure failed and has to be repeated.

MANUAL •Subject to alteration! Version: June 2014

ipf electronic gmbh

•Rosmarter Allee 14 •58762 Altena

│

Tel +49 2351 9365-0 •Fax +49 2351 9365-19

│

[email protected] •www.ipf-electronic.com 2

Note: The yellow LED indicates the detection of an object, but does not compulsory correspond to the switching output. The

Teach-In function is active for only 5min. after switching on power. The Teach-in procedure is operating with a

ferromagnetic tool as well as with 2 pin of M8-connector (white wire) by connection to operating voltage

(+Ub).

Reset to the factory settings

Touch the blue Teach-LED which is placed at the rear side oft he housing with a

ferromagnetic tool for 6 sec. until all 3 LEDs blink with a frequency of 4Hz and remove

the tool immediately. Following the blue Teach-LED should blink normally and the

sensor removes to factory settings.

connection: e.g.

VK200375

mounting bracket:

AY000118

Warning: Never use these devices in applications where the safety of a person depends on their functionality.

MANUAL •Subject to alteration! Version: June 2014

ipf electronic gmbh

•Rosmarter Allee 14 •58762 Altena

│

Tel +49 2351 9365-0 •Fax +49 2351 9365-19

│

[email protected] •www.ipf-electronic.com 3

Andere ipf electronic Zubehör Handbücher

ipf electronic

ipf electronic UT30C310 Bedienungsanleitung

ipf electronic

ipf electronic UT360321 Bedienungsanleitung

ipf electronic

ipf electronic UT189020 Bedienungsanleitung

ipf electronic

ipf electronic OTQ80576 Bedienungsanleitung

ipf electronic

ipf electronic IV56E205-S Bedienungsanleitung

ipf electronic

ipf electronic UT189023 Bedienungsanleitung

ipf electronic

ipf electronic ON330571 Bedienungsanleitung

ipf electronic

ipf electronic MW10015 Series Bedienungsanleitung

ipf electronic

ipf electronic OTR49175 Bedienungsanleitung

ipf electronic

ipf electronic ON430570 Bedienungsanleitung

ipf electronic

ipf electronic DW34312 Series Bedienungsanleitung

ipf electronic

ipf electronic UT300027 Bedienungsanleitung

ipf electronic

ipf electronic PY740020 Bedienungsanleitung

ipf electronic

ipf electronic RO570900 Bedienungsanleitung

ipf electronic

ipf electronic UT139570 Bedienungsanleitung

ipf electronic

ipf electronic DW34311 Series Bedienungsanleitung

ipf electronic

ipf electronic OTQ90170 Bedienungsanleitung

ipf electronic

ipf electronic DW35312 Series Bedienungsanleitung

ipf electronic

ipf electronic OT450521 Bedienungsanleitung

ipf electronic

ipf electronic ON430571 Bedienungsanleitung

ipf electronic

ipf electronic OTR49170 Bedienungsanleitung

ipf electronic

ipf electronic OT05E244 Bedienungsanleitung

ipf electronic

ipf electronic UT36002B Bedienungsanleitung

ipf electronic

ipf electronic PRQ80376 Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung

ipf electronic OT330571 Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken