Johnson Controls IFC-200 Referenzhandbuch
IFC-200 Technical Manual 444
Hardware Installation Section
Technical Bulletin
Issue Date 1293
© 1993 Johnson Controls, Inc. 1
Order No. 444-040
IFC-200 Hardware Installation Procedures
Hardware Installation Procedures Page 5
●
General 5
- Backbox Mounting 5
●
Power Supplies 6
- DC Power Output Connections 7
- AC Power Connections 7
- Battery Power 7
●
Output Circuits 8
- Indicating Appliance Circuits 8
- Releasing Circuits 8
●
Standard Relays 9
●
Remote Printers 9
- Installation 10
- Printer Configuration 10
- PRN-3 Setup Paper Feed Advance 11
- Keltron Printer Option 12
●
CRT-1 Configuration 12
- Function Key Programming 14
●
Wiring the Signaling Line Circuit 14
- Isolator Modules 14
- Monitor Modules 15
- Control Modules 15
- Intelligent Detectors 15
- Device Capacity 15
- SLC Resistance Measurement 16
- Isolator Module Operation 20
- SLC Shield Termination 21
2 Hardware Installation—IFC-200 Hardware Installation Procedures
●
Isolator Module 23
●
M500MJ Monitor Module 23
- SLC Connections 23
- NFPA Style B Initiating Device Circuit 24
- NFPA Style D Initiating Device Circuit 24
- Test Switch 24
●
M501MJ Monitor Module 24
- NFPA Style B Initiating Device Circuit 25
●
M502MJ 25
- SLC Connections 25
- NFPA Style B Initiating Device Circuit 25
- NFPA Style D Initiating Device Circuit 26
●
Control Module 30
- SLC Connections 30
- NFPA Style Y Indicating Appliance Circuit 30
- NFPA Style Z Indicating Appliance Circuit 30
- Indicating Appliance Power 31
- Test Switch 31
- SLC Connections 31
- Contact Connections 31
●
Addressable Manual Pull Station 34
- BGX-101L Installation 34
●
Intelligent Detectors 35
- Installation 35
●
Optional Modules 36
- Optional Module Installation 36
- RTM-8 Option Module 36
●
NR45-24 Remote Battery Charger 39
- Connecting the Primary Power Source 39
- Connecting the Secondary Power Source 39
Hardware Installation—IFC-200 Hardware Installation Procedures 3
Supply Calculations Page 43
●
AC Branch Circuit 43
●
Main Power Supply 43
- Smoke Detectors 43
- Standby Current Load on Batteries 45
- Four-Wire Detectors 45
- Alarm Current Load on Batteries 45
- Calculating Necessary Battery Size 45
Wire Requirements 47
4 Hardware Installation—IFC-200 Hardware Installation Procedures
Hardware Installation—IFC-200 Hardware Installation Procedures 5
Hardware Installation
Procedures
This IFC-200 Hardware Installation Procedures Technical Bulletin is
divided into three major sections. The Hardware Installation Procedures
section contains step-by-step instructions to help you install the hardware
related to the IFC-200 Fire Control System. The Supply Calculations
section helps you determine the required current, current loads, and power
to support the IFC-200. Specific wiring information for each circuit in the
system is found in the Wire Requirements section. Read this document
before attempting to install the IFC-200 hardware.
1. Carefully unpack the system and check for shipping damage.
2. Mount the cabinet in a clean, dry, vibration-free area where extreme
temperatures are not encountered. The area should be readily
accessible with sufficient room to easily install and maintain the
panel.
3. Locate the top of the cabinet approximately five feet above the floor
with the hinge mounting on the left.
4. Determine the number of conductors required for the devices to be
installed.
5. Pull the required conductors into the box through the knockout
provided.
All wiring should be in accordance with the National and/or Local codes
for fire alarm systems.
1. Remove the main PC board assembly by unscrewing the four screws
in the corners of the board. Set the board aside in a safe, clean place.
Avoid static discharge, which may damage the board.
2. Mark and pre-drill the four mounting bolts using the dimensions
shown in Figure 1.
3. Install two upper fasteners in wall with screw heads protruding.
4. Using upper keyholes, mount the backbox over the two screws.
Tighten the screws.
5. Install the lower two screws.
6. When location is dry and free of construction dust, reinstall the main
PC board.
General
Backbox
Mounting
6 Hardware Installation—IFC-200 Hardware Installation Procedures
1.00 14.5
12.5
0.5
9.5 16.0
200bckbx
Mounting Holes
Primary Power
120 VAC
Low Voltage
Wiring
Figure 1: IFC-200 Backbox Mounting
Note: Insert all cables from the side of the cabinet. Do not insert wiring
from the back of the cabinet. Note the entry locations of primary
120 VAC power and low voltage wiring above.
!
CAUTION: Damage may occur when removing and/or
inserting cards, modules, or interconnecting cables
while this unit is energized. Several different
power sources can be connected to this panel.
Disconnect all power sources before servicing.
Power Supplies
Hardware Installation—IFC-200 Hardware Installation Procedures 7
All DC power outputs are power-limited.
High Ripple Regulated Power
24 VDC power for indicating appliances
TB1 Terminal 1 (+) and 2 (-).
Note: This power is unsuitable for all
RS-485 annunciation devices,
except the ACM-8R.
1.0 amps standby
2.25 amps alarm
Non-resettable Power
24 VDC filtered, regulated,
non-resettable power can be
drawn from TB1 Terminals 3 (+)
and 4 (-). This power is suitable
for all RS-485 annunciation
devices. 0.50 amps
4-wire Smoke Detector Power
24 VDC filtered, regulated,
resettable power for 4-wire smoke
detectors can be obtained from TB1
Terminals 5 (+) and 6 (-). 0.50 amps
dcpowr
T
B
1
1 2 3 4 5 6
+ - + - + -
Figure 2: DC Power Output Connections
Primary power required for this panel is 120 VAC, 50/60 Hz, 3.0 amps.
Overcurrent protection for this circuit must comply with Article 760 of the
National Electrical Code (NEC) and/or local codes. Use 14 AWG or
larger wire with 600 volt rating.
AC Power Battery
Power
acbatpwr
+
_
Figure 3: AC Power Connections and Battery Power
Observe polarity when connecting the battery. Connect the battery cable
to J3 on the main board using the plug-in connector provided. An MTA
connector tool is required. Refer to Figure 1 in the IFC-200 System
Description Technical Bulletin in this manual for the location of J3. See
the Supply Calculations section of this document to calculate the correct
battery rating.
!
CAUTION: Sulfuric acid in batteries can cause severe burns to the
skin and eyes and can destroy fabrics. If contact is
made with sulfuric acid, immediately flush skin or
eyes with water for 15 minutes and seek immediate
medical attention.
DC Power Output
Connections
AC Power
Connections
Battery Power
8 Hardware Installation—IFC-200 Hardware Installation Procedures
The IFC-200 provides four indicating appliance circuits (Style Y only).
Each circuit is capable of producing 2.25 amps of current at 24 VDC.
Total current drawn from these, as well as any other panel DC power
outputs, cannot exceed 5.0 amps. Use UL Listed 24 VDC indicating
appliances only. Circuits are supervised and power-limited. See
Figure 23 for a list of recommended compatible indicating appliances.
Any or all of these circuits may be used as a releasing circuit by
programming it for RELEASE CKT. See the Releasing Applications
section of the IFC-200 Applications Technical Bulletin in this manual for
more information, including a list of compatible solenoid valves.
T
B
2
B+ B- B+ B- B+ B- B+ B-
1 2 3 4 5 6 7 8
+ -
+ -
+ -
Style Y Indicating Appliance Circuit (Supervised and Power-limited)
Polarized Bell
Polarized Strobe
Polarized Horn
4.7K, 1/2 W (Part No. 71252, UL Listed)
(Supervisory Voltage is 2-3 VDC)
Releasing Circuit
(Supervised and Power Limited)
Dummy Load
All Unused
Circuits 4.7K, 1/2 W
Note: Indicating circuit polarity is shown in the
alarm
state.
tb2conn
Circuit 1 TB2 1 and 2
Circuit 2
Circuit 3
Circuit 4
TB2 3 and 4
TB2 5 and 6
TB2 7 and 8
Figure 4: Circuit Connections
Output Circuits
Indicating
Appliance
Circuits
Releasing
Circuits
Hardware Installation—IFC-200 Hardware Installation Procedures 9
The IFC-200 provides a set of Form-C alarm contacts and a set of Form-C
trouble contacts rated for 2.0 amps at 30 VDC (resistive). The panel also
provides a Form-A supervisory contact rated for 2.0 amps at 30 VDC
(resistive). These contacts are derated to 0.5 amps at 30 VAC.
T
B
3
NO C NO NC C NO NC C
tb3conn
1 2 3 4 5 6 7 8
SUPV ALARM TROUBLE
Figure 5: Relay Connections
The PRN-3 Remote Printer provides a hardcopy printout of all status
changes within the system and time-stamps the printout with the current
time of day and date. The PRN-3 provides 80 columns of data on standard
9 inch by 11 inch tractor-feed paper.
3 2 17
TX REF RX REF OUT OUT IN IN A B B+- A+- B- A-
T
B
4
T
B
5
T
B
6
Plug this DB-25 connector into the
RS-232 printer port.
Connect CRT-1 pin 3 to TB4 TX.
Connect CRT-1 pin 7 to TB4 REF.
Connect CRT-1 pin 2 to TB4 RX.
PRN-3
prn3conn
PRN-3
IFC-200
System Common (-)
IFC-200, TB1-2, or Enclosure
Figure 6: Remote Printer Connections
Standard
Relays
Remote Printers
10 Hardware Installation—IFC-200 Hardware Installation Procedures
Note: The RS-232 printer interface may also be used with EDP-listed
equipment, such as personal computers, to monitor the IFC-200 for
supplementary purposes.
Since the IFC-200 is not the receiving unit in a proprietary system, its use
is optional from a standards compliance standpoint. Remote printers
require 120 VAC, 50/60 Hz primary power. A secondary power source
(battery backup) is not provided; the use of a separate Uninterruptible
Power Supply (UPS), UL Listed for Fire Protection Signaling is
recommended.
The IFC-200 and PRN-3 connect via an RS-232 interface. A custom cable
must be assembled for connection to the printer’s RS-232 port.
Refer to the documentation supplied with the PRN-3 for instructions on
the printer’s menu controls. Set the printer’s options as listed in Table 1.
Table 1: PRN-3 Printer Options
Under the Menu Area:
Character Density 10 CPI
Character Presentation
Character Set Standard
Italic No
Proportional No
Slashed Zero Yes
Courier ISO/PC/Epson 0
National Character 11 (E-US ASCII)
Line Density 6 LPI
Paper Form 11
Skip Over Fold 0.5
Printer Options
Paper Options No Option
Selected Paper Path Push Tractor
Ribbon Options No Option
Left Margin 1
Right Margin 80
Horizontal Tabs 25
No Vertical Tabs Set
Top Margin Top of Form
Bottom Margin 10.5 Inches
Vertical Alignment 12-1/72 Inches
Under the Technical Listing Area:
Auto PrintPrint Commands CR
CR Implies LF No
Continued on next page . . .
Installation
Printer
Configuration
Andere Handbücher für IFC-200
2
Inhaltsverzeichnis
Andere Johnson Controls Bedienfeld Handbücher
Johnson Controls
Johnson Controls S1-TTSCC01 Kurzanleitung
Johnson Controls
Johnson Controls IFC-200 Bedienungsanleitung
Johnson Controls
Johnson Controls Frick QUANTUM Series Leitfaden
Johnson Controls
Johnson Controls IFC-3030 Bedienungsanleitung
Johnson Controls
Johnson Controls FRICK QUANTUM HD Leitfaden
Johnson Controls
Johnson Controls FRICK QUANTUM HD Handbuch
Johnson Controls
Johnson Controls IQ Panel Bedienungsanleitung
Johnson Controls
Johnson Controls FC-2000 Bedienungsanleitung
Johnson Controls
Johnson Controls Bentel Security Absoluta 630 4.10 Benutzerhandbuch
Johnson Controls
Johnson Controls T20 Bedienungsanleitung
Johnson Controls
Johnson Controls CIW01 Bedienungsanleitung
Johnson Controls
Johnson Controls IFC-3030 Bedienungsanleitung
Johnson Controls
Johnson Controls FRICK QUANTUM LX AcuAir Leitfaden
Johnson Controls
Johnson Controls Frick QUANTUM LX Bedienungsanleitung
Johnson Controls
Johnson Controls FRICK QUANTUM LX AcuAir Gebrauchs- und Pflegehandbuch
Johnson Controls
Johnson Controls Qolsys IQPK048 Bedienungsanleitung
Johnson Controls
Johnson Controls S1-TTSCC01 Leitfaden
Johnson Controls
Johnson Controls IFC-200 Bedienungsanleitung
Johnson Controls
Johnson Controls IFC-3030 Betriebsanleitung
Johnson Controls
Johnson Controls Frick QUANTUM LX Leitfaden
Johnson Controls
Johnson Controls FC-2000 Bedienungsanleitung
Johnson Controls
Johnson Controls YORK OPTIVIEW CONTROL CENTER Bedienungsanleitung
Johnson Controls
Johnson Controls Bentel Security tyco ABSOLUTA Plus Benutzerhandbuch
Johnson Controls
Johnson Controls Frick QUANTUM HD VILTER Bedienungsanleitung
