Kane 455 Bedienungsanleitung
KANE455
Quick Reference Guide
Infra-red emitter and torch light
Menu controls ~ Scroll up/down
Enter
Function buttons x 4
(See below for details)
Rotary switch
Particle filter
Water trap
“Battery charging” indicator
Analyser Connections Flue Gas Inlet
(see diagram overleaf) (see diagram overleaf)
ON / OFF
Turns the analyser ON / OFF
BACKLIGHT
Switches backlight & torch light
ON / OFF
PUMP
Turns the pump ON / OFF
Hold button to zero pressure
SEND / ENTER
Send readings to printer
(Press button for 1 second.)
Send readings to memory
(Hold button down for 2+ secs.)
Stock No. 18839-2 July 2014
© Kane International Ltd
Battery charger
connection
Flue Gas Inlet
Watertrap Drain
with Red Screw
Plug
Flue probe temperature (T1)
Inlet temperature (T2)
Pressure connection
P1
Pressure connection
P2 (differential)
Fit Spigot to Hose before
connecting to Analyser
1. BEFORE USING ANALYSER CHECK THE FOLLOWING:
Particle filter is not dirty inside
Water trap and flue probe hose are empty of water
Water trap and red screw plug are fitted correctly to the analyser
Flue probe hose is connected properly to the flue gas inlet
Flue probe temperature plug is connected into T1 temperature connection
Please read the Safety Warnings in the User Manual
2. FRESH AIR PURGE
Position the flue probe in fresh air, then press the “On/Off” button. The analyser auto-
calibrates for approximately 90 seconds. When complete…
Select “Ratio” on the dial. In fresh air the CO reading = 0ppm
Select “O2/Eff” on the dial. In fresh air the O2 reading = 20.9%
Select “Status” on the dial to view the following…
STATUS display
BAT 59
11 : 46 : 29
15 / 05 / 08
CAL 283
- Battery status. If less than 20 recharge or replace, (see section 10)
- Current time. Can be set via the “Menu”, (see section 11)
- Current date. Can be set via the “Menu”, (see section 11)
- Number of days until next check and calibration is required
Note: Boiler inlet air temperature can either be…
a) Set automatically by the flue probe during the fresh air purge
or b) Continuously measured if a thermocouple is plugged into the T2 socket
3. COMBUSTION TESTS
Select “Ratio” on the dial to check that the analyser is set for the correct fuel. To change
fuel select MENU / SETUP / SET FUEL then use scroll and enter, (see section 11).
Position the flue probe as per the boiler manufacturer’s instructions; typically the tip of
the flue probe is inserted to the centre of the flue. The readings will stabilise after 60
seconds assuming the boiler conditions are stable.
The rotary switch can be used to display the following information…
RATIO display
NAT GAS
R 0.0001
COP 12
CO2% 8.8
- Fuel type can be changed via “Menu”, (see section 11)
- CO/CO2 ratio
- Carbon Monoxide, (ppm)
- Carbon Dioxide, (%)
Press SEND to print a full combustion test. (Also sends to PC if Wireless module fitted).
Hold SEND for 2+ seconds to log a full combustion report.
O2/EFF display
O2% 5.4
TFC 55.1
TIC 17.2
EfC% 98.3
- Oxygen left after combustion. Should be 20.9% in fresh air.
- Flue temperature, (C)
- Inlet temperature. Normally set by flue probe during fresh air purge.
- Condensing boiler efficiency (EfC). Can be changed via “Menu”
Press SEND to print a full combustion test. (Also sends to PC if Wireless module fitted).
Hold SEND for 2+ seconds to log a full combustion report.
AUX display
O2% 20.9
COP 00
11 : 55 : 02
BAT 59
- The default AUX (auxiliary) display is shown
The parameters on lines 1, 2, 3 and 4 can be set independently
To customise the AUX display select MENU / SCREEN / AUX.
They remain the AUX parameters until changed again by the user.
Press SEND to print a full combustion test. (Also sends to PC if Wireless module fitted).
Hold SEND for 2+ seconds to log a full combustion report.
4. PRESSURE TEST (Also see section 9)
Select “Prs”. The pump stops. Press the PUMP button to auto-zero the pressure sensor.
Using the black connectors and manometer hose connect to P1 for single pressure or P1
and P2 for differential pressure.
PRS display
PRESSURE
P -0.04
mbar
12 : 56 : 29
- Defaults to smoothing ‘off’ on start-up. Can be changed via “Menu”.
- Defaults to ‘low’ resolution on start-up. Can be changed via “Menu”.
- Pressure units can be changed via “Menu”.
- Displays time to enable manually timed tests.
Press SEND to print a pressure test. (Also sends to PC if Wireless module fitted).
Hold SEND for 2+ seconds to log a pressure report.
5. LET-BY and TIGHTNESS TESTING (Also see section 9)
Select “Tightness”. The pump stops. Press the PUMP button to auto-zero the pressure
sensor. Select “yes” or “no” for the let-by test by using or , then press . Connect
from the test point to P1 using a black connector and manometer hose. Adjust the gas
pressure as you would with a “U” tube manometer. Press to start either the let-by
test or the stabilisation period…
LET BY
P1 10.35
P2 10.35
TIME 59
- Let-by test display.
- Pressure at the start of the let-by test
- Real time pressure reading
- Let-by default time is 1 minute. Can be changed via “Menu”.
When complete adjust the gas pressure if necessary then press to start the
stabilisation period…
STABIL’N
P1 20.00
mbar
TIME 59
- Stabilisation display.
- Real time pressure reading
- Stabilisation default time is 1 minute. Can be changed via “Menu”.
When complete adjust the gas pressure if necessary then press to start the tightness
test…
TIGHTN’S
P1 20.33
P2 20.33
TIME 119
- Tightness test display.
- Pressure at start of tightness test
- Real time pressure reading
- Tightness default time is 2 minute. Can be changed via “Menu”.
When complete the display will show…
LOG 06
P1 20.33
P2 20.26
PRINT
- Let-by and tightness test are automatically stored as a log number
- Pressure at start of tightness test
- Pressure at end of tightness test
- The test can be printed immediately or later from the memory
Note: The analyser’s memory can store up to 20 tightness tests. Tightness tests are logged
automatically therefore the tightness section of the memory will be full after the 20th
tightness test is complete. Before the 21st tightness test can be performed the
tightness section of the memory must be cleared. To do this select MENU / REPORT /
TIGHTN’S / DEL ALL / YES then press .
6. DIFFERENTIAL TEMPERATURE
Select “Diff Temp” to measure flow, return and differential temperatures
DIFF TEMP display
TEMP
T1C 60.1
T2C 47.0
TC 13.1
- Pump automatically switches off when dial is moved to Diff Temp
- Use the T1 connection for the flow temperature sensor
- Use the T2 connection for the return temperature sensor
- Real time temperature difference
Press SEND to print a differential temperature test. (Also sends to PC if Wireless module
fitted).
Hold SEND for 2+ seconds to log a differential temperature report.
7. ROOM CO TESTING
Select “Room CO” for CO investigations. Please refer to user manual.
ROOM CO display
ROOM CO
COP 00
TEST 14
LOG 01
- Duration of this test is variable from 0 to 30 minutes as per BS7967
- Real time CO reading, (ppm)
- Test 00 = start. To stop the Room CO test press the PUMP button
- The complete Room CO test is automatically stored as a log number
8. OTHER DISPLAY CODES
-PO- = Pump Off
-OC- = Open Circuit on temperature input
9. FOR BEST PRESSURE SENSOR ACCURACY
1) Switch the analyser on for 5 minutes to let the temperature stabilise.
2) Zero the pressure sensor when the analyser in the exact position that it will be
used.
10. TO FULLY CHARGE NiMH RECHARGEABLE BATTERIES
1) The analyser must be switched on.
2) Connect the charger and switched it on; charging indicator illuminates.
3) Switch the analyser off; the display will show “BATTERY CHARGING”.
4) The BAT status number of fully charged NiMH batteries is typically 70+
11. USING THE MENU
Select “Menu” on the rotary switch and navigate using the function buttons…
= Scroll up = Scroll down
= Enter
MAIN MENU SUB MENU OPTIONS / COMMENTS
SETUP SET FUEL NAT GAS, L OIL (28/35 sec), PROPANE, BUTANE, LPG, PELLETS
(Wood)
N C G EfN = nett efficiency, EfG = gross efficiency, EfC = condensing efficiency
SET TIME Uses Military time. 7am = 07:00, 7pm = 19:00
SET DATE Uses DD-MM-YY format
PRESSURE SMOOTH OFF = normal response. ON = slower (damped) response
RESOLVE LOW = normal. HIGH = displays to an extra decimal place
PS UNITS mbar, mmH2O, Pa, kPa, PSI, mmHg, hPa, InH2O
TIMES
LET-BY = Set duration of let-by test in minutes. Default = 1 minute
STABIL’N = Set duration of stabilisation in minutes. Default = 1 minute
TIGHTN’S = Set duration of tightness test in minutes. Default = 2 minute
REPORT COMB’N Stored combustion tests, VIEW, DEL ALL or EXIT (max = 99 tests)
PRESSURE Stored pressure tests, VIEW, DEL ALL or EXIT (max = 20 tests)
TIGHTN’S Stored let-by and tightness tests, VIEW, DEL ALL or EXIT, (20 tests)
TEMP Stored differential temperature tests, VIEW, DEL ALL or EXIT (20 tests)
ROOM CO Stored room CO tests, VIEW, DEL ALL or EXIT (max = 20 tests)
SCREEN CONTRAST Factory setting is 04
AUX Enables users to customise the parameters on the AUX display
User can set any parameter on lines 1, 2, 3 and 4
HEADER Sets printout header, 2 lines, 20 characters per line
SERVICE CODE Password protected for authorised service agents. Leave set to 0000.
To EXIT EACH Sub MENU select EXIT.
To EXIT the MENU move the rotary switch to any position other than “Menu”.
Any changes that have not been “entered” will be ignored.
12. Printouts
KANE455 V 1.00B
YOUR COMPANY NAME &
PHONE NUMBER HERE
SERIAL NO. 000000000
KANE455 V 1.00B
YOUR COMPANY NAME &
PHONE NUMBER HERE
SERIAL NO. 000000000
KANE455 V 1.00B
YOUR COMPANY NAME &
PHONE NUMBER HERE
SERIAL NO. 000000000
DATE 01/07/14 PRESSURE DIFF TEMP
TIME 12:00:08
DATE 01/07/14 DATE 01.07/14
COMBUSTION TIME 12:00:08 TIME 12:00:08
FUEL NAT GAS PRS mbar -0.037 T1
o
C 60.1
O2 % 5.4 T2
o
C 47.0
CO2 % 8.8 ∆T
o
C 13.1
CO Ppm 12 Customer
FLUE
o
C 55.1
INLT
o
C 17.2 Appliance Customer
NETT
o
C 37.9
Ref. Appliance
EFF (C) 98.3
LOSSES 1.7 Ref.
XAIR % 34.8
-----------------------------------------------------
C a l . d u e o n 0 1 / 0 7 / 1 5
----------------------------------------------------- KANE455 V 1.00B
YOUR COMPANY NAME &
PHONE NUMBER HERE
SERIAL NO. 000000000
CO/CO2 0.0001
KANE455 V 1.00B
YOUR COMPANY NAME &
PHONE NUMBER HERE
SERIAL NO. 000000000
PRS mbar 0.00
Customer ROOM CO TEST
Appliance LOG 01 LOG 04
DATE 01/07/14 DATE 01/07/14
Ref. TIME 12:00:08 TIME 12:00:08
TEST CO ppm LET BY TEST
0
1 PRS-1 mbar 10.12
2 PRS-2 mbar 10.11
3 LET-BY MINS 1:00
4
5 TIGHTNESS TEST
6
7 PRS-1 mbar 20.12
8 PRS-2 mbar 20.10
9 ∆PRS mbar -0.02
30
STABIL’N
MINS
1:00
TIGHTN’S MINS 2:00
MAXIMUM CO 11
Customer
Customer
Appliance
Appliance
Ref.
Ref.
PRODUCT REGISTRATION
Please complete, detach and return to: Kane International Ltd
Kane House, Swallowfield, Welwyn Garden City, Hertfordshire, AL7 1JG
Your Details
Name:
Job Title:
Company Name:
Company Address 1:
Address 2:
Town/City:
County:
Postcode:
Country:
Phone Number:
Fax Number:
Mobile Number:
Email Address:
Product Details
Note: Proof of Purchase may be required for warranty claims.
Date Purchased:
as numbers (28.01.14):
Purchased From:
Model Number: KANE455
Product Serial Number:
located on the rear product label
beneath the protective rubber sleeve
Why did you buy a Kane Product?
Made in the UK Previous Owner
Value for Money Our Fixed Price Servicing Programme
Kane Brand Dealer Recommendation
Not your Decision Other:
What brand was your previous analyser?
How did you hear about Kane?
Magazine Advert Trade Counter
Training School Previous Owner
Personal Recommendation Internet Search
Exhibition Other:
Which do you read most often?
Often Sometimes Hardly Ever
Registered Gas Engineer
Gas Installer
P.H.P.I.
P.H.A.M. News
Heating Ventilating & Plumbing
Heating & Plumbing Monthly
Your feedback is important to us, please add any additional comments
you would like to make with regard to your recent Kane purchase:
Thank you for completing this survey.
All the information we have collected is confidential.
We do not sell or share data with any other company or organisation.
Andere Handbücher für 455
1
Inhaltsverzeichnis
Andere Kane Messgerät Handbücher
Kane
Kane KANE958 Bedienungsanleitung
Kane
Kane 457 Bedienungsanleitung
Kane
Kane KANE101 Bedienungsanleitung
Kane
Kane KANE3500 Series Bedienungsanleitung
Kane
Kane 250 Bedienungsanleitung
Kane
Kane KANE455 Bedienungsanleitung
Kane
Kane KANE452NO Bedienungsanleitung
Kane
Kane 258 Bedienungsanleitung
Kane
Kane KANE458 Bedienungsanleitung
Kane
Kane 457 Bedienungsanleitung
Kane
Kane 250 Bedienungsanleitung
Kane
Kane KANE458s Bedienungsanleitung
Kane
Kane KANE458s Bedienungsanleitung
Kane
Kane 455 Bedienungsanleitung
Kane
Kane 79 Bedienungsanleitung
Kane
Kane EGA-4 Bedienungsanleitung
Kane
Kane AUTO600 Bedienungsanleitung
Kane
Kane KANE458s Bedienungsanleitung
Kane
Kane KANE251 Bedienungsanleitung
Kane
Kane CO2 Bedienungsanleitung
