Key Digital KD-X411ProK Bedienungsanleitung

HDBaseT/HDMI via Single CAT5e/6 (Tx+Rx Set) Extenders, with

Audio De-embedding, EDID Control, Hot Plug Control, Full Buffer System,

IR Sensor, Up/Down IR & RS-232, support Ultra HD/4K & HDCP2.2

Power over HDBaseT/HDMI via Single CAT5e/6 (Tx+Rx Set) Extenders,

with Audio De-embedding, EDID Control, Hot Plug Control, Full Buffer

System, IR Sensor, Up/Down IR & RS-232, support Ultra HD/4K & HDCP2.2

KD-X411ProK

KD-X411POHK

Rev 0 – Sept 2015

Operating Instructions

Key Digital®, led by digital video pioneer Mike Tsinberg,

develops and manufactures high quality, cutting-edge

technology solutions for virtually all applications where

high-end video and control are important. Key Digital®

is at the forefront of the video industry for Home Theater

Retailers, Custom Installers, System Integrators,

Broadcasters, Manufacturers, and Consumers.

The Experts in Digital Video Technology and Solutions™

Key Digital®Systems :: 521 East 3rd Street :: Mount Vernon, NY 10553

Phone : 914.667.9700 Fax : 914.668.8666 Web : www.keydigital.com

KD-X411ProK_X411POHK_Manual.indd 2-3 11/17/15 12:40 PM

4 1

About KD-X411ProK/KD-X411POHK

KD-X411ProK/KD-X411POHK HDBaseT/HDMI (Tx & Rx) Extenders are an HDCP

2.2 compliant product that extend 4K/UHD 24/25/30 (4:4:4) and 4K/UHD 60 (4:2:0)

signals up to 150 ft. using Key Digital

KD-CAT6STP1X Super CAT6A Shielded cable,

or up to 125 ft. using a single third-party CAT5e/6 cable. 1080p/60, 1920x1200, 3D

signals are extended up to 250 ft. via single Key Digital

KD-CAT6STP1X Super CAT6A

shielded cable, or up to 230 ft. using a single third-party CAT5e/6 cable. In addition to

HDMI video and audio signals, KD-X411ProK/POHK carries IR, RS-232 and TCP-IP

signals for controlling remotely located equipment. Audio de-embed ports on the Tx

unit enable external audio connectivity with audio distribution systems and ampliﬁers.

Key Features

➔

HDBaseT via Single CAT5e/6 UTP/STP Extension:

With fully automatic

adjustment of feedback, equalization, and ampliﬁcation depending on

cabling length

➔

KD-X411POHK:

Features power extension from Tx to Rx with Power Over

HDBaseT, Rx unit does not require power supply

➔

Signal Extension:

»Up to 150 ft. @ 4K 24/25/30(4:4:4)/60(4:2:0) using KD-CAT6STP1X cabling

»Up to 125 ft. @ 4K 24/25/30(4:4:4)/60(4:2:0) using third-party CAT5e/6

UTP/STP cabling

»Up to 250 ft. @ 1080p / 1920x1200 using KD-CAT6STP1X cabling

»Up to 230 ft. @ 1080p / 1920x1200 using third-party CAT5e/6 UTP/STP

cabling

➔

4K/Ultra HD Resolution:

Support for 4096x2160 or 3840x2160 24/25/30Hz at

4:4:4/8 Bit or 60Hz at 4:2:0/8 Bit

➔

Audio De-Embedding:

Audio from the HDMI input is de-embedded through the

Coax digital (PCM) and/or Analog L/R audio output

➔

HDMI®and HDCP Licensing:

Fully licensed and compatible with HDCP 2.2 and

HDMI latest technology such as 4K/UHD 4:2:0/8bit at 60f/s

➔

EDID Control:

Internal library features 15 default EDID conﬁgurations and

native EDID data from Output/Display devices connected via Rx

Table of Contents

About KD-X411ProK/KD-X411POHK ..................................1

Quick Setup Guide ................................................3

Installation and Operation ...........................................3

Application Example ...............................................5

Connections .....................................................6

Audio De-Embedding Outputs........................................8

Extending IR or RS-232 Control.......................................9

Settings.........................................................12

LED Indicator Lights ...............................................16

RS-232 Commands ...............................................17

Speciﬁcations ....................................................19

Important Product Warnings & Safety Instructions .........................20

How to Contact Key Digital

.........................................21

Warranty Information ...............................................22

Please read all instructions to insure safe operation of the product.

KD-X411ProK_X411POHK_Manual.indd 1 11/17/15 12:40 PM

2 3

➔

Hot Plug Detection Control:

Enables integrator to choose if active signal

voltage is forced to connected input devices

➔

Full Buffer System™:

Manages TMDS re-clocking / signal re-generation,

HDCP authentication with source & display, EDID Control handshake,

and Hot Plug control

➔

IR Sensor:

Sensor powering via +5V on Rx unit’s IR In port collects line-of-sight

IR from remote(s) without external IR connecting block

➔

Up/Down IR:

Two channels of IR enable control to/from devices connected

to Tx and Rx units

➔

RS-232:

Bi-Directional control to/from Tx and Rx unit on 3.5mm connector

➔

Rotary Switch RS-232 Control Mode:

Provides control of Tx unit as well as

connectivity status

➔

3D:

Support for standard 3D stereoscopic signal formats

➔

Deep Color Support:

12bit Deep Color video / 8bit color for 4K/UHD

➔

Lossless compressed digital audio:

Support for Dolby

TrueHD, Dolby

Digital

Plus and DTS-HD Master Audio

™

➔

CEC Support:

For inter-device control between main input and output

HDMI channel

➔

I2C Communication:

EDID and HDCP authentication to Display and Source

➔

Control System Support:

Compatible with Compass Control

, AMX

Control4

, Crestron

, RTI

, Savant, URC

, Leviton

etc.

KD-X411ProK Accessories

➔(2) 5V 2A DC Power Supplies (Screw-In Type), (2) Mounting Brackets,

(1) IR Emitter, (1) IR Sensor

➔KD-X411ProK requires power on both Tx and Rx units

KD-X411POHK Accessories

➔(1) 12V 2A DC Power Supply (Screw-In Type), (2) Mounting Brackets,

(1) IR Emitter, (1) IR Sensor

➔KD-X411POHK only requires power on the Tx unit, which extends power

to the Rx unit

Quick Setup Guide

Step 1: Find a safe and convenient location to mount or place your

KD-X411ProK/KD-X411POHK units

Step 2: Begin with the KD-X411ProK/KD-X411POHK Tx/Rx units and all

input/output devices turned off with power cables removed

Step 3: Connect your HDMI source to the input port of your

KD-X411ProK/KD-X411POHK Tx unit

Step 4: Connect your HDMI displays to the output port of your

KD-X411ProK/KD-X411POHK Rx unit

Step 5: Connect KD-X411ProK/KD-X411POHK Tx unit to

KD-X411ProK/KD-X411POHK Tx with CAT5e/6 cable

Step 6: Connect additional IR/RS-232 control connections and IR sensors

Step 7:

BEFORE connecting power supply to power outlet,

screw-in the power

supply to the KD-X411ProK/KD-X411POHK Tx units and KD-X411ProK

Rx unit

Step 8:

AFTER all connections are made, plug-in power supplies to

power outlets

Step 9: Power on input/output devices

Installation and Operation

Before permanently securing the unit for ﬁnal installation, test for proper operation

of the unit and cables in your system. It is recommended that you leave enough

ventilation space to provide sufﬁcient airﬂow and cooling.

You MUST use the Power Supply provided with your unit or you VOID

the Key Digital

Warranty and risk damage to your unit and associated

equipment.

KD-X411ProK_X411POHK_Manual.indd 3 11/17/15 12:40 PM

4 5

Application Example

iPad

WiFi

EDID Control

KD-MC1000

Master Controller

Satellite

RS-232

HDMI

CAT5e/6

KD-X411ProK

IR Out

Satellite

Remote

IR Sensor

IR In

WiFi Router

AVR

Surround

Multi-Zone Audio

4K up to 150’ with

Key Digital

KD-CAT6STP1X

Display

RS-232

IR Out

HDMI

Apple TV

PCM

L/R Audio

KD-X411ProK_X411POHK_Manual.indd 4-5 11/17/15 12:40 PM

6 7

➔Use the 3.5mm analog audio and/or PCM coaxial digital audio de-embed ports to

integrate with audio distribution systems, ampliﬁers, or AV receivers.

Rx Unit:

➔Using a short HDMI cable, connect your output / display device to the HDMI port

labeled “HDMI Output”.

➔Connect the CAT5e/6 cable at the port labeled “CAT5e/6 Input”.

➔If you are sending or receiving IR, connect included IR Sensor and/or IR Emitter

Connections

Before making any connections, power off your source and display devices.

Tx Unit:

➔Using a short HDMI cable, connect your source device to the HDMI port labeled

“HDMI Input”. To connect DVI or Display Port, use appropriate adapters.

➔Connect the CAT5e/6 cable that connects to the Rx Unit at the port labeled

“CAT5e/6 Output”.

➔Make IR In and Out connections to receive (IR In port) or send (IR Out port)

control signals.

Refer to the “Extending IR & RS-232 Control” for more information.

➔Connect a 3.5mm Stereo cable for bi-directional RS-232 control.

Refer to the “Extending IR or RS-232 Control” and the “RS-232 Commands”

section for more information.

KD-X411ProK_X411POHK_Manual.indd 6-7 11/17/15 12:40 PM

8 9

Extending IR or RS-232 Control

RS-232:

Bi-directional RS-232 is achieved utilizing the RS-232 port on the Tx and Rx units.

The connector is 3.5mm stereo and the pinout is the same on the Tx and Rx unit.

➔RS-232 Pass-through Mode

»Send and receive (bi-directional) RS-232 commands for controlling remote

equipment.

➔Control Mode

»Provides control of Tx units as well as connectivity status

»See RS-232 Commands section for more information

➔Firmware Upgrade Mode

»Two different types of ﬁrmware may be updated:

MCU (KD-X411ProK/KD-X411POHK units),

and HDBaseT (extension over CAT5e/6)

RS-232 Cabling

3.5mm stereo to RS-232 adapter cables are available through Key Digital and other

wire suppliers, and can also be fabricated by skilled technicians.

3.5mm stereo to Female DB9

connector (not included).

Key Digital part KD-3.5FDB96.

Typically used to connect to the COM

port of the computer or master controller.

➔If you are transmitting or receiving RS-232, connect to the RS-232 port

➔

After all the connections are made, connect power to the Tx and Rx

(KD-X411ProK only) using the included power supplies and then power up

your source and display equipment.

Audio De-Embedding Outputs

Analog L/R Audio Output (3.5mm Stereo):

➔Provides de-embedded 2ch analog audio output

from HDMI input source

Digital Audio Output (Digital Coaxial RCA):

➔Provides de-embedded Digital Audio Output from HDMI input

Notes:

➔There are no volume or tone control features

➔There are no DSP features. Ie, in order to achieve 2ch analog audio output,

the HDMI input source audio format must be 2ch

➔External audio connectors may be set off via RS-232.

See the RS-232 Commands section for more information.

Audio Input

Signal Format

Analog L/R

Output

Digital Audio

Output

2CH PCM Pass-through Pass-through

Multi-Channel PCM MUTE MUTE

DOLBY/DTS MUTE Pass-through

HD Audio MUTE MUTE

KD-X411ProK_X411POHK_Manual.indd 8-9 11/17/15 12:40 PM

10 11

Rx Unit / IR Sensor:

»IR Sensors can be connected directly into the Rx unit’s IR In port, without

the need for an external IR distribution block

»IR signal on the Tip, with 5V powering of the IR sensor on the Ring.

IR In Tip Ring Sleeve Typical 3.5mm

Connector-type

Serial IR (Tx) IR In N/C Ground Mono

IR Sensor (Rx) IR In 5V Ground Stereo

➔IR Out:

»Pass-through from signal of corresponding IR In port, as determined by the

position of the Control Rotary

»Driving power: 5V with 32mA minimum current

»Typically connected with an IR emitter

IR Out Tip Ring Sleeve Control Rotary Position

Serial IR IR Out N/C Ground Any

IR Cabling

Your KD-X400ProK/KD-X400POHK includes an IR Sensor and an IR Emitter.

Signal acceptance:

The IR Sensor receives signals from a 90° angle at up to 30 ft.

away. It accepts a maximum IR burst frequency of 55kHz.

Only

the included IR sensors are compatible with the KD-X411ProK/KD-X411POHK.

Third-party IR Sensors may not work with KD-X411ProK/KD-X411POHK

The included IR Sensor.

The 3.5mm connector is

stereo

and it connects to

the

IR In

port of the Rx unit.

3.5mm stereo to Male DB9 connector

(not included).

Key Digital part KD-3.5MDB96.

Typically used to connect to the controlled

device.

RS-232 Mode Tip Ring Sleeve Control Rotary

Pass-through Tx Rx Ground 0-7

Control Mode Tx Rx Ground 8, 9

F/W MCU Tx Rx Ground A, B

F/W HDBaseT Tx Rx Ground C, D, E, F

Bi-directional IR control extension is supported.

»“IR In” port on the Tx unit extends to the “IR Out” port of the Rx unit

»“IR In” port on the Rx unit extends to the “IR Out” port of the Tx unit

➔IR In: The IR In port is different for the Tx and Rx units. The Tx unit’s IR In port

supports a Serial IR (hardwired) connection. The Rx unit’s IR In port supports an

IR Sensor.

Tx Unit / Serial IR:

»A ﬁxed 5V input signal with a 3.5mm mini jack

»IR signal on the tip. Mono or stereo 3.5mm mini jacks are supported, with

the ring open / having no contact.

»Typically fed from a dedicated control system or an IR distribution block

KD-X411ProK_X411POHK_Manual.indd 10-11 11/17/15 12:40 PM

12 13

61080p, HD AUDIO

Rotary EDID

Switch:

74Kx2K@30, 2CH AUDIO

84Kx2K@30, DOLBY/DTS 5.1

94Kx2K@30, HD AUDIO

Control Rotary

The Control rotary enables the integrator to choose the

desired setting for RS-232 Mode and Hot Plug Detection

Control Mode.

In many settings, the Control rotary setting may not match on

the Tx and Rx units.

IMPORTANT! Please apply light pressure to the

Control rotary when making your selection

Control Rotary Position Assignments:

Position RS-232 Mode Hot Plug Detection Control

0 Pass-Through Bypass

1 Pass-Through Bypass

2 Pass-Through Forced HPD On

3 Pass-Through Forced HPD On

4 Pass-Through Bypass

5 Pass-Through Bypass

6 Pass-Through Forced HPD On

7 Pass-Through Forced HPD On

The included blinking-type IR Emitter.

The 3.5mm connector is

mono

and it connects to

the

IR Out

port of the Tx or Rx unit.

The sleeve of the 3.5mm Male connector must have good physical contact

with 3.5 mm Female input/output on the KD-X411ProK/POHK.

Some 3.5mm Male plugs feature a plastic

sleeve that extends longer than an average

sleeve. This may cause poor grounding

contact. See the example on the left.

Settings

EDID Control

EDID authentication is provided from the KD-X411ProK/KD-X411POHK Tx unit to

the connected input / source device. The EDID ﬁle (AKA “handshake”) is selected

using the EDID Control rotary on the Tx unit and provides a list of compatible video

and audio formats as well as digital data, informing the source device what it should

output. Most sources will comply with a new EDID ﬁle without a power-cycle, but

each source may behave differently. Adjustments

Default EDID Control Table

0Copy EDID from CAT5e/6 Output A4Kx2K@60, 2CH AUDIO

11080i, 2CH AUDIO B4Kx2K@60, DOLBY/DTS 5.1

21080i, DOLBY/DTS 5.1 C4Kx2K@60, HD AUDIO

31080i, HD AUDIO D1280x720p@60 DVI (no audio)

41080p, 2CH AUDIO E1920x1080p@60 DVI (no audio)

51080p, DOLBY/DTS 5.1 F1080p, 2CH AUDIO

KD-X411ProK_X411POHK_Manual.indd 12-13 11/17/15 12:40 PM

14 15

NOTE: Use shielded metal RJ45 connectors with

soldered ground wires when terminating shielded

CAT5e/6. Key Digital part: KD-RJ45SC (compatible

with KD-CAT6STP1X and other third-party CAT6/STP)

8 Control Mode Bypass

9 Control Mode Bypass

A Firmware Upgrade for MCU Forced HPD On

B Firmware Upgrade for MCU Forced HPD On

C Firmware Upgrade for HDBaseT Bypass

D Firmware Upgrade for HDBaseT Bypass

E Firmware Upgrade for HDBaseT Forced HPD On

F Firmware Upgrade for HDBaseT Forced HPD On

Forced Hot Plug Detection (HPD)

Hot Plug Detection (HPD) may be forced on the Tx Rx unit in order to provide

connected devices with necessary voltage to inform the device that a partner

(display) is connected and active. If the Control rotary is set to any HPD Bypass

setting, HPD signals from the output to the input device will pass as normal. In

cases of many layers of connectivity, HPD may be lost leading to no signal at the

display. In those cases, ﬁx the Control rotary to any Forced HPD setting.

Range and Resolution:

Distance performance is significantly increased when using Key Digital

KD-CAT6STP1X Super CAT6/STP Cabling.

➔Up to 150 ft. @ 4K 24/25/30(4:4:4)/60(4:2:0) using KD-CAT6STP1X cabling

➔Up to 125 ft. @ 4K 24/25/30(4:4:4)/60(4:2:0) using third-party CAT5e/6 UTP/

STP cabling

➔Up to 250 ft. @ 1080p / 1920x1200 using KD-CAT6STP1X cabling

➔Up to 200 ft. @ 1080p / 1920x1200 using third-party CAT5e/6 UTP/STP cabling

KD-X411ProK_X411POHK_Manual.indd 14-15 11/17/15 12:40 PM

16 17

RS-232 Commands

RS-232 Pinout:

Tip Ring Sleeve

Tx Rx Ground

Connection protocol is as follows:

➔Baud Rate = 57600 bits per second

➔Data Bits = 8

➔Stop Bits = 1

➔Parity = None

➔Flow Control = None

➔Carriage Return: Required

➔Line Feed: Required

Commands are not case-sensitive. Spaces shown below may be excluded.

Carriage return and line feed is required at the end of each string.

Commands:

KD-X411ProK> H

-------------------------------------------------------------------------

-- Key Digital Systems HELP --

-------------------------------------------------------------------------

-- KD-X411ProK System Address : 00 F/W Version : 1.00 --

-- Azz : All Commands may have Prex System Address zz=[01-99] --

-- H : Help --

-- STA : Global Status --

-- SPCA xx : Set System Address, xx = [00-99] (00=Single) --

-- --

-- Video I/O Setup Commands: --

-- SPO DBG ON/OFF : Set Output DGB ON/OFF --

-- SPO ON/OFF : Set CAT5e/6 Output ON/OFF --

-- --

-- Audio Output Setup Commands: [E=Enable, D=Disable] --

-- SPO AA E/D : Enable/Disable External Analog Audio Output --

-- SPO DA E/D : Enable/Disable External Digital Audio Output --

-- --

-- SPC RSB z : Set RS232 Baud Rate to z bps, z=[0-4] --

-- [0:57600, 1:38400, 2:19200, 3:9600, 4:4800] --

-------------------------------------------------------------------------

LED Indicator Lights

Power:

»Color: Green

»Solid illumination during power on state, as provided by healthy connection

with power supply.

»Steady blink if power is not adequate and/or if there is a connectivity problem

with the KD-X411ProK/ KD-X411POH Rx unit

HDMI Active (HDMI Input/Output):

»Color: Blue

»Tx Unit: Solid illumination from active signal (HDMI TMDS) reception from

connected source device

»Rx Unit: Solid illumination from active Hot Plug Detection voltage with

connected display/output device

»If Hot Plug Detection is forced to input device from Tx unit, the HDMI Active

light will illuminate solid regardless of HDMI signal from connected device.

CAT5e/6 Input/Output:

»Color: Blue

»Tx Unit: Solid illumination from active link and Hot Plug Detection voltage

from Rx unit

»Rx Unit: Solid illumination from active link with Tx unit

KD-X411ProK_X411POHK_Manual.indd 16-17 11/17/15 12:40 PM

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Key Digital Extender Handbücher

Key Digital

Key Digital Smart Baluns KD-BBRX Bedienungsanleitung

Key Digital

Key Digital Phantom KD-HD1X1ProK Bedienungsanleitung

Key Digital

Key Digital FatCAT KD-CATHD250Lite Bedienungsanleitung

Key Digital

Key Digital KD-4KWHCEX Bedienungsanleitung

Key Digital

Key Digital KD-CAT5XCAT5 Bedienungsanleitung

Key Digital

Key Digital KD-X600ProK Bedienungsanleitung

Key Digital

Key Digital FatCAT KD-CATHD Tx Bedienungsanleitung

Key Digital

Key Digital KD-HDB150 Bedienungsanleitung

Key Digital

Key Digital KD-IP120TX Bedienungsanleitung

Key Digital

Key Digital KD-CAT5XCAT5 Bedienungsanleitung

Key Digital

Key Digital KD-X444SP Bedienungsanleitung

Key Digital

Key Digital KD-X222 Bedienungsanleitung

Key Digital

Key Digital KD-PS22UTx Bedienungsanleitung

Key Digital

Key Digital KD-HDB150 Bedienungsanleitung

Key Digital

Key Digital KD-X222PO Bedienungsanleitung

Key Digital

Key Digital KD-EX18G Bedienungsanleitung

Key Digital

Key Digital KD-XUSB2 Bedienungsanleitung

Key Digital

Key Digital KD-X444SP Bedienungsanleitung

Key Digital

Key Digital KD-HDMIXCAT5 Bedienungsanleitung

Key Digital

Key Digital PRO Connect PCBKDCATHD Tx Bedienungsanleitung

Key Digital

Key Digital KD-FIX418 Bedienungsanleitung

Key Digital

Key Digital KD-X422POA Bedienungsanleitung

Key Digital

Key Digital KD-X422WP Bedienungsanleitung

Key Digital

Key Digital KD-X444LP Bedienungsanleitung

Beliebte Extender Handbücher anderer Marken

SY HDBT-60T Bedienungsanleitung

Appsys ProAudio

Appsys ProAudio ADX-16 Bedienungsanleitung

Atlona

Atlona RS232 Bedienungsanleitung

IDK

IDK OPF-TH1000-A Bedienungsanleitung

Enable-IT

Enable-IT 824WP Bedienungsanleitung

Worx

Worx Landroid RadioLink WA0864 Technisches Datenblatt

TP-Link

TP-Link TL-WA730RE Bedienungsanleitung

Camplex

Camplex CMX-HDMI-SFPL Bedienungsanleitung

SC&T

SC&T HE03-4K Bedienungsanleitung

Samsung

Samsung SCS-26UC4 Bedienungsanleitung

Foxun

Foxun SX-GES24 Bedienungsanleitung

MuxLab

MuxLab 500771 Bedienungsanleitung

foxunhd

foxunhd SX-AEX01 Bedienungsanleitung

TERK Technologies

TERK Technologies LFIRX2 Bedienungsanleitung

Devolo

Devolo Audio Extender Handbuch

Edimax

Edimax EW-7438RPn V2 Bedienungsanleitung

Shinybow USA

Shinybow USA SB-6335T5 Bedienungsanleitung

SECO-LARM

SECO-LARM ENFORCER EVT-PB1-V1TGQ Bedienungsanleitung