JVC KS-F363R Bedienungsanleitung

SERVICE MANUAL

CASSETTE RECEIVER

No.49686

Feb. 2002

KS-F363R/KS-F360R

Area Suffix

Continental Europe

Central Europe

KS-F363R

KS-F360R

KS-F363R

KS-F360R

Contents

Safety precaution

Disassembly method

Adjustment method

Description of major ICs

1- 2

1- 3

1-12

1-16~22

Different pont Illumination

KS-F363R Amber

KS-F360R Green

KS-F363R/KS-F360R

1-2

!Burrs formed during molding may be left over on some parts of the chassis. Therefore,

pay attention to such burrs in the case of preforming repair of this system.

Safety precaution

KS-F363R/KS-F360R

1-3

Press the eject button in the lower right part of the

front panel. Remove the front panel assembly from

the body.

Removing the front panel assembly

(See Fig.1)

Prior to performing the following procedure, remove

the front panel assembly.

Release the four joint tabs aon both sides of the

front chassis assembly and remove the front chassis

assembly toward the front.

Removing the front chassis assembly

(See Fig.2 and 3)

Disassembly method

Fig.1

Fig.2

Fig.3

Front panel assembly

Eject button

Tab a

Front chassis assembly

Front chassis

assembly

Heat sink Tab a

Tab a

KS-F363R/KS-F360R

1-4

Remove the three screws Aon the left side of the

body.

Removing the heat sink (See Fig.4)

Prior to performing the following procedure, remove

the front panel assembly, the front chassis assembly

and the heat sink.

Turn over the body and unjoint the five joints bwith

the bottom cover and the body using a screwdriver.

Removing the bottom cover

(See Fig.5 and 6)

Fig.4

Fig.5

Fig.6

Heat sink

Joints b

Joint b

Joints b

Joint b

Bottom cover

Rear panel

KS-F363R/KS-F360R

1-5

Prior to performing the following procedure, remove

the front panel assembly, the front chassis assembly,

the heat sink and the bottom cover.

Remove the screw B, the screw C and the two

screws Dattaching the rear bracket on the back of

the body. Remove the rear panel.

Remove the two screws Eattaching the main board

on the bottom of the body. Disconnect connector

CN901,CN902 on the main board in the direction of

the arrow.

Removing the main board

(See Fig.7 and 8)

Prior to performing the following procedure, remove

the front panel assembly, the front chassis assembly,

the heat sink, the bottom cover and the main board.

Remove the four screws Fattaching the cassette

mechanism section on the back of the top chassis.

Removing the cassette mechanism section

(See Fig.9)

Fig.7

Fig.8

Fig.9

Rear panel

Main board

CN901

CN902

Cassette mechanism section

Top chassis

KS-F363R/KS-F360R

1-6

Prior to performing the following procedure, remove

the front panel assembly.

Remove the four screws Gattaching the rear cover

on the back of the front panel assembly.

Unjoint the nine joints cwith the front panel and the

rear cover.

Remove the control switch board on the back of the

front panel.

Removing the control switch board

(See Fig.10 to 12)

Fig.10

Fig.11

Fig.12

G G

Rear cover

Joints c

Front panel

Rear cover

Front panel

Control switch board

KS-F363R/KS-F360R

1-7

Prior to performing the following procedures, remove

the head amplifier board, the relay board and the

mechanism bracket.

Unsolder the three wires aon the direction switch

board.

Remove the one screw Aattaching the direction

switch board.

Removing the direction switch board

(See Fig.1)

Remove the screw Battaching the FF / REW lever

assembly on the back of the cassette mechanism

assembly.

Remove the screw Con the upper side of the FF /

REW lever assembly.

Lift and pull forward the FF / REW lever assembly to

disengage the joints b, c, dand e.

Removing the FF / REW lever assembly

(See Fig.1)

Reattach the FF / REW lever assembly to the joint c

on the back of the chassis.

Reattach the pinch-roller shaft e, the change lever d

and the return link eto the chassis.

Reattaching the FF / REW lever assembly

(See Fig.1)

FF / REW lever assembly

Joint c

Joint b

Direction switch board

Joint d

Joint e

Soldering a

Fig.1

KS-F363R/KS-F360R

1-8

Prior to performing the following procedure, remove

the direction switch board and the FF / REW lever

assembly.

Remove the screw Dattaching the playback head.

Remove the C washer and pull out the FF roller.

Remove the S support plate, the A arm spring (a)

and (b), the playback head.

Removing the playback head (See Fig.2)

The A arm spring (a) differs from the A

arm spring (b).

ATTENTION:

Prior to performing the following procedure, remove

the direction switch board and the FF / REW lever

assembly.

Remove the P arm spring (f) in the pinch-roller (F)

assembly from the chassis.

Remove the P arm spring (r) in the pinch-roller (R)

assembly from the chassis.

Draw out the pinch roller (F) and (R) assembly from

the shaft.

Removing the pinch-roller (R) and (F)

assembly (See Fig.2)

The P arm spring (f) differs from the P

arm spring (r).

ATTENTION:

The pinch roller (F) assembly differs

from the pinch roller (R) assembly.

ATTENTION:

A arm spring (b) A arm spring (a)

Pinch-roller (R) assembly Pinch-roller (F) assembly

Shaft Shaft

S support plate

C washer

P arm spring (f)

P arm spring (r)

Remove the P arm spring (f)

from the chassis.

Remove the P arm spring (r)

from the chassis.

Playback head

FF roller

Fig.2

KS-F363R/KS-F360R

1-9

Prior to performing the following procedure, remove

the FF / REW lever assembly.

From the rear of the unit, bend the two tabs f

outwards and disengage the two joints gin the

direction of the arrow.

Push the eject lever and remove the cassette holder

from the playback head. Disengage the two joints h

of the cassette hanger / cassette holder and the eject

lever in the direction of the arrow.

Lift the cassette hanger / cassette holder and disengage

the joint iof the return link and the eject lever.

Removing the cassette hanger / cassette

holder (See Fig.3)

Unsolder the two wires jon the motor assembly.

Turn over the cassette mechanism assembly and

remove the main belt and the sub-belt from the

motor pulley.

Remove the two screws Gattaching the motor

assembly.

Removing the motor assembly

(See Fig.5)

To replace the sub-belt, remove the

main belt and the sub-belt from the

motor pulley. Then remove the three

screws Eand one screw F. Replace

with a new sub-belt while lifting the reel

base assembly slightly.

ATTENTION:

Prior to performing the following procedure, remove

the FF / REW lever assembly and the cassette

hanger / cassette holder.

Remove the C washer and pull out reel disc assembly.

Removing the reel disc assembly

(See Fig.4)

Replace with a new C washer when

reattaching.

ATTENTION:

The main belt can now be removed.

ATTENTION:

Cassette holder

Cassette hanger

Return link

Joint i

Eject lever

Joint h

Joint g

Joint g Tab f

Tab f

Reel disc assembly

Flywheel (BF)

Flywheel (BR)

Main-belt

Reel base assembly

Sub-belt

Motor assembly

Motor pulley

Soldering j

Fig.3

Fig.4

Fig.5

C washer

Chassis

KS-F363R/KS-F360R

1-10

Raise the part kof the reel base assembly slightly

and remove the selector link (B) on the front side of

the cassette mechanism assembly by turning it as

shown in Fig.10.

Remove the three screws Eand the one screw F

on the underside of the cassette mechanism

assembly.

Removing the reel base assembly

(See Fig.5 and 6)

Prior to performing the following procedure, remove

the cassette hanger / cassette holder.

From the upper side of the cassette mechanism

assembly, remove the C washer from each shaft of

the flywheel (BF) and (BR).

Turn over the cassette mechanism assembly and

remove the main belt. Pull out the flywheel (BF) and

(BR) downward respectively.

Removing the Flywheel (BF) and (BR)

assembly (See Fig.4 and 5)

The reel base assembly is not

repairable. Handle with care.

ATTENTION:

Selector link (B).

Inside of the reel base assembly

Reel disc assembly

Flywheel (BF)

Flywheel (BR)

Main-belt

Reel base assembly

Sub-belt

Motor assembly

Motor pulley

Soldering j

Fig.4

Fig.5

Fig.6Fig.7

C washer

Pinch-roller (R) assembly

Turn the selector link (B).

Andere Handbücher für KS-F363R

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere JVC Autoempfänger Handbücher

JVC

JVC KD-APD38 Bedienungsanleitung

JVC

JVC KD-R528 Leitfaden

JVC

JVC KD-G431 Bedienungsanleitung

JVC

JVC KD-SH1000J Bedienungsanleitung

JVC

JVC GET0642-001A Bedienungsanleitung

JVC

JVC KD-S32 Leitfaden

JVC

JVC KD-AVX77 - EXAD - DVD Player Bedienungsanleitung

JVC

JVC CDA-5755 Bedienungsanleitung

JVC

JVC KD-DV6107 Bedienungsanleitung

JVC

JVC KD-G521 Bedienungsanleitung

JVC

JVC KD-S5050 - In-Dash CD Player Bedienungsanleitung

JVC

JVC KD-BT11 - Radio / CD Bedienungsanleitung

JVC

JVC KD-DV4402 Bedienungsanleitung

JVC

JVC KD-APD38 Bedienungsanleitung

JVC

JVC KW-R400 Bedienungsanleitung

JVC

JVC KD-S34 Bedienungsanleitung

JVC

JVC KS-FX945R Bedienungsanleitung

JVC

JVC KD-SX947R Bedienungsanleitung

JVC

JVC KD-R400J Bedienungsanleitung

JVC

JVC KD-T812BT Bedienungsanleitung

JVC

JVC SX50M - KD Radio / CD Player Bedienungsanleitung

JVC

JVC KW-XC410 - Radio / CD Bedienungsanleitung

JVC

JVC KD-LH2000 Bedienungsanleitung

JVC

JVC KS-FX222 Bauanleitung

Beliebte Autoempfänger Handbücher anderer Marken

Motorola

Motorola VWA63 Bedienungsanleitung

Nextar

Nextar D3201 Bedienungsanleitung

Alpine

Alpine CDE-163BT Bedienungsanleitung

Pioneer

Pioneer DEH-P645R Bedienungsanleitung

Axxera

Axxera XDMA7600 Betriebsanleitung

XM OnyX Bedienungsanleitung

Sound Storm

Sound Storm STM93R Bedienungsanleitung

Soundstream

Soundstream VIR-5000 Bedienungsanleitung

Avson

Avson MKT Platform Bedienungsanleitung

Sony

Sony MEX-1HD - Audio Library System Bedienungsanleitung

Pioneer

Pioneer DVH-P500UB Bedienungsanleitung

Blaupunkt

Blaupunkt SANTIAGO CR 87 Bedienungsanleitung

Sony

Sony CDX-4160 - Cd Receiver Bedienungsanleitung

XFIRE AUDIO

XFIRE AUDIO BMW42S Bedienungsanleitung

VDO

VDO CD 2253 Bedienungsanleitung

Volvo

Volvo 13 84 580 Bedienungsanleitung

ZENEC

ZENEC ZE-160DVD Bedienungsanleitung

Medion

Medion Car Audio Bedienungsanleitung