Kaba SIMPLEX LD470 Bedienungsanleitung

Pushbutton Lock Installation Instructions

LD470

TABLE F C NTENTS

Checklist .....................................................................3

OperationalNote ..............................................................3

DeterminingtheHandofYourDoor..............................................4

A. ChangingtheDoorHanding.................................................4

B. Marking the Template and Drilling the Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

C. Installingthe atch ........................................................5

D. InstallingtheSpindle .......................................................6

E. Installingthe ock .........................................................6

F. InstallingtheStrikePlate ...................................................7

G. ChangingtheCode ........................................................8

H. UsingthePassageFunction .................................................9

I. RemovingthePassageFunction .............................................9

J. TroubleShooting..........................................................10

Warnings and Cautions

Important: Carefully inspect windows, doorframe, door, lights, etc.

to ensure that the recommended procedures will not cause damage. Kaba

Access Control’s warranty does not cover damages caused by installation.

Caution: Wear safety glasses when preparing door.

CHECKLIST

Use this checklist to make sure that

everything has been included. 

A—Outside unit

B—Inside unit

C—Gaskets (2)

D—Universal trim plate (2)

E—Spindles (3 lengths)

F— atch

G—Strike plate

H— atch and strike screws (4)

J—Tweezers

K—Mounting screws (8) (4 lengths)

L—Spare tumblers – coded (2), uncoded (2)

M—Code card

N—Hex wrench



A B C D

PERATI NAL N TE:

Prior to beginning installation, please check that all parts are working

correctly. Press the “C” button 3-5 times. Enter the code from the factory

supplied code card. Rotate the outside lever down and release. The lever

should return easily under spring pressure. If you intend to change the code,

you should do it before installing the lock (See Code Change Instructions).

Make sure that the inside lever moves freely.

Check that the latch bolt moves freely by pressing the bolthead at the end,

and also by turning the flat spindle in the latch cam.

For technical assistance please call

1-800-849-TECH (8324) or 336-725-1331

DETERMINING THE HAND F Y UR D R

Many of the installation instructions refer to

the handing of your door. The hand of the door

is determined with the door in the closed position,

from the exterior or pushbutton side of the door.

A) Right Hand Door. Door opens inward

(push). Hinged on the right side.

B) eft Hand Door. Door opens inward

(push). Hinged on the left side.

C) Right Hand Reverse Door. Door opens

outward (pull). Hinged on the right side.

D) eft Hand Reverse Door. Door opens

outward (pull). Hinged on the left side.

A. CHANGING THE D R HANDING

A-1 For the outside unit assembly, remove the rubber plug from the outside

lever, exposing the lever set screw.

A-2 Using the hex wrench supplied, remove the

set screw from the lever in question.

A-3 Remove the lever and rotate it 180º. Slide the

lever back onto the lock.

A-4 Using the hex wrench supplied, reinstall the

set screw. Assure the lever rotates freely.

A-5 Reinstall the rubber plug, which was removed earlier.

A-6 For the inside unit assembly, turn the unit over

so the back side is facing up.

A-7 Remove the 4 screws securing the cover plate

to the assembly. Then lift the cover plate and

set aside.

A-8 ift the stop plate ring and position it accord-

ing to the pictures to the right for this application.

A-9 Resecure the cover plate using the 4 screws

removed earlier.

A-10 Remove the rubber plug from the inside lever,

exposing the lever set screw.

H - eft Hand

RH - Right Hand

HR - eft Hand Reverse

RHR - Right Hand Reverse

All units are factory handed for right

hand doors.

A-11 Using the hex wrench supplied, remove the set screw from the lever in

question.

A-12 Remove the lever and rotate it 180º. Slide the lever back onto the lock.

A-13 Using the hex wrench supplied, reinstall the set screw. Assure the lever

rotates freely.

A-14 Reinstall the rubber plug, which was removed earlier.

B. MARKING THE TEMPLATE AND DRILLING THE D R

B-1 Find and remove the template from the installation manual. Carefully fold

along the dotted line that matches the backset the application requires.

B-2 From the exterior (or push button side) of the

door, place the dotted line of the template

along the edge of the door.

B-3 Carefully mark the 3 holes on the template

(2 mounting holes and 1 spindle hole.

B-4 Drill the 3 holes, making sure to drill

them straight.

C. INSTALLING THE LATCH

C-1 Using the center line of the latch (marked on template), mark the point

where the cross bore for the latch should be drilled.

C-2 Drill a 1" (25 mm) diameter hole, 3 3⁄4" (96mm) deep, on that center point

of the edge of the door.

C-3 Insert the latch into the hole and outline the face of the latch (already

prepped on most metal doors).

C-4 Remove the latch.

C-5 Using a chisel, remove the material 1⁄8" (3 mm) deep from the door for

the faceplate of the latch (already prepped on most metal doors).

C-6 Reinsert the latch and install the latch using the mounting screws provided.

D. INSTALLING THE SPINDLE

D-1 For doors ranging in thickness from 1 3⁄8"

(35 mm) to 1 7⁄8" (48 mm) use the shorter

spindle (supplied) and align as shown.

D-2 For doors ranging in thickness from 2"

(51 mm) to 2 1⁄2” (64 mm) use the longest

spindle (supplied) and align as shown.

D-3 Make sure the spindle matches the picture

shown depending on the hand of the lock.

E. INSTALLING THE L CK

E-1 Place the rubber gaskets around the lock

body with the lock body sitting into the

recessed portion of the gasket. Assure

the holes in the back of the lock and the

gasket match.

E-2 If using the cover plates (supplied), an

additional hole must be drilled in the cover

plates before the installation continues

(See back of cover plate).

E-3 Once additional hole has been drilled, place the cover plate on the back of

the lock between the gasket and the door.

E-4 For doors ranging in thickness from 1 3⁄8”( 35 mm) to 1 5⁄8”( 41 mm), use

the shorter mounting screws (supplied) and align as shown

E-5 For doors ranging in thickness from 1 3⁄4" (44 mm) to 2” (51 mm), use the

medium mounting screws (supplied) and align as shown.

E-6 For doors ranging in thickness from 2 1⁄8" (54 mm) to 2 1⁄2” (64 mm), use

the longest mounting screws (supplied) and align as shown.

Note: If cover plates are used, it may be necessary to use the next size

screw to mount the lock.

E-7 Hold the outside and inside units on the door with the spindle in the

proper position.

E-8 Finger-tighten the (2) mounting screws, assuring the lock is vertical and

sitting flush against the door.

Viewed from

the outside

Door hung on right

spindle should

engage the latch

as above

Door hung on left

spindle should

engage the latch

as above

Note: Assurance that the proper spindle is

used is extremely critical. If the wrong

spindle is used, binding or lockout can occur.

The door thickness including gaskets and trim plates can not exceed 2 1⁄2"

(64 mm).

E-9 Before final tightening, make sure the code works and all features on the

unit work as intended.

Note: Do not close the door until the lock has been tested and you are

confident it works properly.

E-10 Tighten the mounting screws firmly, being careful not to over tighten the

screws, as this may cause the lock to function poorly or not at all.

F. INSTALLING THE STRIKE PLATE

F-1 Push the door nearly shut to locate the center line of the latch bolt. Mark

the center line on the door frame.

F-2 Using the strike, align the center of the strike opening with the center just

marked.

Make sure to account for any weather stripping or door stop if necessary.

F-3 Carefully trace the outside profile of the strike. Also trace the latch hole in

the strike.

F-4 Using a chisel, carefully remove approximately 1⁄16”

(1 mm) deep worth of material from the traced area

(already prepped on most metal doors). The latch face

plate should sit flush with the edge of the door.

F-5 Drill or cut a recess in the door frame for the latch bolt

in the center of the strike latch hole, traced earlier.

F-6 Place the strike into the newly chiseled area, making sure it sits flush and

there are no obstructions in the latch hole of the strike (remove any

obstructions or debris).

F-7 Install the strike plate with 2 screws provided.

“deadlatch”

“latchbolt”

N TE: The dead-latch must not fall into

the latch hole. The dead-latch protects

against manipulation of the latch bolt. If

the dead-latch is able to fall into the latch

hole, remove the strike and reposition it so

this condition does not happen.

G. CHANGING THE C DE

G-1 Remove the lock from the door.

G-2 Remove the 4 retaining (red) screws from

the back of the outside unit assembly. Take

extra care to keep the outside unit assembly on a flat surface when you

are removing the cover plate because there are many small components

inside.

G-3 You will now see that there are 5 red color coded tumblers and 8 blue col-

ored un-coded tumblers, plus 1 clear tumbler (‘C’ button).

G-4 To change your code, hold the outside unit assembly with the push-buttons

facing down. Press the “C” button and

hold it.

G-5 Using the tweezers supplied (or small

needle nose pliers), you can easily

remove one or more of the coded and

un-coded tumblers.

G-6 Please note the different shapes of the

tumblers before reinserting them into

the lock body. There is a difference in

shape between the coded and un-coded

tumblers as illustrated. When refitting

the tumblers into the lock body, they must be fitted facing the correct way

as show in the illustration.

G-7 After you have refitted the tumblers and made a note of the new code,

replace the metal cover plate with the 4 screws.

Square

cut out

push button

Square

cut out

Square

cut out

RED CODED

TUMB ER

B UE

UNCODED

TUMB ER

Square

cut out

“deadlatch”

“latchbolt”

If the “C” is not held in while changing

the code, the lock can be damaged.

Note: The red tumblers represent coded

digits and the blue tumblers

represent non-coded digits.

Note: NEVER remove the ‘C’ tumbler.

Note: All square cutouts must face outwards. The bump on the tumbler

(either color) must fall into the machined slot.

Note: With the spare tumblers provided, you can either increase the num-

ber of digits in your code to 6-7, or reduce to 3-4.

23/8” (60 mm)

TEMPLATE

TOP

23/4” (70 mm)

23/8” (60 mm)

23/4” (70 mm)

LD470 Series

⁄

8”(10 mm)

Hole

⁄

outside, fold along the left edge of the door

Outline of Lock Housing

Outline of

Gasket

⁄4” (70 mm) Backset ONLY. From outside, fo

⁄8” (60 mm) Backset ONLY. From outside, f

Center line of latch

TEMPLATE

11⁄8”(30 mm)

Hole

⁄

4” (159 mm) Hole

⁄4” (70 mm) Backset ONLY. From

⁄8” (60 mm) Backset ONLY. From

⁄8” (10 mm) Hole

Gasket

old along the right edge of the door

1” (25 mm)

7⁄8” (21.5 mm)

Inhaltsverzeichnis

Andere Kaba Sperren Handbücher

Kaba

Kaba ilco 760 Montageanleitung

Kaba

Kaba PowerPlex 2000 Series Bedienungsanleitung

Kaba

Kaba E-Plex 5x63 Bedienungsanleitung

Kaba

Kaba E-Flash EF680 Bedienungsanleitung

Kaba

Kaba C-lever compact Bedienungsanleitung

Kaba

Kaba 7006 Series Bedienungsanleitung

Kaba

Kaba Simplex 7104 Series Bedienungsanleitung

Kaba

Kaba E-Flash EF680 Bedienungsanleitung

Kaba

Kaba Simplex 7104 Series Bedienungsanleitung

Kaba

Kaba La Gard MECHANICAL Bedienungsanleitung

Kaba

Kaba E-PLEX 2000 Bedienungsanleitung

Kaba

Kaba Simplex 8100 Series Bedienungsanleitung

Kaba

Kaba E-Plex 5000 Bedienungsanleitung

Kaba

Kaba C-lever Bedienungsanleitung

Kaba

Kaba Generation E-760 AUTO DEADBOLT ASM Office Bedienungsanleitung

Kaba

Kaba E-Plex 5 Series Bedienungsanleitung

Kaba

Kaba 7004 Series Bedienungsanleitung

Kaba

Kaba EX3600 Bedienungsanleitung

Kaba

Kaba simplex 7106 series Bedienungsanleitung

Kaba

Kaba LA GARD 1947 Bedienungsanleitung

Kaba

Kaba Simplex 6200 Series Bedienungsanleitung

Kaba

Kaba Combi B 30 Bedienungsanleitung

Kaba

Kaba Simplex 1000 Series Installationsanleitung

Kaba

Kaba PowerPlex 2000 Series Bedienungsanleitung

Beliebte Sperren Handbücher anderer Marken

Magic

Magic 105 Bedienungsanleitung

Gantner

Gantner GAT NET.Lock 7020 System Kurzanleitung

Wittkopp

Wittkopp Insys 7202 Bedienungsanleitung

Dorma

Dorma Studio Classic Bedienungsanleitung

Securam

Securam ECSL-601 Bedienungsanleitung

Sudhaus

Sudhaus 3003 Bedienungsanleitung

Safety 1st

Safety 1st 48517 Bedienungsanleitung

Pado

Pado FDS-10 Bedienungsanleitung

Esco

Esco systeQ Series Bedienungsanleitung

COMPX

COMPX National D8951 Bedienungsanleitung

secureo

secureo Key Box Bedienungsanleitung

Stock Loks

Stock Loks C8713 Bedienungsanleitung

COMPX

COMPX 1T-058 Betriebsanleitung

Auslock

Auslock T11 Bedienungsanleitung

ELCOM

ELCOM 7205 Bedienungsanleitung

Stealth SAFES

Stealth SAFES ShadowVault Bedienungsanleitung

Knox

Knox KeySecure 5 Bedienungsanleitung

Kwikset

Kwikset 48334/01 Bedienungsanleitung