Johnson Controls SABROE GHUR 0710 Bedienungsanleitung

GHUR intermediate cooler

Installation, operation and maintenance manual

Installation, operation and maintenance manual - GHUR intermediate cooler

2/6 012051 en 2021.02

GHUR intermediate cooler

Design

GHUR is an open intermediate cooler. It is used in two-stage refrigeration plants for mixing of the

discharge gas from the low-stage side and the two-phase fluid from the high-stage side.

Option: for increased separator effect, a demister can be added.

Function

The low-pressure discharge line and the two-phase line from the high-pressure side, enter the

vessel through the same end cover. The fluids in the two lines are mixed inside in a mixing pipe.

The mixed fluids then enter the shell through a distribution pipe, in which the fluid is separated

from the gas. The gas leaves the intermediate cooler through a suction slot pipe at the top of the

vessel.

The liquid accumulates at the bottom and surges into the receiver. A float expansion valve inside

the receiver leads the liquid to the low-pressure side and keeps the refrigerant charge at a

minimum.

Installation, operation and maintenance manual - GHUR intermediate cooler

012051 en 2021.02 3/6

GHUR intermediate cooler

Dimensions

GHUR-

type

Gas

inlet

Mixture

inlet

Gas

outlet

Liquid

outlet

0710 100 40 100 100 396 660 Ø703

0712 100 40 100 100 642.5 665 Ø703

0715 100 40 100 100 704.5 853 Ø703

Shipping

The vessel is primed and delivered with blinded connections.

The primer is not intended for outdoor storage. If the heat exchanger is not to be placed in imme-

diate service, take precautions to prevent rusting or contamination.

The vessel must only be lifted when empty and must not be subject to strokes or bumps during

transport. When lifting the vessel before it is built into the unit, straps around the shell must be

used. The weight appears from the technical data.

When the vessel is built together with the unit, a shipping description can be made.

Installation

The site and personal protection must be in accordance with EN 378-3 or national requirements.

Check the vessel immediately upon receipt for any damage occurred during transport. If the ves-

sel is damaged, it must not be installed and started.

When placing the vessel, make sure there is enough space for inspection, maintenance, escape

and emergency.

Foundations must be sufficiently robust, as their purpose is to provide permanent support without

settling and to absorb any normal vibrations from outside causes.

Installation, operation and maintenance manual - GHUR intermediate cooler

4/6 012051 en 2021.02

GHUR intermediate cooler

Make sure that no dirt or other unknown elements enter the vessel during installation.

Do not remove protective plugs and covers until immediately before installation.

The entire system must be clean before starting the operation. When fitting the tube connections,

make sure that the load from the piping on the connections is kept small and insignificant as the

vessel is not designed to be an anchor point in the piping system. Vibrations must be minimised,

possibly by means of vibration dampers.

Welding must not be carried out on the vessel.

The vessel must be secured against exceeding the allowable pressures and temperatures.

All outer surfaces must have a corrosion resistant surface coating to allow the vessel to be in-

stalled in certain environments without it causing corrosion.

Safety equipment

Before the vessel is put into operation, it must be provided with safety equipment. The manufac-

turer of the refrigeration plant is responsible for the safety equipment as it is not included in the

vessel delivery.

Start-up and operation

Before start-up, make sure that all connections are tight.

To avoid accidents or personal injury, the person responsible for the plant must make sure that

the operating staff is duly trained and instructed before the refrigeration plant is started. The in-

struction should be based on the unit instruction manuals and should include instructions in con-

struction, supervision, operation and maintenance of the system as well as the handling of used

refrigerant.

Evacuation and charging with refrigerant must be carried out in accordance with the description

in the unit instruction manual.

Before operation, the refrigeration plant must be leak tested and inspected by an authorised

person.

Local safety and health regulations must be observed.

The authorised person makes a certificate which must be kept by the user.

Bolted connections

Normal relaxing of the gasketed joints may occur in the interval between testing at the manufac-

turer’s and installation on site. Therefore, all external bolted joints may require retightening after

installation and, if necessary, once again when the vessel has reached its operating temperature.

Note that retightening must never be performed during operation.

It is important that all bolted joints are tightened evenly and in a diametrically staggered pattern.

All bolts must be tightened to the same torque using a torque wrench.

Installation, operation and maintenance manual - GHUR intermediate cooler

012051 en 2021.02 5/6

GHUR intermediate cooler

Maintenance

The vessel should be inspected at the inspection intervals stated in the compressor specification.

Only qualified personnel must carry out inspection.

Operating experience will determine how often inspection of the vessel is needed. It depends on

the operating conditions. Johnson Controls Denmark recommends inspection to be carried out in

monthly intervals during the running-in period. After a running-in period of six months, a mainte-

nance plan must be made. Johnson Controls Denmark recommends inspection to be carried out

every third month as a minimum.

Do not disconnect or tighten connections when the equipment is under pressure.

Periodic inspection during the service life of the vessel must meet the requirements of national

legislation or EN 378-2. Correspondingly, a visual inspection of connections, outer surfaces,

bases, the vibration damper and safety equipment must be carried out.

If corrosion, erosion or other weaknesses in the vessel are found, the vessel must be inspected by

a qualified authorised third party, who will provide the necessary permission to continue using it.

If repair is requested, approved personnel together with a qualified third party and Johnson Con-

trols Denmark will carry this out. If permission to continue using the vessel is not granted, it must

be scrapped.

Disassembly for inspection or cleaning

Before disassembly, the user must make sure that the vessel has been depressurised, vented and

drained, neutralised and/or purged of hazardous material.

Gasket connections

Gasket and gasket surface should be thoroughly cleaned and free of scratches and other defects.

The gasket should be properly positioned before attempting to retighten bolts. When a vessel is

dismantled for any cause, it must be reassembled with new gaskets. This will prevent further

leaks and/or damage to the gasket-seating surface of the vessel.

Spare parts and replacement parts

See unit spare parts.

START

Installation, operation and maintenance manual - GHUR intermediate cooler

6/6 012051 en 2021.02

GHUR intermediate cooler

Environmentally correct removal

The vessel does not contain environmentally damaging material such as asbestos, mercury or

heavy metals.

All parts of the vessel can be re-used after being scrapped.

• Refrigerant and oil must be drained off before destruction

• All steel materials can be used again after remelting

• During the remelting process, the coating will disappear without harming the

environment.

Johnson Controls Denmark ApS

SABROE Factory

Christian X's Vej 201 ∙ 8270 Højbjerg

Denmark

Phone +45 87 36 70 00

www.sabroe.comVersion 2

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Johnson Controls Zubehör Handbücher

Johnson Controls

Johnson Controls NS Series Bedienungsanleitung

Johnson Controls

Johnson Controls WRZ-TTB0000-5 Bedienungsanleitung

Johnson Controls

Johnson Controls WRZ Series Bedienungsanleitung

Johnson Controls

Johnson Controls NS-AP Series Bedienungsanleitung

Johnson Controls

Johnson Controls NS Series Bedienungsanleitung

Johnson Controls

Johnson Controls TE-6300F Series Bedienungsanleitung

Johnson Controls

Johnson Controls NS Series Bedienungsanleitung

Johnson Controls

Johnson Controls NS Series Bedienungsanleitung

Johnson Controls

Johnson Controls NS Series Bedienungsanleitung

Johnson Controls

Johnson Controls NS Series Bedienungsanleitung

Johnson Controls

Johnson Controls WRZ-SST-110 Bedienungsanleitung

Johnson Controls

Johnson Controls WRZ-SST-120 Bedienungsanleitung

Johnson Controls

Johnson Controls 2951J-COPTIR Bedienungsanleitung

Johnson Controls

Johnson Controls NS Series Bedienungsanleitung

Johnson Controls

Johnson Controls NS Series Bedienungsanleitung

Johnson Controls

Johnson Controls RS-7000 Bedienungsanleitung

Johnson Controls

Johnson Controls WRZ Series Bedienungsanleitung

Johnson Controls

Johnson Controls RS-7000 Bedienungsanleitung

Johnson Controls

Johnson Controls NS-AHN700 Series Bedienungsanleitung

Johnson Controls

Johnson Controls LN Series Bedienungsanleitung

Johnson Controls

Johnson Controls NS Series Bedienungsanleitung

Johnson Controls

Johnson Controls NS-DTN7043-2 Bedienungsanleitung

Johnson Controls

Johnson Controls S1-1NP0703 Bedienungsanleitung

Johnson Controls

Johnson Controls TE-7800 Series Bedienungsanleitung

Beliebte Zubehör Handbücher anderer Marken

Hillco

Hillco 2810 Bedienungsanleitung

Siemens

Siemens QSA2700D Bedienerhandbuch

Contours

Contours ZY024 Bedienungsanleitung

Saivod

Saivod VS621 Bedienungsanleitung

Virtuox

Virtuox VirtuCLEAN 2.0 Bedienungsanleitung

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Bedienungsanleitung

Z-Wave

Z-Wave HSD-200Z Bedienungsanleitung

turck

turck FMX-IM-2UPLI63FX Bedienungsanleitung

Decagon Devices

Decagon Devices 10HS Bedienungsanleitung

UPPAbaby

UPPAbaby Cup Holder Bedienungsanleitung

Elko

Elko SmartSensor Leakage Wireless Bedienungsanleitung

Grizzly

Grizzly H8371 Bedienungsanleitung

Panasonic

Panasonic HG-T Series Bedienungsanleitung

IFM Electronic

IFM Electronic Efector 250 Series Referenzhandbuch

DigiDesign

DigiDesign 888/24 I/O Bedienungsanleitung

PROZIS

PROZIS QUAY Bedienungsanleitung

patagonia

patagonia PSI Vest Bedienungsanleitung

SFC Energy

SFC Energy EFOY GO! Bedienungsanleitung