Joerns Oxford Bedienungsanleitung

Service Manual

Oxford®Switch

Oxford®

Switch

Contents

Inspection Criteria...................................................................................................................................... 3

Service / Repair Schedule......................................................................................................................... 4

Torque Settings.......................................................................................................................................... 8

Notes ....................................................................................................................................................... 10

Oxford®

Switch

Joerns Healthcare Ltd recommends a thorough inspection and test of the Oxford Switch and its

accessories, belts etc. is carried out every six months. The examination and test should be conducted

according to the recommendations and procedures below. Joerns Healthcare Ltd recommends,

authorised service dealers should carry out maintenance, inspection and certied testing only.

CAUTION

In the event of identifying any faulty items, please contact your local authorised service provider

or Joerns Healthcare directly.

Frame

• Check the operation of the sliding section quick release pins.

• Make sure the frame is fully engaged into the base supports.

• Ensure both frame locking knobs are fully tightened.

Castors and Wheels

• Check all castors and wheels for rm attachment to the base.

• Check for free rotation of the wheels and the castors swivel.

• Check for excessive wear, cracking or splits on the centre wheel outer tyre and the corner castor

wheels.

• Where possible, remove any build up of threads, hair or bres.

• Lubricate the swivel and axle bearings, if necessary, with a light mineral based grease or food grade

spray lubricant.

• Check correct operation of the brakes.

Cleaning

Clean with ordinary soap and water and/or any hard surface disinfectant. Harsh chemical cleaners or

abrasives should be avoided as these may damage the surface nish of the product. After cleaning, the

unit should be thoroughly dried.

WARNING

OXFORD RECOMMENDS THE USE OF GENUINE OXFORD PARTS. Oxford sling/belt and products

are designed to be compatible with one another. For country specific guidance on sling/belt use

and compatibility, please refer to the sling/belt label or contact your local market distributor or

Joerns Healthcare.

Inspection Criteria

Oxford®

Switch

Tools Required

• 5mm hex key

• 6mm hex key

• 8mm A/F combination spanner

• 2 x 10mm A/F combination spanner

• 14mm A/F combination spanner

• 16mm A/F combination spanner

• 0-50Nm range torque wrench

• 17mm A/F socket

• Socket wrench

• Medium weight hammer

• Large (7mm) at blade screwdriver

Corner Castors

NOTE: To aid removal, it is recommended the frame is removed as detailed in the ‘Frame Removal’

procedure.

Removal

1. Unscrew the castor spindle using 2-off 10mm A/F combination spanners.

2. Withdraw the spindle from the castor wheel.

3. Remove the castor wheel from the castor swivel bracket.

4. Unscrew the castor swivel bracket retaining nut using a 17mm A/F socket and socket wrench.

5. Withdraw the castor swivel bracket from the M10 retaining stud.

6. Tap out the M10 retaining stud from the base using a medium weight hammer.

Replacement

1. Insert the M10 retaining stud through the square hole in the base.

NOTE: Ensure the square shank of the retaining stud locates correctly in the square hole in the base.

2. Tap the M10 retaining stud into the base using a medium weight hammer.

3. Unscrew the castor spindle of the replacement corner castor using 2-off 10mm A/F combination

spanners.

4. Withdraw the spindle from the castor wheel.

5. Remove the castor wheel from the castor swivel bracket.

6. Correctly locate the castor swivel bracket over the M10 retaining stud.

7. Screw the M10 retaining nut onto the M10 retaining stud and tighten to 25Nm using a 17mm A/F

socket and socket wrench.

8. Correctly position the castor wheel between the castor swivel bracket and insert the castor spindle

through the swivel bracket and castor wheel.

9. Screw the M6 nut onto the castor spindle and tighten to 15Nm using 2-off 10mm A/F combination

spanners.

10. Replace the frame as detailed in the ’Frame Replacement’ procedure.

Service / Repair Schedule

Oxford®

Switch

Centre Wheels

NOTE: The frame must be removed to enable removal of the centre wheels as detailed in the ‘Frame

Removal’ procedure.

Removal

1. Unscrew the centre wheel bolt using a 6mm hex key and a 16mm A/F combination spanner.

2. Withdraw the centre wheel bolt from the wheel.

3. The wheel will now be free.

Replacement

1. Insert the sleeve through the centre hole of the wheel.

2. Insert the button head wheel bolt through the sleeve and wheel.

3. Insert the button head wheel bolt and sleeve through the holes in the centre wheel bracket (front and

rear) on the base.

4. Screw the M10 domed nut onto the wheel bolt and tighten to 25Nm using a 16mm A/F combination

spanner and a 6mm hex key.

5. Replace the frame as detailed in the ‘Frame Replacement’ procedure.

Frame

Removal

1. Unscrew both frame securing knobs by rotating counter-clockwise until they disengage from the

threaded retaining supports on the base.

2. Withdraw the securing knobs from the frame.

3. Withdraw the frame from the retaining supports on the base.

Replacement

1. Insert the frame into the retaining supports on the base.

NOTE: Ensure the slots in the bottom of the frame tubes correctly locate over the centre wheel

sleeves. Ensure correct orientation of the frame i.e. knee pads facing away from the operator.

2. Insert the frame securing knobs through the holes in the frame.

NOTE: Ensure the plastic frame clamps are correctly orientated on the frame securing knobs prior to

inserting through the frame.

3. Screw the frame securing knobs into the supports on the base and hand tighten securely.

Oxford®

Switch

Brake Pedal/Pad

Removal

1. Unscrew the right hand brake lever M8 domed securing nut using a 14mm A/F combination spanner.

2. Withdraw the brake lever, brake lever securing bolt, nylon bush and brake pad spring from the hole in

the base.

3. Remove the retaining circlip from the rear of the right hand brake pad spindle using a large (7mm) at

blade screwdriver.

Replacement

NOTE: Prior to re-assembly of the brake pedal, the red and green decals must be afxed in the

appropriate positions on the brake pedal.

1. Insert the brake pad spindle through the brake pad, ensuring correct orientation.

2. Position the nylon spacing bush onto the brake pad spindle, ensuring the smaller diameter is

immediately adjacent to the rear of the brake pad.

3. Insert the brake pad spindle through the appropriate hole in the base.

4. Fit the retaining circlip to the rear of the brake pad spindle, ensuring it locates securely in the groove.

5. Position the brake pad spring behind the brake pad and align the hole with the corresponding hole in

the base - see illustration below.

6. Insert the brake pedal securing bolt through the square hole in the brake pedal, ensuring correct

orientation.

7. Insert the nylon spacing bush onto the brake pedal securing bolt, ensuring correct orientation. i.e. the

larger diameter head should be immediately adjacent to the brake pedal.

8. Insert the brake pedal securing bolt through the hole in the brake pad spring and the hole in the base.

NOTE: Ensure the square shank of the securing bolt locates correctly in the square hole in the brake

pedal.

9. Fit the M8 brake pedal domed securing nut to the brake pedal securing bolt and tighten to 20Nm using

a 14mm A/F combination spanner.

Repeat the ‘Brake Pedal/Pad Removal/Replacement’ procedure for the left hand brake pedal.

WARNING

Ensure the brakes operate correctly before returning the Oxford Switch to service.

Oxford®

Switch

Base

Removal

1. Remove the frame as detailed in the ‘Frame Removal’ procedure.

2. Remove the 4-off corner castors as detailed in the ‘Corner Castors Removal’ procedure.

3. Remove the 2-off centre wheels as detailed in the ‘Centre Wheels Removal’ procedure.

4. Remove the 2-off brake pedals and brake pads as detailed in the ‘Brake Pedal/Pad Removal’

procedure.

Replacement

NOTE: Prior to re-assembly, it will be necessary to afx the base decals, ensuring they are correctly

located.

1. Assemble the left and right brake pedal/pads to the base as detailed in the ‘Brake Pedal/Pad

Replacement’ procedure.

2. Assemble the 2-off centre wheels to the base as detailed in the ‘Centre Wheels Replacement’

procedure.

3. Assemble the 4-off corner castors to the base as detailed in the ‘Corner Castor Replacement’

procedure.

4. Assemble the frame to the base as detailed in the ‘Frame Replacement’ procedure.

Knee Pad Sliding Section

Removal

1. Remove the frame as detailed in the ‘Frame Removal’ procedure.

2. Pull the 2-off knee pad positioning spring-loaded quick release pins outwards whilst simultaneously

pulling the knee pad sliding section off the frame.

Replacement

1. Correctly orientate the knee pad sliding section (pads facing away from the operator) and, whilst

pulling the 2-off spring-loaded quick release pins outwards, slide the knee pad section onto the frame.

2. Assemble the frame to the base as detailed in the ‘Frame Replacement’ procedure.

Knee Pads

Removal

1. Unscrew the 2-off M6 cap head knee pad retaining screws using a 5mm hex key.

2. The knee pads will now be free.

Replacement

1. Align the 2 holes in the knee pad retaining bracket with the M6 threaded holes in the knee pad.

2. Insert the 2-off M6 cap head knee pad retaining screws through the holes in the retaining bracket and

tighten to 10Nm using a 5mm hex key.

Oxford®

Switch

Knee Pad Positioning Spring-Loaded Quick Release Pins

Removal

1. Unscrew the knee pad positioning spring-loaded quick release pin from the knee pad sliding section

using an 8mm A/F combination spanner.

Replacement

1. Assemble the knee pad positioning spring-loaded quick release pin to the thread on the knee pad

sliding section.

2. Tighten to 10Nm using an 8mm A/F combination spanner.

Oxford®

Switch

Torque Settings

Tighten the frame

securing screws

hand tight - 2 places

Tighten the knee pad

retaining screws to

10Nm - 4 places

Tighten the knee pad spring-loaded quick

release pins to 10Nm - 2 places

Tighten the castor

spindle securing nut

to 20Nm - 4 places

Tighten the

corner castor

securing nut

to 25Nm

- 4 places

Tighten the centre

wheel securing nut

to 25Nm - 2 places

Tighten the brake

pedal securing nuts

to 20Nm - 2 places

Oxford®

Switch

Notes:

Andere Handbücher für Oxford

Inhaltsverzeichnis

Andere Joerns Medizinische Geräte Handbücher

Joerns

Joerns Hoyer HPL700 Leitfaden

Joerns

Joerns OXford Full Body (Hybrid) Bedienerhandbuch

Joerns

Joerns Arise LAL 1000 EX Fehlerbehebungshandbuch

Joerns

Joerns Hoyer HPL450 Bedienungsanleitung

Joerns

Joerns Oxford Bedienerhandbuch

Joerns

Joerns Oxford Limb Lifter Bedienerhandbuch

Joerns

Joerns Oxford Bedienerhandbuch

Joerns

Joerns Oxford UltraFine Deluxe Bedienerhandbuch

Joerns

Joerns CairTurn RT Fehlerbehebungshandbuch

Joerns

Joerns Oxford Up Bedienungsanleitung

Joerns

Joerns Oxford Mini Series Bedienerhandbuch

Joerns

Joerns DermaFloat LR Fehlerbehebungshandbuch

Joerns

Joerns Hoyer Bedienerhandbuch

Joerns

Joerns Hoyer Bedienerhandbuch

Joerns

Joerns Oxford Stretcher Adjustment Cradle Bedienerhandbuch

Joerns

Joerns HPL400 Bedienungsanleitung

Joerns

Joerns Dolphin Fluid Immersion Simulation System Fehlerbehebungshandbuch

Joerns

Joerns Camtec Series Fehlerbehebungshandbuch

Joerns

Joerns Arise 1000 Fehlerbehebungshandbuch

Joerns

Joerns Oxford Standing Harness Bedienerhandbuch

Joerns

Joerns Oxford Elevate Bedienerhandbuch

Joerns

Joerns Oxford Bedienerhandbuch

Joerns

Joerns Oxford Presence Bedienerhandbuch

Joerns

Joerns Oxford 0Y0050 Bedienerhandbuch

Beliebte Medizinische Geräte Handbücher anderer Marken

TekTone

TekTone Tek-CARE160 Bedienungsanleitung

NeuroMetrix

NeuroMetrix Quell 2.0 Bedienungsanleitung

AMT

AMT XLR8 Bedienungsanleitung

EDAN

EDAN SONOTRAX Pro Bedienungsanleitung

Restorative Therapies

Restorative Therapies RT300 Bedienungsanleitung

Gendex

Gendex Expert DC Bedienungsanleitung

Dexcowin

Dexcowin ADX4000W Bedienungsanleitung

Libelium

Libelium MySignals Bedienungsanleitung

Acelity

Acelity V.A.C.ULTA 4 Bedienungsanleitung

Caputron

Caputron ActivaDose II tDCS Bedienungsanleitung

Plinth 2000

Plinth 2000 93CDT Bedienungsanleitung

GE SENOGRAPHE 800T Bedienungsanleitung

GE Definium 5000 Bedienungsanleitung

Kanmed

Kanmed GE-1380 Bedienungsanleitung

Huntleigh

Huntleigh FD1 Bedienungsanleitung

Stryker

Stryker SPR Plus Bedienungsanleitung

Tobii Dynavox

Tobii Dynavox I-Series Bedienungsanleitung

S-Capepod

S-Capepod Evac Cocoon Bedienungsanleitung