Kaba 7102 series Bedienungsanleitung

7 1 0 2

7 1 0 8

SERIES

Installation Instructions

Important: Please keep these instructions. The combination of this lock has

been factory preset: 2 and 4 pressed together, then 3.

WARNING

For your own safety, you must change the combination at the time of

installation.

PLEASE READ AND FOLLOW ALL DIRECTIONS CAREFULLY

Since every installation is unique, carefully check windows, frame, door, etc. to

ensure that the recommended procedures will not cause damage. ABA is not

responsible for any damage caused by installation.

Tools Required

•1⁄4" (6 mm) Drill Bit

• 1" (25 mm) Wood Chisel

•3⁄4" (19 mm) Hole Saw

• Phillips-head Screwdriver

• 1" (25 mm) Drill Bit or Hole Saw

• 15⁄8" (41 mm) Hole Saw

Caution: Wear safety glasses when preparing door.

• 2 Pairs of Pliers

• Hacksaw

• Hammer

• Center Punch

• Drill (variable speed recommended)

For technical assistance please call

1-800-849-TECH (8324) or 336-725-1331

Table of Contents

Checklist .................................................................2

DeterminingtheHandofYourDoor .........................................2

A. DeterminingtheLockLocation .............................................3

B. MarkingtheDoor..........................................................3

C. DrillingHolesintheDoor ..................................................4

D. MakingtheBoltFacePlateCutout ..........................................4

E. InstallingtheBolt .........................................................5

F. AdjustingtheLock ........................................................5

G. InstallingtheLock.........................................................6

H. CheckingtheLocksOperation ..............................................7

I. InstallingtheStrike........................................................8

J. SettingaNewCombination.................................................8

. Instructions for Resetting Unknown Combinations . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

L. Troubleshooting ..........................................................12

Templates (Center of Manual)

CHECKLIST

Use this checklist to make sure that

everything has been included. 

A - Front Lock

C - Dead Bolt 7102 (2 3⁄4") or

7108 (2 3⁄8") (model specific)

D - Inside Thumbturn Assembly

E - Inside Combination Change Assembly

Screw Pack:

F - Strike Plate

G - 4 thru-bolts (3")

H - 2 (bolt) combination wood/metal screws

I - 4 combination wood/metal screws

J - 4 Thru bolts (2 3⁄8")

- 4 Thru bolts (2")

Templates (in center of booklet)

DETER INE THE HAND OF YOUR DOOR

Many of the installation instructions refer to the handing of your door. The hand

of the door is determined with the door in the closed position, from the exterior

or pushbutton side of the door.

A) Right Hand Door. Door opens inward

(push). Hinged on the right side.

B) Left Hand Door. Door opens inward

(push). Hinged on the left side.

C) Right Hand Reverse Door. Door opens

outward (pull). Hinged on the right side.

D) Left Hand Reverse Door. Door opens out-

ward (pull). Hinged on the left side.

LH - Left Hand

RH - Right Hand

LHR - Left Hand Reverse

RHR - Right Hand Reverse



A. DETER INING THE LOCK

LOCATION

Install the lock with the exterior thumbturn hole at

least 7" (18 cm) above your primary lockset so it is

comfortable to operate and not in the way when

you turn the door knob.

A minimum stile width of 4" (10.16 cm) is recom-

mended for mounting (See Figure 1-1).

B. ARKING THE DOOR

NOTE: Be sure to use the correct template

(right-hand or left-hand door - 2 3⁄8" or 2 3⁄4").

If the wrong template is used, you will have to

redrill the door, leaving previously drilled holes

exposed.

B-1 Carefully fold the template on 2 3⁄8" or 2 3⁄4"

line (found in the center of this booklet)

(See Figure 2-1).

B-2 Tape the template securely to the outside of the

door so that all the indicated folds are properly aligned with the edge of the

door.

B-3 Use a center punch to make the marks for drilling the seven holes precisely

at the points indicated on the template. The center punch mark in the edge

of the door must be centered based on the thickness of the door.

B-4 Remove the template.

C. DRILLING HOLES IN THE DOOR

CAUTION: Positioning and drilling must be done

straight to ensure trouble free operation of the 7100

Series lockset. Improper drilling may result in exces-

sive force being exerted on the lock which may result

in the premature wearing of its mechanical parts.

You must do C-1 first otherwise it will be

impossible to drill the 1⁄4" (6 mm) holes.

C-1 Use a 1⁄4" (6 mm) drill bit to drill the four holes

marked A (See Figure 3-1). Begin drilling at a

slow speed and increase the speed gradually

until the tip of the drill bit emerges from the other side of the door. Repeat

this procedure from the opposite side of the door. This technique will pre-

vent splintering of the door or breaking the drill bit.

2-1

1-1

(18 cm)

(102 mm)

3-1

1⁄4"A

1" D

3⁄4"C

C-2 Use a hole saw with pilot bit to make the 1 5⁄8"

(41 mm) hole (B). Apply pressure evenly until

the circular blade cuts the first side of the door

and the tip of the pilot bit emerges through the

other side, then stop. Drill from the other side

until the 1 5⁄8" (41 mm) hole is completed.

C-3 Repeat C-2 for the 3⁄4" (19 mm) hole, (C).

C-4 The final 1" (25 mm) hole (D) is crossbored

through the edge of the door. Carefully bore 4"

(10 cm) deep (See Figures 3-1 and 3-2).

D. AKING THE BOLT FACE PLATE

CUTOUT

This procedure is applicable to wood doors.

D-1 Insert the bolt into the 1" (25 mm) hole until the face plate butts up against

the door edge. Draw a line around the face plate. Remove the bolt from the

door, A (See Figure 4-1).

D-2 For doors without a beveled edge, use a sharp

1" (25 mm) wood chisel to remove approxi-

mately 1⁄8" (3 mm) of material or enough so

the face plate is perfectly flush with the edge

of the door, B (See Figure 4-1).

D-3 For doors with a beveled edge, follow step 2

except the face plate will not be flush with the

edge of the door, but rather square to the face of the door. In order to

accomplish this, you must remove more wood from the higher edge of the

door.

E. INSTALLING THE BOLT

E-1 Right Hand Door (see template)

a. Insert the bolt, with the arrow pointing up,

into the 1" (25 mm) hole (See Figure 5-1).

b. Secure the bolt face plate to the door with

the two Phillips-head screws provided.

3-2

5-1

4-1

4" (10 cm)

3-1

1⁄4"A

1" D

3⁄4"C

E-2 Left Hand Door (see template)

a. Insert the bolt, with the arrow pointing down,

into the 1" (25 mm) hole (See Figure 5-2).

b. Secure the bolt face plate to the door with

the two Phillips-head screws provided.

F. ADJUSTING THE LOCK

The lock has been pre-assembled to

accommodate doors up to 2 1⁄4" (57 mm) thick.

If your door is 1 3⁄8" to 2 " (35 mm to 51 mm) thick,

you must shorten both tailpieces X and Y (See

Figure 6-1).

F-1. Shorten the combination change tailpiece X

according to your door thickness. Tailpiece X

has been premarked for various door thick-

nesses for accuracy and convenience (See

Figure 6-1).

a. After determining the breakoff point, hold

the tailpiece firmly with a pair of pliers on

the lock side of the tailpiece, just beside

the desired break line (See Figure 6-2).

b. With a second pair of pliers, grip the

tailpiece at the other side of the line

and bend it up and down until it breaks

(See Figure 6-2).

F-2. While holding the lockset firmly against the outside surface of the door,

(See Figure 6-1), mark tailpiece Yat the point where it extends

1⁄2" - 5⁄8" beyond the interior surface of the door.

a. After determining the breakoff point, hold the tailpiece firmly with a pair

of pliers on the lock side of the tailpiece, just beside the desired break

line (See Figure 6-2).

b. With a second pair of pliers, grip the tailpiece at the other side of the

line and bend it up and down until it breaks (See Figure 6-2).

5-2

6-2

6-1

G. INSTALLING THE LOCK

• For 1 3⁄8" - 1 1⁄2" (35 mm - 38 mm) thick doors, use the 2 3⁄8" (44 mm) thru bolts.

• For 1 1⁄2" - 2" (38 mm - 51 mm) thick doors, use the 2 3⁄8" (44 mm) thru bolts.

• For 2" - 2 1⁄4" (51 mm - 57 mm) thick doors, use the 3" (76 mm) thru bolts.

G-1. With the bolt extended in the locked position,

mount the lock from the outside of the door.

Insert the tailpiece Yinto the vertical cutout of

the bolt assembly and the tailpiece Xinto the

3⁄4” (19 mm) hole (See Figure 7-1).

G-2. Hold the exterior lock assembly firmly against

the door. Try the factory-set combination.

Press buttons #2 and #4 together, release,

press button #3, and release. A distinctive

click must be felt to indicate that the button

has been correctly depressed. Turn the out-

side thumbturn to the right (clockwise) to the

stop position and release (the bolt should be

fully retracted). If not, turn the thumbturn to

the left (counterclockwise) to the stop posi-

tion and repeat Step G-2.

G-3 While holding the lock firmly against the out-

side surface of the door with one hand, use

the other to mount the inside thumbturn

assembly to the interior side of the door with

two thru-bolts finger tight (See Figure 7-2).

Make sure that tailpiece Yis engaged into the

vertical cutout of the inside thumbturn assembly.

G-4 Insert tailpiece Xinto the horizontal slot of the

combination change assembly. It may be nec-

essary to use a screwdriver to align tailpiece X

with the combination change assembly (See

Figure 7-3). Once aligned, secure with two

thru-bolts, but do not tighten (See Figure 7-4).

Note: The inside thumbturn is shown in a vertical position to show the two

thru-bolts. It may be assembled either vertically or horizontally.

I PORTANT: Tailpiece Xmust be inserted in the horizontal slot in order to

change your combination.

G-5 Make sure that both assemblies are correctly centered over the holes.

Tighten the thru-bolts evenly. Uneven tension could cause a malfunction

or damage to the lock.

7-1

7-4

7-3

7-2

H. CHECKING THE LOCK’S OPERATION

I PORTANT: The following steps MUST be performed while the DOOR IS OPEN.

Note: Turning the outside thumbturn to the left (counterclockwise) to the stop

position and releasing extends the bolt to the locked position. To retract the

bolt from the outside, depress the buttons of your preset combination, then

turn the thumbturn to the right (clockwise) to the stop position.

H-1 Turn the outside thumbturn to the left (coun-

terclockwise) until it stops, then release it (See

Figure 8-1).

H-2 Press the preset factory combination (2 and 4

pressed together, release, then 3, and release)

(See Figure 8-2). A distinctive click must be

felt to indicate that the buttons have been cor-

rectly depressed.

H-3 Turn the outside thumbturn to the right (clock-

wise) until it stops; the bolt should fully retract

(See Figure 8-3). If the bolt does not retract,

turn the thumbturn to the left (counterclock-

wise) until it stops. This will clear previously

depressed buttons. Release it and repeat Steps

H-2 and H-3.

H-4 Release the outside thumbturn; the bolt will

stay in the retracted position.

H-5 Turn the inside thumbturn Ato the stop posi-

tion; the bolt will extend to its locked position

(See Figure 8-4).

H-6 If the bolt does not retract or extend fully,

loosen the two thru-bolts of the inside thumb-

turn assembly A (See Figure 8-4). Move the

inside thumbturn assembly upward or down-

ward to properly center the inside thumbturn

assembly with the tailpiece, then tighten the

thru-bolts, and repeat Steps H-1 to H-5.

H-7 If the bolt still does not fully retract or extend

after repeating Step H-6, loosen the two thru-

bolts of the inside thumbturn assembly Aand combination change

assembly B (See Figure 8-4). Move the lock upward or downward to

properly align both tailpieces of the inside thumbturn assembly and

combination change assembly. Tighten the four thru-bolts and repeat

Steps H-1 to H-5 to ensure proper operation.

8-1

8-2

8-3

8-4

KABA SI PLEX®

LI ITED WARRANTY

aba Access Control warrants this product to be free from defects in material

and workmanship under normal use and service for a period of one (1) year.

aba Access Control will repair or replace, at our discretion, locks found by

aba Access Control analysis to be defective during this period. Our only liabil-

ity, whether in tort or in contract, under this warranty is to repair or replace

products that are returned to aba Access Control within the one (1) year war-

ranty period.

This warranty is in lieu of and not in addition to any other warranty or condi-

tion, express or implied, including without limitation merchantability, fitness for

purpose or absence of latent defects.

ATTENTION: This warranty does not cover problems arising out of improper

installation, neglect or misuse. All warranties implied or written will be null and

void if the lock is not installed properly and /or if any supplied component part

is substituted with a foreign part. If the lock is used with a wall bumper, the

warranty is null and void. If a doorstop is required, we recommend the use of a

floor secured stop.

The environment and conditions of use determine the life of finishes

on aba Access Control products. Finishes on aba Access Control products

are subject to change due to wear and environmental corrosion. aba Access

Control cannot be held responsible for the deterioration of finishes.

Authorization to Return Goods

Returned merchandise will not be accepted without prior approval. Approvals

and Returned Goods Authorization Numbers (RGA Numbers) are available

through our Customer Service department in Winston-Salem, NC

(800) 849-8324. The serial number of a lock is required to obtain this RGA

Number. The issuance of an RGA does not imply that a credit or replacement

will be issued.

The RGA number must be included on the address label when material

is returned to the factory. All component parts including latches and strikes

(even if not inoperative) must be included in the package with return. All

merchandise must be returned prepaid and properly packaged to the address

indicated.

Andere Handbücher für 7102 series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Kaba Türschloss Handbücher

Kaba

Kaba 7002 Series Bedienungsanleitung

Kaba

Kaba C-lever Bedienungsanleitung

Kaba

Kaba c-lever 2662-K5 Bedienungsanleitung

Kaba

Kaba E-PLEX 5X51 Bedienungsanleitung

Kaba

Kaba Confidant RFID Kit 2 Bedienungsanleitung

Kaba

Kaba PowerLever 1550 Bedienungsanleitung

Kaba

Kaba Simplex LP1000 Series Bedienungsanleitung

Kaba

Kaba Ilco 790/79 Series Bedienungsanleitung

Kaba

Kaba Solitaire 710-II Series Bedienungsanleitung

Kaba

Kaba SIMPLEX 3000 NARROW STILE Bedienungsanleitung

Kaba

Kaba E30 Bedienungsanleitung

Kaba

Kaba SIMPLEX 900 Series Bedienungsanleitung

Kaba

Kaba Saflok RT Series Bedienungsanleitung

Kaba

Kaba E-Flash EF780 Bedienungsanleitung

Kaba

Kaba E-PLEX STANDARD Series Bedienungsanleitung

Kaba

Kaba PowerLever 15 Series Bedienungsanleitung

Kaba

Kaba Solitaire 710-II Series Bedienungsanleitung

Kaba

Kaba E-Plex 5x00 Cylindrical Bedienungsanleitung

Kaba

Kaba E-PLEX Bedienungsanleitung

Kaba

Kaba E-Flash 680 Bedienungsanleitung

Kaba

Kaba Saflok MT RFID Bedienungsanleitung

Kaba

Kaba C-lever Bedienungsanleitung

Kaba

Kaba c-lever acc. EN1906 Cl.1 Bedienungsanleitung

Kaba

Kaba Simplex 1000 Series Bedienungsanleitung

Beliebte Türschloss Handbücher anderer Marken

Assa Abloy

Assa Abloy effeff 827A-IP Bedienungsanleitung

We.lock

We.lock SECBNEBL51 Bedienungsanleitung

Iseo

Iseo MA1A Bedienungsanleitung

ID Lock

ID Lock 150 Bedienungsanleitung

Lockly

Lockly ACCESS TOUCH PRO Bedienungsanleitung

iLoq

iLoq G50S Bedienungsanleitung

SDC

SDC Z7835 Bedienungsanleitung

ilco

ilco 452 Bedienungsanleitung

Samsung

Samsung shs-h705 Bedienungsanleitung

TRU-BOLT

TRU-BOLT 08102017 Bedienungsanleitung

CDVI

CDVI 500-LADJ Bedienungsanleitung

Igloohome

Igloohome Deadbolt 2S Metal Grey Montage- und Wartungsanleitung

eSSL

eSSL FL-300 Bedienungsanleitung

JAKO

JAKO JKBTNX4 Bedienungsanleitung

Dorma

Dorma MUNDUS PREMIUM GK 50 Benutzerhandbuch

SCOOP

SCOOP Pullbloc 4.1 FS Panik Bedienungsanleitung

Yale

Yale MORTISE 8800 SERIES Bedienungsanleitung

Siegenia

Siegenia KFV AS3500 Bedienungsanleitung