Juniper QFX10016 Bedienungsanleitung

Quick Start

QFX10016 Quick Start

IN THIS GUIDE

Step 1: Begin | 1

Step 2: Up and Running | 19

Step 3: Keep Going | 22

Step 1: Begin

IN THIS SECTION

Meet the QFX10016 | 2

Prepare the Site for the QFX10016 | 2

Unpack the QFX10016 | 4

Mount the Switch Chassis | 5

Install the QFX10016 | 7

Install the Line Cards | 10

Install the Front Panel | 11

Connect Power to the Chassis | 13

In this guide, we provide a simple, three-step path, to quickly get you up and running with the Juniper Networks®

QFX10016 switch. You'll learn how to install, power on, and congure basic sengs for both AC-powered and DC-

powered QFX10016 switches.

Meet the QFX10016

The QFX10016 is a rigid sheet-metal switch-chassis that houses eld -replaceable units (FRUs) such as control boards,

Switch Interface Boards (SIBs), power supplies, fan trays, and line cards. The switch chassis ships in a cardboard box that

has a two-layer wooden pallet base. The switch chassis is bolted to the pallet base. You can install a QFX10016 switch

in a standard 19 in. (48.26 cm) equipment rack by using the supplied rack-mounng kit and the front-mounng bracket

that is aached to the chassis.

Before you install the QFX10016, make sure the site meets all the power, cooling, and clearance requirements. See the

site preparaon guidelines and power requirements in the QFX10016 Switch Hardware Guide.

Prepare the Site for the QFX10016

IN THIS SECTION

Rack-Mounng Requirements | 2

Clearance Requirements | 3

Cooling and Airow Requirements | 3

Rack-Mounng Requirements

The QFX10016 switch chassis is designed to be installed in standard 19-in. wide four-post racks that are spaced at 1 U

(1.75 in. or 4.45 cm) increments.

You can stack two QFX10016 chassis in a four-post rack if:

• The rack is 42 U or greater.

• The rack meets the strength requirements to support the weight.

• The facility can provide adequate power and cooling.

Before installing the chassis, ensure that:

• The rack rails are spaced widely enough to accommodate the switch chassis’ external dimensions. The outer edges of

the front-mounng brackets extend the chassis width to 19 in. (48.26 cm).

• The rack is strong enough to support the weight of the switch and cabling.

• The spacing of rails and adjacent racks allows for proper clearance around the switch and rack.

Clearance Requirements

For the cooling system to funcon properly, the airow around the chassis must be unrestricted. You must allow

sucient clearance around the installed chassis for cooling and maintenance.

If you are mounng a QFX10016 in a rack with other equipment, ensure that the exhaust from other equipment does

not blow into the intake vents of the chassis.

Cooling and Airow Requirements

The cooling system in a QFX10016 chassis consists of dual fan trays and dual fan tray controllers. There is no air lter in

a QFX10016.

The air intake to cool the chassis is located on the port (line card) side of the chassis. Air ows into the chassis from the

ports in the control boards and line cards, through the Switch Interface Boards (SIBs), and exits from the fan trays and

the power supplies. This airow is called port-to-FRU cooling or airow out (AFO).

Follow these guidelines:

• For the cooling system to funcon properly, the airow around the chassis must be unrestricted.

• If you are mounng a QFX10016 in a rack with other equipment, ensure that the exhaust from other equipment

does not blow into the intake vents of the chassis.

• Leave at least 24 in. (61 cm) both in front of and behind the QFX10016 for service personnel to remove and install

hardware components. To be NEBS GR-63 compliant, allow at least 30 in. (76.2 cm) in front of the rack and 24 in. (61

cm) behind the rack.

Unpack the QFX10016

Here’s how to unpack the chassis for QFX10016:

1. Move the shipping box to a staging area as close to the installaon site as possible. While the chassis is bolted to

the pallet, you can use a forkli or pallet jack to move it. Make sure there is enough space to remove components

from the chassis.

2. Posion the shipping box with the arrows poinng up.

3. Slice the nylon straps with the box cuer that hold the shipping boxes to the pallet.

4. Li the shipping box o the chassis.

5. Remove the cardboard accessory box.

6. Remove the foam padding from the top of the box.

7. Remove the plasc cover from the switch chassis.

8. Use a 13/32 in. (10 mm) open-end or socket wrench to remove the four sets of bracket bolts that secure the

chassis to the shipping pallet.

9. Unpack the accessory box and lay out the contents so that they are ready for use.

10. Verify that your order includes all appropriate parts.

11. Store the brackets and bolts inside the accessory box.

12. Save the shipping box and packing materials in case you need to move or ship the switch at a later me.

Mount the Switch Chassis

IN THIS SECTION

Install the Mounng Hardware | 5

Mount the QFX10016 using a Mechanical Li | 6

To install the QFX10016, rst install the mounng hardware and then use a mechanical li to load the chassis into the

rack.

•"Install the Mounng Hardware" on page 5

•"Mount the QFX10016 using a Mechanical Li" on page 6

Install the Mounng Hardware

Install the mounng hardware on the rack before installing the switch. The QFX10016 comes with a four-piece set of

mounng brackets that support the chassis in the rack.

NOTE: Two-post installaon racks are not supported.

When you install the mounng brackets, the adjustable poron of the brackets overlap. Use the overlap area to adjust

the total bracket length to t any of the four standard rack sizes: 19 in. (483 mm), 23.62 in. (600 mm), 30 in. (762 mm),

or 31.5 in. (800 mm).

To install the mounng brackets in a four-post rack:

1. Remove the mounng brackets from the accessory box.

2. Decide where to place the chassis in the rack. If the rack is empty, mount the switch in the lowest possible locaon.

See "Rack-Mounng Requirements" on page 2.

3. Posion the le front adjustable mounng bracket at the desired posion in the le side of the rack and line up its

front screw holes with the holes in the rack. Use four mounng screws appropriate for your rack to aach the le

front bracket to the rack.

4. Posion one of the rear brackets at the le rear of the rack on the same level as the le front bracket, so that the

rear bracket overlaps with the le front bracket. The screw holes for connecng the front and rear brackets should

overlap. Use four mounng screws appropriate for your rack to aach the rear bracket to the rack.

5. Connect le front and rear brackets.

a. Insert six of the screws provided with the mounng brackets into the overlapping bracket holes.

b. Hand-ghten the screws fully (to 12–16 in.-lb torque) using a number 2 Phillips screwdriver.

6. Posion the right front adjustable mounng bracket at the desired posion in the right side of the rack opposite the

installed le front bracket, so that it is on the same rack level as the le bracket. If the right and le front brackets

are not on the same level, the chassis will rest at an angle in the rack instead of resng at and level. Line up the

right bracket's front screw holes with the holes in the rack. Use four mounng screws appropriate for your rack to

aach the right front bracket to the rack.

7. Posion the other rear bracket at the right rear of the rack on the same level as the right front bracket, so that the

rear bracket overlaps with the right front bracket. The screw holes for connecng the front and rear brackets should

overlap. Use four mounng screws appropriate for your rack to aach the rear bracket to the rack.

8. Connect the right front and rear brackets.

a. Insert six of the screws provided with the mounng brackets into the overlapping bracket holes.

b. Hand-ghten the screws fully (to 12–16 in.-lb torque) using a number 2 Phillips screwdriver.

Mount the QFX10016 using a Mechanical Li

Because of the switch's size and weight, the QFX100016 can safely be installed only by using a mechanical li.

CAUTION: Do not install line cards in the chassis unl aer you mount the chassis securely on a rack or

cabinet.

CAUTION: Before front-mounng the switch on a rack or cabinet, have a qualied technician verify

that the rack or cabinet is strong enough to support the switch's weight and is adequately supported at

the installaon site.

To install the switch using a mechanical li:

1. Ensure that the rack or cabinet is placed in its permanent locaon and is secured to the building. Ensure that the

installaon site allows adequate clearance for both airow and maintenance. For details, see "Cooling and Airow

Requirements" on page 3.

2. Load the switch onto the li, making sure it rests securely on the li plaorm.

3. Using the li, align the switch in front of the rack, centering it in front of the mounng brackets.

4. Li the chassis approximately 0.75 in. (1.9 cm) above the surface of the mounng brackets. Align the chassis as close

as possible to the mounng brackets.

5. Carefully slide the chassis onto the adjustable mounng brackets unl the front-mounng brackets aached to the

chassis contact the rack rails. The mounng brackets ensure that the holes in the front-mounng brackets align with

the holes in the rack rails.

6. Move the li away from the rack.

7. Install a mounng screw into each of the open front-mounng holes aligned with the rack, starng from the boom.

8. Visually inspect the alignment of the switch. If the switch is installed properly in the rack, all the mounng screws on

one side of the rack are aligned with the mounng screws on the opposite side and the switch is level.

9. Aer ensuring that the switch is aligned properly, ghten the screws.

Install the QFX10016

IN THIS SECTION

What's in the Box? | 8

What Else Do I Need? | 8

What's in the Box?

Along with your QFX10016, you’ll also nd:

• An accessory kit which includes:

• AC Power cord (country specic).

• Power cord retainer clips.

•Electrostac discharge (ESD) wrist strap with cable.

• A Phillips (+) screwdriver, number 1, 2, or 3, depending on the size of your rack-mounng screws.

•Mounng brackets. These support the chassis in the rack and are as follows:

• 1 le front mounng bracket. The bracket is labeled “LEFT FRONT” on the side of the bracket that faces the

interior of the rack, near the holes for aaching the bracket to the rack.

• 1 right front mounng bracket. The bracket is labeled “RIGHT FRONT” on the side of the bracket that faces

the interior of the rack, near the holes for aaching the bracket to the rack.

• 2 rear mounng brackets. These brackets are labeled “REAR” on the side of the bracket that faces the interior

of the rack, near the holes for aaching the bracket to the rack. The rear brackets are interchangeable; you

can use either of the rear brackets with the right or le front-mounng bracket.

• Cable lug.

• Chassis. The chassis ships in a cardboard box that has a two-layer wooden pallet base with foam cushioning

between the layers. The switch chassis is bolted to the pallet base. The shipper has the opon to either ship the

front panel separately or to ship along with the chassis. If the front panel arrives with the chassis, set aside the

front panel box unl you are ready to verify the contents of the order.

• RJ-45 connector. An RJ-45 cable and an RJ-45 to DB-9 serial port adapter are supplied with the device.

NOTE: If your laptop or PC does not have a DB-9 male connector pin and you want to connect your

laptop or PC directly to the device, use a combinaon of the RJ-45 to DB-9 female adapter supplied with

the device and a USB to DB-9 male adapter. You must provide the USB to DB-9 male adapter.

What Else Do I Need?

You’ll need:

To Unpack the QFX10016

• A 13/32 in. (10 mm) open-end or socket wrench to remove the bracket bolts from the shipping pallet.

• A box cuer or packing knife to slice open the nylon straps and tape that seal the crate and boxes.

To Install the Mounng Brackets

• A Phillips (+) screwdriver, number 2, to install the screws that connect the rear-mounng and front-mounng

brackets.

• 16 mounng screws appropriate for your rack to aach the 4 mounng bracket pieces to the rack.

To Install using a Mechanical Li

• A mechanical li rated for 1000 lbs. (453.6 kg).

• 12 mounng screws appropriate for your rack.

CAUTION: If you are installing more than one switch in a rack or cabinet, install the rst switch at the

boom of the rack.

To Install the Front Panel

• A Phillips (+) screwdriver, number 2.

• Front panel (provided with the switch chassis).

• Right base bracket (provided).

•Le base bracket (provided).

• 2 interchangeable latch brackets (provided).

• 8 Phillips at head mounng screws (provided).

To Ground the Chassis

•Protecve earthing terminal lug (provided).

• Grounding cable for your QFX10016 (not provided)—The grounding cable must be 6 AWG (13.3 mm²), minimum 90°

C wire, or as permied by the local code.

• Grounding lug for your grounding cable (provided)—This bracket aaches to the lower le corner of the QFX10016

switch chassis next to PSU 9, providing a protecve earthing terminal for the switch. The grounding lug required is a

Panduit LCD6-10A-L or equivalent.

• Any Phillips screwdriver to ghten the two screws that are mounted on the chassis.

To Install a DC Power Supply

• DC power source cables (not provided) with the cable lugs (provided) aached. The provided terminal lugs in a

QFX10016 are sized for 4 AWG (21.1 mm2) power source cables. The DC power source cables that you provide

must be 4 AWG (21.1 mm2), minimum 60°C wire. We recommend that you install heat-shrink tubing insulaon

around the crimped secon of the power cables and lugs.

• 13/32 in. (10 mm) nut driver or socket wrench.

• Phillips (+) screwdrivers, numbers 1 and 2.

•Mulmeter.

Install the Line Cards

QFX10000 line cards are eld-replaceable units (FRUs) that can be installed in any of the line card slots on the front of

the chassis. The line cards are hot-insertable and hot-removable: You can remove and replace them without powering

o the switch or disrupng switch funcons.

To install a line card in the switch chassis:

1. Aach the ESD grounding strap to your bare wrist and connect the strap to the ESD point on the switch chassis. The

ESD point is located above the status LED panel on the front of the switch chassis.

2. Remove the cover panel by grasping the handles and pulling straight out to expose the slot for the line card.

CAUTION: Do not li the line card by holding the edge connectors or the handles on the faceplate.

Neither the handles or the edge connectors can support the weight of the line card. Liing the line

Andere Handbücher für QFX10016

Inhaltsverzeichnis

Andere Juniper Netzwerk-Hardware Handbücher

Juniper

Juniper SRX5600 Bedienungsanleitung

Juniper

Juniper SSR1500 Bedienungsanleitung

Juniper

Juniper Day One+ Bedienungsanleitung

Juniper

Juniper SRX300 Series Bedienungsanleitung

Juniper

Juniper ACX7100 Bedienungsanleitung

Juniper

Juniper NFX250 Bedienungsanleitung

Juniper

Juniper NFX150 Bedienungsanleitung

Juniper

Juniper Junos Space JA2500 Montageanleitung

Juniper

Juniper SSR130 Bedienungsanleitung

Juniper

Juniper M-Series Bedienungsanleitung

Juniper

Juniper NFX250-S1 Bedienungsanleitung

Juniper

Juniper EX4100-F- 24P/T Bedienungsanleitung

Juniper

Juniper NetScreen-5GT Wireless Bedienungsanleitung

Juniper

Juniper SSR120 Montageanleitung

Juniper

Juniper NFX150-S1 Bedienungsanleitung

Juniper

Juniper Day One Plus SRX380 Bedienungsanleitung

Juniper

Juniper DUAL-PORT T1-E1 GPIMS Bedienungsanleitung

Juniper

Juniper SRX3400 Bedienungsanleitung

Juniper

Juniper SSR1200 Bedienungsanleitung

Juniper

Juniper MX150 Bedienungsanleitung

Juniper

Juniper NetScreen-IDP 3.0 Bedienungsanleitung

Juniper

Juniper EX9200 Series Bedienungsanleitung

Juniper

Juniper SRX Series Bedienungsanleitung

Juniper

Juniper SSR1400 Bedienungsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Arista

Arista CCA-ETM-Q12 Bedienungsanleitung