Kaba SIMPLEX 3000 NARROW STILE Bedienungsanleitung

Installation Instructions

SIMPLEX®3000 NARROW STILE

TABLE OF CO TE TS

Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Tools Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

A. Combination Lock Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

B. Mounting Lock to Stile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

C. Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

D. Combination Change Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

E. Resetting an Unknown Combination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Warnings and Cautions

Important: Carefully inspect windows, doorframe, door, etc. to ensure that

the recommended procedures will not cause any damage. Kaba Access

Control’s warranty does not cover damages caused by installation.

Caution: Wear safety glasses when preparing door.

• Combination lock assembly

• Instructions for changing

combination

• Operating instructions

• Warranty card

• DF-59 keys

• Mounting screws 10-24 thd. X 2 1⁄8"

• Inside trim plate assembly

• Cylinder groove screws #4

self-tapping screw

• Optional cylinder guard (3002

models only)

• Cam stop screw 6–32 thd. X 3⁄16"

long

PACKAGE CO TE TS

TOOLS REQUIRED FOR I STALLATIO :

• Flat blade screwdrivers (small and medium)

• Phillips head screwdriver (large)

• Tape

• Hammer

• Deburring tool

• Drill (variable speed recommended)

• Center punch

• (3⁄32") drill bit

• (3⁄8") drill bit

• (1⁄8") drill bit

• (1⁄4") drill bit

• (7⁄8") hole saw

A. COMBI ATIO LOCK ASSEMBLY

A-1 Cylinder Installation: Remove interposer

assembly (A) by removing one round head

screw and one flat head screw (See Figure 1-1).

A-2 Install Mortise cylinder by turning

cylinder until cylinder cam (E)

contacts lock-in plate (B) (See

Figure 1-1). Turn cylinder to the

left (counterclockwise) less than

one turn until the key is positioned

in pull position (See Figure 1-2), also aligning

to cylinder set screw grooves (See Figure 1-1).

A-3 Assemble two cylinder positioning screws (C).

Make sure the heads of these screws are below

the underside of the cylinder cam (See Figure

1-1).

A-4 Reassemble the interposer assembly (A).

Interposer arm should be positioned central to

the cylinder cam (See Figure 1-3).

A-5 Assemble cam stop screw (D).

ote: Interposer stud to be centered before

mounting combination lock assembly

(See Figure 1-1).

Detent Position

of Interposer

Mortise

Cylinder

Code Plate and

Stud Assembly

Combination

Change Sleeve

Interposer

Stud

Cylinder in

“Pull” Position

Figure 1-3

Figure 1-2

Figure 1-1

Interposer

Arm

Cylinder

Cam

Partial Rear View

of arrow Stile Lock

Assembly

Side View

B. MOU TI G LOCK TO STILE

B-1 Place combination lock assembly over lock-in studs and slide downward

until a stop position is attained (approximately 1⁄8" of movement) (See

Figure 2-1). The top of the lock housing and drive assembly should be

flush when properly positioned.

ote: Before closing door, refer to operating instructions to check out the

operation of all lock functions.

Combination

Lock Assembly

As shown on Each

Drive Assembly

• 31⁄32" B.S. - L.H. Drive

• 31⁄32" B.S. - R.H. Drive

• 11⁄8" B.S. - L.H. Drive

• 11⁄8" B.S. - R.H. Drive

Housing Locator Stud

Drive Assembly

(Sample Illustration)

Latch Direction Will

Vary Based on Swing of

Door (Illustration Shows

Outswing Door)

Lock-In Studs

Figure 2-1

B-2 Fix two each 10-24 x 2 1⁄8" long round head machine screws (A) as shown

(See Figures 2-1 & 2-2). Using the DF-59 key, thread the control lock

assembly (B) into the combination change sleeve (C) DF-59 (See Figure

2-2) until trim plate is snug against stile. The key can only be removed in

vertical position.

arrow Stile Combination

Lock Side

arrow Stile

Trim Plate Side Combination Lock

Assembly Side View

Drive Assembly

Threaded Sex Bolts

arrow Stile Door Edge View

Trim Plate

Mounting Bushing

Mounting Screws

Figure 2-2

C. OPERATI G I STRUCTIO S

ote: All locks are shipped with the following combination:

#2 and #4 pushed at the same time, then #3. For proper security,

the factory set code must be changed at the time of installation.

C-1 Gaining Access By Combination Code

A. To clear any previously depressed code buttons, turn the thumb

turn to the left (counterclockwise) and release (See Figure 3-1).

B. Depress the code buttons in the proper order of your

combination. Release buttons after depressing.

C. Turn the thumb turn clockwise to the stop position. Observe the

latch being retracted to unlock the door (See Figure 3-2). The

lock will lock automatically when the thumb turn is released.

C-2 Gaining Access By Key Override

Insert cylinder key into cylinder on combination lock side of

door. Turn the key in clockwise direction (approximately 90°)

(See Figure 3-3). The latch should retract. Turn the key back to

key pull position and remove.

C-3 Locking Out Combination Code Access

A. Insert cylinder key into cylinder on combination lock side

of the door. Turn key in a counterclockwise direction to the

stop position (See Figure 3-4). Return the key to the pull

position and remove. The thumb turn should not turn while

the lock is in this mode.

B. To allow access again through a combination code, insert

key, turn clockwise approximately 45°. Return the key to

the pull position and remove (See Figure 3-5).

Figure 3-3

Figure 3-4

Figure 3-5

Figure 3-1

Figure 3-2

C-4 Latch Holdback

A. Insert cylinder key into cylinder on combination lock side of

the door. Turn the key in a clockwise direction to the stop

position, retracting the latch fully (See Figure 3-6). Hold the

key in that position and turn the thumb turn to the left

(counterclockwise). Bring the key to the pull position and

remove.

B. To allow the latch to return to lock mode, reinsert and turn

the key to the left (counterclockwise) to the stop position

(See Figure 3-7). Return the key to the pull position and

remove (See Figure 3-8).

Figure 3-6

Figure 3-7

Figure 3-8

Kaba Access Control warrants this product to be free from defects in

material and workmanship under normal use and service for a period of

one (1) year. Kaba Access Control will repair or replace, at our discre-

tion, Simplex Locks found by Kaba Access Control analysis to be defec-

tive during this period. Our only liability, whether in tort or in contract,

under this warranty is to repair or replace products that are returned to

Kaba Access Control within the one (1) year warranty period.

This warranty is in lieu of and not in addition to any other warranty or

condition, express or implied, including without limitation merchantabil-

ity, fitness for purpose or absence of latent defects.

ATTE TIO : This warranty does not cover problems arising out of

improper installation, neglect or misuse. All warranties implied or writ-

ten will be null and void if the lock is not installed properly and /or if

any supplied component part is substituted with a foreign part. If the

lock is used with a wall bumper, the warranty is null and void. If a

doorstop is required, we recommend the use of a floor secured stop.

The environment and conditions of use determine the life of finishes

on Kaba Access Control products. Finishes on Kaba Access Control

products are subject to change due to wear and environmental

corrosion. Kaba Access Control cannot be held responsible for the

deterioration of finishes.

Authorization to Return Goods

Returned merchandise will not be accepted without prior approval.

Approvals and Returned Goods Authorization umbers (RGA umbers)

for the Simplex 3000 Series are available through our Customer

Service department in Winston-Salem, C 800.849.8324 The serial

number of a lock is required to obtain this RGA umber. The

issuance of an RGA does not imply that a credit or replacement will be

issued.

The RGA number must be included on the address label when material

is returned to the factory. All component parts including latches and

strikes (even if not inoperative) must be included in the package with

return. All merchandise must be returned prepaid and properly pack-

aged to the address indicated.

KABA SIMPLEX®

LIMITED WARRA TY

KABA ACCESS CO TROL

2941 I DIA A AVE UE

WI STO -SALEM, C 27199-3770

O POSTAGE

ECESSARY

IF MAILED

I THE

U ITED STATES

BUSI ESS REPLY MAIL

FIRST-CLASS MAIL PERMIT O. 1563

POSTAGE WILL BE PAID BY ADDRESSEE

WI STO -SALEM, C

Thank you for purchasing our product. In order to

protect your investment and to enable us to better

serve you in the future, please fill out this registration

card and return it to Kaba Access Control, or

This lock will be used in what type of facility?

oCommercial Building oIndustrial/Manufacturing oAirport

oCollege/University oGovernment/Military oSchool/Educational

oHospital/Healthcare oOther (please specify)

What area is being secured with this lock? (e.g. Front Door, Common Door, Exercise Room)

This lock is:

oew Installation

oReplacing a conventional keyed lock

oReplacing a Kaba Mechanical Pushbutton Lock

oReplacing a Kaba Electronic Access Control

oReplacing a Keyless Lock other than Kaba

How did you learn about Kaba Access Control Pushbutton Locks?

oAdvertisement o Previous Use oInternet/Web oAnother Use

oLocksmith oMaintenance oTraining Class oOther (please specify)

What was your reason for buying this lock?

Who installed your lock?

oLocksmith oMaintenance oOther

oCheck here if you would like more information on Kaba Access Control locks.

ame

Position

Company

Address

City

State ZIP (Postal Code) Country

Phone

ame of Dealer Purchased From

Date of Purchase

Lock Model umber

REGISTRATIO CARD

Inhaltsverzeichnis

Andere Kaba Türschloss Handbücher

Kaba

Kaba 5 00 Series Bedienungsanleitung

Kaba

Kaba 7102 series Bedienungsanleitung

Kaba

Kaba EF 680E Bedienungsanleitung

Kaba

Kaba E-PLEX 5x70 Series Bedienungsanleitung

Kaba

Kaba S-module Bedienungsanleitung

Kaba

Kaba E-Plex 5900 Bedienungsanleitung

Kaba

Kaba E-Plex 5x00 Cylindrical Bedienungsanleitung

Kaba

Kaba E-PLEX 2000 Bedienungsanleitung

Kaba

Kaba E-Flash 680 Bedienungsanleitung

Kaba

Kaba Peaks Preferred Bedienungsanleitung

Kaba

Kaba Simplex LP1000 Series Bedienungsanleitung

Kaba

Kaba E-Plex 5200 Bedienungsanleitung

Kaba

Kaba Confidant RFID Kit 2 Bedienungsanleitung

Kaba

Kaba C-lever compact Bedienungsanleitung

Kaba

Kaba E-PLEX 50XX SERIES Bedienungsanleitung

Kaba

Kaba E-PLEX 3x65 Deadlatch/Exit Mortise Bedienungsanleitung

Kaba

Kaba C-lever Bedienungsanleitung

Kaba

Kaba E-PLEX STANDARD Series Bedienungsanleitung

Kaba

Kaba C-lever compact Bedienungsanleitung

Kaba

Kaba E-PLEX Bedienungsanleitung

Kaba

Kaba Ilco 790 Series Montageanleitung

Kaba

Kaba LCLX Bedienungsanleitung

Kaba

Kaba E-PLEX 2000 Bedienungsanleitung

Kaba

Kaba Solitaire 710-II Series Bedienungsanleitung

Beliebte Türschloss Handbücher anderer Marken

Assa Abloy

Assa Abloy effeff 827A-IP Bedienungsanleitung

Iseo

Iseo MA1A Bedienungsanleitung

ID Lock

ID Lock 150 Bedienungsanleitung

Lockly

Lockly ACCESS TOUCH PRO Bedienungsanleitung

iLoq

iLoq G50S Bedienungsanleitung

SDC

SDC Z7835 Bedienungsanleitung

ilco

ilco 452 Bedienungsanleitung

Samsung

Samsung shs-h705 Bedienungsanleitung

TRU-BOLT

TRU-BOLT 08102017 Bedienungsanleitung

CDVI

CDVI 500-LADJ Bedienungsanleitung

Igloohome

Igloohome Deadbolt 2S Metal Grey Montage- und Wartungsanleitung

eSSL

eSSL FL-300 Bedienungsanleitung

Dorma

Dorma MUNDUS PREMIUM GK 50 Benutzerhandbuch

SCOOP

SCOOP Pullbloc 4.1 FS Panik Bedienungsanleitung

Yale

Yale MORTISE 8800 SERIES Bedienungsanleitung

Siegenia

Siegenia KFV AS3500 Bedienungsanleitung

Saflok

Saflok Quantum ädesē RFID Bedienungsanleitung

ArrowVision

ArrowVision Shepherd 210 Bedienungsanleitung