JVC CD Receiver KD-G417 Bedienungsanleitung

SERVICE MANUAL

2005/7

CD RECEIVER

MA20220057

KD-G417

Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade)

TABLE OF CONTENTS

1 PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

2 SPECIFIC SERVICE INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

3 DISASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7

4 ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-25

5 TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-26

Area suffix

EE -------- Russian Federation

1-2 (No.MA202)

SPECIFICATION

Design and specifications are subject to change without notice.

AUDIO AMPLIFIER SECTION

Maximum Power Output Front 50 W per channel

Rear 50 W per channel

Continuous Power Output (RMS) Front 19 W per channel into 4 Ω, 40 Hz to 20 000 Hz at no more

than 0.8% total harmonic distortion.

Rear 19 W per channel into 4 Ω, 40 Hz to 20 000 Hz at no more

than 0.8% total harmonic distortion.

Load Impedance 4 Ω(4 Ωto 8 Ωallowance)

Tone Control Range Bass ±10 dB at 100 Hz

Treble ±10 dB at 10 kHz

Frequency Response 40 Hz to 20 000 Hz

Signal-to-Noise Ratio 70 dB

Line-Out Level/Impedance 2.5 V/20 kΩload (full scale)

Output Impedance 1 kΩ

TUNER SECTION

Frequency Range FM1/FM2 87.5 MHz to 108.0 MHz

FM3 65.00 MHz to 74.00 MHz

AM (MW) 522 kHz to 1 620 kHz

(LW) 144 kHz to 279 kHz

FM Tuner Usable Sensitivity 11.3 dBf (1.0 µV/75 Ω)

50 dB Quieting Sensitivity 16.3 dBf (1.8 µV/75 Ω)

Alternate Channel Selectivity (400 kHz) 65 dB

Frequency Response 40 Hz to 15 000 Hz

Stereo Separation 30 dB

Capture Ratio 1.5 dB

MW Tuner Sensitivity 20 µV

Selectivity 35 dB

LW Tuner Sensitivity 50 µV

CD PLAYER SECTION

Type Compact disc player

Signal Detection System Non-contact optical pickup (semiconductor laser)

Number of Channels 2 channels (stereo)

Frequency Response 5 Hz to 20 000 Hz

Dynamic Range 96 dB

Signal-to-Noise Ratio 98 dB

Wow and Flutter Less than measurable limit

MP3 Decoding Format MPEG1/2 Audio Layer 3

Max. Bit Rate: 320 kbps

WMA (Windows Media Audio) Decoding Format Max. Bit Rate: 192 kbps

GENERAL

Power Requirement Operating Voltage DC 14.4 V (11 V to 16 V allowance)

Grounding System Negative ground

Allowable Operating Temperature 0°C to +40°C

Dimensions (W ×H ×D) Installation Size (approx.) 182 mm ×52 mm ×150 mm

Panel Size (approx.) 188 mm ×58 mm ×11 mm

Mass (approx.) 1.3 kg (excluding accessories)

(No.MA202)1-7

SECTION 3

DISASSEMBLY

3.1 Main body section

3.1.1 Removing the front panel assembly

(See Fig.1)

(1) Push the detach button in the lower right part of the front

panel assembly and remove the front panel assembly.

Fig.1

3.1.2 Removing the bottom cover

(See Fig.2)

(1) Turn the main body up side down.

(2) Insert a screwdriver under the joints to release the two

joints aon the left side, two joints bon the right side and

joint con the back side of the main body, then remove the

bottom cover from the main body.

Note:

When releasing the joints using a screwdriver, do not damage

the main board.

Fig.2

3.1.3 Removing the front chassis assembly

(See Fig.3)

• Remove the front panel assembly and bottom cover.

(1) Remove the two screws Aon the both sides of the main

body.

(2) Release the two joints dand two joints eon the both sides

of the main body, then remove the front chassis assembly

toward the front.

Fig.3

Front panel assembly

Detach button

Bottom cover

Joint b

Joint c

Joint a

Joint d

Front chassis assembly

Joint e

Joint d Joint e

1-8 (No.MA202)

3.1.4 Removing the side panel

(See Fig.4)

Reference:

Remove the front panel assembly as required.

(1) Remove the screw Band two screws Cattaching the side

panel on the left side of the main body.

(2) Remove the side panel from the main body.

Fig.4

3.1.5 Removing the rear bracket

(See Fig.5)

• Remove the bottom cover.

(1) Remove the three screws D, one screw Eand two screws

Fattaching the rear bracket on the back side of the main

body.

(2) Remove the rear bracket.

3.1.6 Removing the main board

(See Figs.5 and 6)

• Remove the front panel assembly, bottom cover and side pan-

el.

Reference:

Remove the front chassis assembly as required.

(1) Remove the three screws Dattaching the rear bracket on

the back side of the main body. (See Fig.5.)

(2) Remove the two screws Gattaching the main board. (See

Fig.6.)

(3) Disconnect the connector CN501 on the main board from

the main body and take out the main board with the rear

bracket. (See Fig.6.)

Reference:

Remove the rear bracket from the main body as required. (See

"3.1.5 Removing the rear bracket".)

Fig.5

Fig.6

Side panel

CBC

Rear bracket FF

Main board

CN501

Rear bracket

(No.MA202)1-9

3.1.7 Removing the CD mechanism assembly

(See Fig. 7)

• Remove the front panel assembly, bottom cover, side panel,

rear bracket and main board.

Reference:

Remove the front chassis assembly as required.

(1) Remove the three screws Hattaching the CD mechanism

assembly on the top chassis.

(2) Take out the CD mechanism assembly.

Fig.7

3.1.8 Removing the switch board

(See Figs.8 to 10)

• Remove the front panel assembly.

(1) Remove the five screws Jon the back side of the front pan-

el assembly. (See Fig.8.)

(2) Release the twelve joints fand remove the rear cover. (See

Fig.9.)

(3) Release the joint gand take out the switch board from the

front panel assembly. (See Fig.10.)

Note:

When removing the rear cover assembly and switch board, be

careful not to lose the spring.

Fig.8

Fig.9

Fig.10

CD mechanism assembly Top chassis

Joints f

Joints fJoints f

Rear cover

Switch board Joint g

Front panel assembly

1-10 (No.MA202)

3.2 CD Mechanism Assembly

3.2.1 Removing the top cover

(See Figs.1 and 2)

(1) Remove the two screws Aon the both side of the body.

(2) Lift the front side of the top cover and move the top cover

backward to release the two joints a.

Fig.1

Fig.2

Joints a

Top cover

Joints a

Top cover

(No.MA202)1-11

3.2.2 Removing the connector board

(See Figs.3 to 5)

CAUTION:

Before disconnecting the flexible wire from the pickup, solder

the short-circuit point on the pickup. No observance of this in-

struction may cause damage of the pickup.

(1) Remove the screw Bfixing the connector board.

(2) Solder the short-circuit point on the connector board.

(3) Disconnect the flexible wire from the pickup.

(4) Move the connector board in the direction of the arrow to

release the two joints b.

(5) Unsolder the wire on the connector board if necessary.

CAUTION:

Unsolder the short-circuit point after reassembling.

Fig.3

Fig.4

Fig.5

Connector board

Pickup

Short-circuit point

Joints b

Wires

Pickup

Short-circuit point

(Soldering)

Flexible wire

Connector board

Frame

1-12 (No.MA202)

3.2.3 Removing the DET switch

(See Figs.6 and 7)

(1) Extend the two tabs cof the feed sw. holder and pull out

the switch.

(2) Unsolder the DET switch wire if necessary.

Fig.6

Fig.7

Connector

board

DET switch

Pickup

DET switch Tab c

Tab c

DET switch wire

Feed sw. holder

(No.MA202)1-13

3.2.4 Removing the chassis unit

(See Figs.8 and 9)

• Prior to performing the following procedure, remove the top

cover and connector board.

(1) Remove the two suspension springs (L) and (R) attaching

the chassis unit to the frame.

CAUTION:

• The shape of the suspension spring (L) and (R) are dif-

ferent. Handle them with care.

• When reassembling, make sure that the three shafts

on the underside of the chassis unit are inserted to the

dampers certainly.

Fig.8

Fig.9

Suspension spring (L)

Suspension spring (R)

Chassis unit

Frame

Chassis unit

Frame

Shafts

Shaft

Dampe

Damper

1-14 (No.MA202)

3.2.5 Removing the clamper assembly

(See Figs.10 and 11)

• Prior to performing the following procedure, remove the top

cover.

(1) Remove the clamper arm spring.

(2) Move the clamper assembly in the direction of the arrow to

release the two joints d.

Fig.10

Fig.11

Clamper arm

spring

Chassis rivet

assembly

Joint d

Joint d Clamper assembly

Clamper arm spring

Clamper

assembly

Joint d

Chassis rivet assembly

Andere Handbücher für CD Receiver KD-G417

Andere JVC Autoempfänger Handbücher

Beliebte Autoempfänger Handbücher anderer Marken

Motorola

Motorola VWA63 Bedienungsanleitung

Nextar

Nextar D3201 Bedienungsanleitung

Alpine

Alpine CDE-163BT Bedienungsanleitung

Pioneer

Pioneer DEH-P645R Bedienungsanleitung

Axxera

Axxera XDMA7600 Betriebsanleitung

XM OnyX Bedienungsanleitung

Sound Storm

Sound Storm STM93R Bedienungsanleitung

Soundstream

Soundstream VIR-5000 Bedienungsanleitung

Avson

Avson MKT Platform Bedienungsanleitung

Sony

Sony MEX-1HD - Audio Library System Bedienungsanleitung

Pioneer

Pioneer DVH-P500UB Bedienungsanleitung

Blaupunkt

Blaupunkt SANTIAGO CR 87 Bedienungsanleitung

Sony

Sony CDX-4160 - Cd Receiver Bedienungsanleitung

XFIRE AUDIO

XFIRE AUDIO BMW42S Bedienungsanleitung

VDO

VDO CD 2253 Bedienungsanleitung

Volvo

Volvo 13 84 580 Bedienungsanleitung

ZENEC

ZENEC ZE-160DVD Bedienungsanleitung

Medion

Medion Car Audio Bedienungsanleitung