Johnson LDM195 Bedienungsanleitung

195′Laser Distance Meter w/Angle Sensor

Model No. LDM195

Instruction Manual

Congratulations on your choice of this Laser Distance Meter. We suggest

you read this instruction manual thoroughly before using the instrument

and save this instruction manual for future use.

This is a Class II laser tool and is manufactured to comply with CRF 21,

parts 1040.10 and 1040.11 as well as international safety rule IEC 285.

The laser also complies with EMC Test according to EN61000-6-3;

2001+A11:2004, EN 6100-6-1:2011, EN 6100-4-2, EN 61000-4-3, EN

60825, FCC Test according to PART 15.

2162i-3_Manuals 8/22/17 9:23 AM Page 1

Table of Contents

1. Kit Contents

2. Features and Functions

3. Safety Instructions

4. Location/Content

of Warning Labels

5. Location of Parts/Components

6. Battery Installation

7. Operating Instructions

8. Tips from the Pros

9. Care and andling

10. Troubleshooting Guide

11. Technical Specifications

12. Product Warranty

13. Warranty Registration

14. Accessories

1. Kit Contents

Description Qty.

Laser Distance Meter 1

“AAA” Alkaline Batteries 2

Wrist Strap 1

Soft-Sided Pouch 1

Quick Start Guide 1

2162i-3_Manuals 8/22/17 9:23 AM Page 2

2. Features and Functions

• Seven (7) measurement modes: Length (Single or Continuous),

Area, Volume, 2-Point Pythagoras, 1-Point Pythagoras, Digital Level

and Stake-out

• Displays in English or metric units with decimals or fractions

(English units only)

• ISO 16331-1 tested* to typical accuracy of ±1/16

″

(0.0625

″

, or 1.5mm)

• igh-speed microprocessor for quick, accurate calculations

• IP 54 protection – sealed from dust and rainwater

* This tool is tested in accordance with ISO 16331-1 “Laboratory

procedures for testing surveying and construction instruments –

Part 1: Performance of handheld laser distance meters.” This standard is

used to calculate accuracy under varying ambient lighting conditions.

For more detailed test results, see the Technical Specifications section of

this operator’s manual.

2162i-3_Manuals 8/22/17 9:23 AM Page 3

3. Safety Instructions

Please read and understand all of the following instructions, prior

to using this tool. Failure to do so, may void the warranty.

DANGER!

Class II Laser Product

Max. Power Output: ≤1mW

Wavelength: 640-660nm

THIS TOOL EMITS LASE ADIATION.

DO NOT STA E INTO BEAM.

AVOID DI ECT EYE EXPOSU E.

ATTENTION IMPORTANT

• Read all instructions prior to operating this laser tool. Do not remove any labels from tool.

• Do not stare directly at the laser beam.

• Do not project the laser beam directly into the eyes of others.

• Do not set up laser tool at eye level or operate the tool near a reflective surface as

the laser beam could be projected into your eyes or into the eyes of others.

• Do not place the laser tool in a manner that may cause someone to unintentionally

look into the laser beam. Serious eye injury may result.

• Do not operate the tool in explosive environments, i.e. in the presence of gases or

flammable liquids.

• Keep the laser tool out of the reach of children and other untrained persons.

• Do not attempt to view the laser beam through optical tools such as telescopes as

serious eye injury may result.

• Always turn the laser tool off when not in use or left unattended for a period of time.

• Remove the batteries when storing the tool for an extended time (more than 3 months)

to avoid damage to the tool should the batteries deteriorate.

• Do not attempt to repair or disassemble the laser tool. If unqualified persons attempt

to repair this tool, warranty will be void.

• Use only original Johnson®parts and accessories purchased from your Johnson®

authorized dealer. Use of non-Johnson®parts and accessories will void warranty.

2162i-3_Manuals 8/22/17 9:23 AM Page 4

4. Location/Content of Warning Labels

Error Code Label

The LDM may return an error code during use, as

indicated by the display showing “ERR X,” where

“X” represents a number from 1 to 6.

The error codes are as follows:

1. Laser Range – The measurement distance is

outside the range listed in the specifications.

2. Weak Signal – The reflected laser signal is too

weak, either due to high ambient lighting at the

target or poor target reflectivity.

3. Display Range – The measurement distance,

area or volume exceeds the number of units the

display is capable of showing.

4. Low Battery – The batteries need to be replaced.

5. Temperature – The tool is either above the

maximum or below the minimum safe operating

temperature range.

6. Ambient Light – The tool is being used in too

bright of an environment to operate properly.

QR Code: Use a smartphone to scan the QR code to

be taken directly to Johnson Level & Tool’s

Operator’s Manual Page.

2162i-3_Manuals 8/22/17 9:23 AM Page 5

5. Location of Parts/Components

LCD Screen

Subtraction Button

Addition Button

Power Button

Press for:

• Power on

• Set units of

measurement

Press and hold for:

• Power off

Measure Button

Press for:

• Power on

• Measure

Press and hold for:

• Continuous mode

Functions / Sound Button

Press for:

• Area measurement

• Volume measurement

• 2-Point Pythagoras

measurement

• 1-Point Pythagoras

measurement

Press and hold for:

• Sound ( igh, Low, Off)

Reference Button

Press for:

• Adjust the

measurement

reference

Laser Emitted Window

Laser Receiving Window

2162i-3_Manuals 8/22/17 9:23 AM Page 6

Not all features found on the LCD screen are found in every Johnson

Level & Tool Laser Distance Meter. See the notes below for further

information.

Notes:

* Feature available in the LDM330 only.

† Feature available in the LDM195 and LDM330 only.

∆ Feature found in the LDM130 and LDM330 only.

‡ Feature found in the LDM130, LDM195 and LDM330 only.

1. Measurement Reference Position

2. Measuring Mode

3. Memory (recent measurements)*

4. Active Laser Indicator

5. Add and Subtract‡

6. Maximum Display

7. Indirect Measuring Mode

(Pythagoras Measurements)‡

8. Minimum Display

9. Stake-out Direction Indicator†

10. Main Screen –

Current Measurement

11. Countdown Timer*

12. Bluetooth®Indicator∆

13. Battery Status Indicator

14. Secondary Screens

(prior 2 measurements)

LCD Screen

2162i-3_Manuals 8/22/17 9:23 AM Page 7

6. Battery Installation

To install batteries in the Laser Distance Meter:

Remove the battery cover by lifting the cover

straight up from the bottom of the Laser

Distance Meter as shown by the arrow in the

image to the right.

2. Insert 2 “AAA” batteries into the battery

compartment according to the polarity

illustrated inside.

3. Replace the battery cover.

Current Battery Status

To check the current battery life, press and hold both the and

buttons simultaneously for one second. The battery icon will display

for approximately 10 seconds.

When the batteries are low, the battery icon will automatically display.

Battery has 100% power

Battery has approximately 60% power

Battery has approximately 25% power

Battery has approximately 5% power,

and new batteries are needed

Notes:

• Use only alkaline batteries.

• Remove the batteries when storing the instrument for an extended

time (more than 3 months) to avoid damage to the tool should the

batteries deteriorate.

2162i-3_Manuals 8/22/17 9:23 AM Page 8

7. Operating Instructions

IMPO TANT: It is the responsibility of the user to ensure proper

maintenance of the Laser Distance Meter. Conduct periodic test

measurements to ensure the instrument is measuring accurately

and consistently. This is most important if the instrument has been

exposed to extreme temperatures or moisture. Always confirm

accuracy before and during important measurements. Keep the

Laser Distance Meter optic lens clean and inspect for damage.

The Laser Distance Meter is designed to withstand a drop from

3 feet (1 meter). If dropped from a higher distance, the tool’s

calibration may be affected and it should be tested for accuracy.

Power On/Off the Laser Distance Meter

Press either the button or the button to power on the

instrument.

Press and hold the button to power off the instrument.

Auto atic Shutoff

Laser will turn off after remaining idle for 2 minutes. Press the

button to re-enable the laser.

Unit will turn off after remaining idle for 5 minutes.

2162i-3_Manuals 8/22/17 9:23 AM Page 9

Volu e Control

The Laser Distance Meter has three volume settings: high, low and

off. When the instrument is powered on, it will default to the most

recently used volume setting.

To change the volume setting, press and hold the button.

The unit will cycle through the three settings (S1 = high, S-2 = low,

Off = mute) until you release the button.

Measuring Modes

The Laser Distance Meter has 7 measuring modes. When the instrument

is powered on, it will default to the Length measuring mode.

1. Length (Single or Continuous)

2. Square

3. Volume/Cube

4. 1-Point Pythagoras

5. 2-Point Pythagoras

6. Stake-out

7. Digital Level

To select a mode, press the button. When there is no measuring

mode icon shown near the top left of the LCD screen, the instrument

is in the Length measuring mode. The selected measuring mode icon

will display near the top left of the LCD screen for the Area, Volume,

1-Point Pythagoras and 2-Point Pythagoras measuring modes. When

in the stake-out mode, the main display will have a flashing

symbol and will read 0.00, with the hundredths decimal place flashing.

2162i-3_Manuals 8/22/17 9:23 AM Page 10

Inhaltsverzeichnis

Andere Johnson Messgerät Handbücher

Johnson

Johnson 40-6676 Bedienungsanleitung

Johnson

Johnson 40-6515 Bedienungsanleitung

Johnson

Johnson 40-6526 Bedienungsanleitung

Johnson

Johnson 40-6526 Bedienungsanleitung

Johnson

Johnson 40-6001 Bedienungsanleitung

Johnson

Johnson 40-6590 Bedienungsanleitung

Johnson

Johnson 40-6625 Bedienungsanleitung

Johnson

Johnson 40-6700 Bedienungsanleitung

Johnson

Johnson Old Town Sportsman iPilot Bedienungsanleitung

Johnson

Johnson 40-6705 Bedienungsanleitung

Johnson

Johnson 40-6519 Bedienungsanleitung

Johnson

Johnson LDM150 Bedienungsanleitung

Johnson

Johnson 40-6582 Bedienungsanleitung

Johnson

Johnson JLX 40-6590 Bedienungsanleitung

Johnson

Johnson 1888-0700 Bedienungsanleitung

Johnson

Johnson 1456-0000 Bedienungsanleitung

Johnson

Johnson 40-6543 Bedienungsanleitung

Johnson

Johnson JRT300-RDHV-S Bedienungsanleitung

Johnson

Johnson 40-6527 Bedienungsanleitung

Johnson

Johnson 1888-1100 Bedienungsanleitung

Johnson

Johnson LEVEL UP 40-6535 Bedienungsanleitung

Johnson

Johnson 40-6618 Bedienungsanleitung

Johnson

Johnson 1889-0600 Bedienungsanleitung

Johnson

Johnson 40-6688 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung