Kane CO2 Bedienungsanleitung
Instruction Manual
KANE-CO2
Indoor Carbon
Dioxide Monitor
Inventory No: MAN00134
Rev.: 0.00000
January 2021
1
1
1
2
3
3
4
5
6
7
12
14
Contents
Getting Started
Packing List
Features at a Glance
Overview
General Operation & Settings
Operating Instructions
LCD Display
Trend Chart Display
Max/Min
Main Menu Functions
Specifications
Appendix
Features:
•Large Display
•Touch Button Operation
•15° Bevel Design, Easy to Read
•Low Drift NDIR Sensor, Long Lifespan
•Audible & Visible Alarm
•Chart with Variable Time Zoom Levels
•CO2/RH/Temperature Monitor Tracer
•Auto-Calibration & Manual Calibration
•Max/Min Value Display in Certain Time
Thank you for purchasing our desktop KANE-CO2 monitor. This product is used to
monitor CO2 concentration, humidity(RH) & temperature(TEMP) for indoor
air quality monitoring
Getting Started
Contents:
•CO2 Monitor Unit
•USB Cable for Power
•User Manual
•AC Adapter (Optional)
1
1
3
4
5
6
8
7
2
11
12
13
14
15
16
15
16
10
9
Front Panel Good Level
Low Level
Hole for Rope
Hole for Screws
USB Port
LCD
Button
Button
Button
Button
Power Indicator
High Level
Item ItemDescription Description
Overview
Drawing Sketch & Components List
Hole for Sensors
Hole for Buzzer
Label
1
3
4
5
6
8
7
10
11
12
9
213
14
2
•Use provided USB cable to connect the device. Once the countdown is complete,
your device is ready to use. See detail in Page 3.
•Use & buttons to switch timeline & CO2/RH/TEMP. The trend chart
displays the history records for any of the three parameters. See detail in Page 5.
•To restore factory defaults, hold for 4 seconds until an audible beep is heard.
•Press once will bring up the main menu. To select the function, press /
button. See detail in Page 7.
•Select to switch human and plants modes. See detail in Page 8.
•Select to change the high/low alarms for human and plant . See detail in
Page 11.
•Enter to switch alarm and mute . See detail in Page 8.
•Enter to switch temperature units C and F. See detail in Page 10.
General Operation & Settings
Operating Instructions
1. When first unboxing, plug in the unit with the
provided USB cable as shown on the right.
2. Once successfully connected, the power indicator
& 3 LEDs flash one by one.
3. Main display shows a countdown from 10.
Once the countdown is complete, your
product is ready to use. No initial setup
or calibration is needed
3
19
20
21
22
23
24
25
26
27
ItemItem Name Name
CO2/RH/TEMP Chart
Max Reading of Chart
Min Reading of Chart
RH Reading
Main Menu
CO2 Reading
Time per Division - indicates the
Plant Mode
Human Mode
Audible Alarm On/Off
17
18
Temperature Reading C / F
o o
chart’s span of time
4
17
18
19
20
21
22
23
24
25
26
27
LCD Display
The below chart displays the past readings for any of the three parameters (CO2/RH
/TEMP). There are 4 modes that can be toggled by using key: CO2, TEMP, RH,
& Cycle(automatically cycles through CO2/TEMP/RH)
Press will toggle the available Zoom Levels for each parameters.
(Minute/Hour/Day/Week)
Trend Chart Display
Press Press Press
Press
Press
Press
Press
Press
5
Zoom Level (Time Span) Time per Division
1M (minute) 5sec /div
1H (hour) 5m / div
1D (day) 2h / div
1W (week) 0.5d / div
Max / Min
Below is a table that shows the available Zoom Levels for all parameters CO2/RH/
TEMP, as well as the duration of each division for corresponding Zoom Levels:
At the top right corner of the display, there are two numerical indicators: MAX &
MIN. As the Zoom Level is changed, the MAX & MIN values will reflect the
maximum & minimum values on the chart of the selected parameter
(CO2, RH & TEMP).
6
The Main Menu functions can be actived by pressing . Pressing / once
will bring up the main menu, with an underlining flashing bar indicating the
current choice.
Main Menu Functions
Press
Press
Press
No pressing any
button in 1 minute
/ Press
/
Press
/
Press
/
Press
Press
7
Select number 0 to enter human mode. 0 is defaulted as human mode, unchangeable.The
preset Low & high alarm are 800 & 1200ppm. Enter "ADV" to adjust them if necessary.
In plant mode, it allows user to select between types of plants for optimal setting by using
/ cycles through 1~9. See number references with corresponding alarm settings in
high & low alarms in Page 14.
When ALARM display , an audible alarm will sound if the CO2 level exceeds
preset CO2 alarm value; means MUTE.
To select the function, press when it is underlined by the flashing bar. Note that
after 30 seconds if nothing is pressed, the Main Menu will disappear & the device
will revert to the normal state.
Press /
Press
Press (main interface)
(main interface)
Press
Press
Function Description
ALARM
PLANT
Press
Press
Press
PressPress
Press
PressPress
Press
Press
Main
interface
8
Press
Press
Inhaltsverzeichnis
Andere Kane Messgerät Handbücher
Kane
Kane 100-1 Bedienungsanleitung
Kane
Kane 905 Bedienungsanleitung
Kane
Kane KANE455 Bedienungsanleitung
Kane
Kane KANE200 Bedienungsanleitung
Kane
Kane EGA-4 Bedienungsanleitung
Kane
Kane KANE958 Bedienungsanleitung
Kane
Kane 455 Bedienungsanleitung
Kane
Kane KANE452NO Bedienungsanleitung
Kane
Kane KANE-PU690V Bedienungsanleitung
Kane
Kane AUTO600 Bedienungsanleitung
Kane
Kane AUTOplus 4-2 Bedienungsanleitung
Kane
Kane 458s Bedienungsanleitung
Kane
Kane ALERT-CO2 Bedienungsanleitung
Kane
Kane Hawk5000 Bedienungsanleitung
Kane
Kane KANE101 Bedienungsanleitung
Kane
Kane 457 Bedienungsanleitung
Kane
Kane 358 Bedienungsanleitung
Kane
Kane KANE900 Plus Bedienungsanleitung
Kane
Kane KM9106 Bedienungsanleitung
Kane
Kane 250 Bedienungsanleitung
