Keysight N9020B Installations- und Betriebshandbuch

Notice: This document contains references toAgilent.

Please note that Agilent’s Test and Measurement

business has become Keysight Technologies. For

more information, go to www.keysight.com.

Keysight Technologies

N9020B MXA Signal Analyzer

Analog Baseband IQ Inputs (Option BBA) Upgrade Kit

Installation Note

Notices

The information contained in this document is subject to change without notice.

Keysight Technologies makes no warranty of any kind with regard to this material, including but

not limited to, the implied warranties of merchantability and fitness for a particular purpose.

Keysight Technologies shall not be liable for errors contained herein or for incidental or

consequential damages in connection with the furnishing, performance, or use of this material.

Manual Part Number

N9020-90257

Supersedes None

Edition

Edition 1, May 2016

Printed in USA/Malaysia

Published by:

Keysight Technologies, Inc.

1400 Fountaingrove Parkway

Santa Rosa, CA 95403

Installation Note N9020-90257 3

Option BBA, Analog Baseband I/Q Inputs Retrofit Kit

Products Affected: N9020B, MXA Signal Analyzer

Serial Numbers: All

Option BBA

To Be Performed By: (X) Keysight Service Center

(X) Personnel Qualified by Keysighta

( ) Customer

a.To ensure that this newly installed option is functioning properly, the procedure that follows includes the

requirement of performing certain adjustments and performance verification tests. However, the completion of

these tests does not guarantee that the instrument meets all advertised specifications.

Software and test equipment is required for making adjustments and for performance verification testing.

Information on how to obtain this software can be found at:

www.keysight.com/find/calibrationsoftware

While Keysight does recommend that a full calibration be performed after the installation of this upgrade, the

end user must ultimately determine whether they want this service or not. If a full calibration is required,

arrangements regarding the level of calibration must be made between the end user and the calibration

provider.

Estimated Installation Time:

Estimated Adjustment Time:

Estimated Verification Time:

2.0 Hours

0.5 Hours

1.25 Hours

4Installation Note N9020-90257

Option BBA, Analog Baseband I/Q Inputs Retrofit Kit

Introduction

This procedure is used to retrofit Option BBA into the N9020B Signal Analyzer.

Installation Kit Parts List

Quantity Description Keysight Part Number

1 BBIQ Main Board N9020-60093

1 LED Board N9020-63095

1 BBIQ Interface Board N9020-60094

1 LED Board Overlay, Bottom N9020-80166

1 LED Board Overlay, Top N9020-80163

1Cable, Flexible Coaxa

a.This cable included in the N9030-60018 Opt BBA Cable Kit

8121-1401

1Cable, Flex Ribbonb

b.Only needed when installing on N9030B

8121-2090

1Cable, Flex Ribbonc

c.Only needed when installing on N9020B

8121-1683

1 Option BBA Cable Kit (with wire markers) N9030-60018

1 Core Bracket, top N9020-00071

1 Core Bracket, bottom N9020-00072

60 Screws, M3 X 0.5 (8 mm long) 0515-0372

1 Vibration Mount 0460-2725

15 Screws, M3 X 0.5 (6 mm long), flat head 0515-1946

9 Screws, M3 X 0.5 (8 mm long), flat head 0515-2032

2 Screws, Hex Shoulder N9020-20017

2 Main Board Warning Labels N9020-80036

1 Entitlement Certificate 5964-5178

1 Entitlement Certificate Envelope 5967-7169

5 Tie Wrap 1400-0249

1 Installation Note, MXA This note

1 Installation Note, PXA N9030-90077

1 Probe tip BNC adapter 5063-2143

1 Cable 8120-2682

Installation Note N9020-90257 5

Option BBA, Analog Baseband I/Q Inputs Retrofit Kit

Tools Required

— T-10 Torx Driver

— T-20 Torx Driver

— 5/16-inch torque wrench

— 1/4-inch socket on 4 lb torque wrench

—scissorsorknife

—diagonalcutters

— USB storage device with > 2 GB free memory

Keysight Service Center

The following kit items will not be installed in the analyzer upgrade and need to be shipped back to

the end user for their use:

— 5063-2143, Probe tip BNC adapter

— 8120-2682, cable

— Entitlement Certificate

Before you disassemble the instrument, turn the power switch to Standby and unplug the

instrument. Failure to unplug the instrument can result in personal injury.

Electrostatic discharge (ESD) can damage or destroy electronic components. All work on

electronic assemblies should be performed at a static-safe workstation. Refer to the

documentation that pertains to your instrument for information about static-safe workstations

and ordering static-safe accessories.

6Installation Note N9020-90257

Option BBA, Analog Baseband I/Q Inputs Retrofit Kit

Installation Procedure

Standard Instrument (Benchtop Configuration)

1. Disconnect the instrument from ac power.

2. Refer to Figure 1. Using the T-20 driver, remove the 4 screws (1) (two on each side) that

attach the strap handles (2) on each side of the instrument.

3. Remove the four key locks from the instrument four bottom feet.

4. Remove the four instrument bottom feet.

5. Using the T-20 driver, remove the four screws (including washers) (3) that hold the rear feet

(4) in place.

6. Pull the instrument cover (5) off towards the rear of the instrument.

If the instrument is placed on its face during any of the following procedures, be sure to use a soft

surface or soft cloth to avoid damage to the front panel, keys, or input connector.

Make sure any adapters on the front panel are removed.

If the analyzer has Option PRC, Portable Configuration, go to the “Portable Instrument

(Option PRC)” section to remove the outer case.

Installation Note N9020-90257 7

Option BBA, Analog Baseband I/Q Inputs Retrofit Kit

Figure 1 Benchtop Configuration Outer Case Removal

7. Proceed to the Front Frame Assembly Removal section to remove the front frame.

8Installation Note N9020-90257

Option BBA, Analog Baseband I/Q Inputs Retrofit Kit

Portable Instrument (Option PRC)

1. Disconnect the instrument from ac power.

2. Refer to Figure 2. Using the T-20 driver, remove the four screws (1), two on each side, to

detach the Bail Handle Assembly (2) from the front frame.

Figure 2 Bail Handle and Front Bumpers Removal (Option PRC)

3. Using the T-20 driver, remove the four screws (6) (two on each side) that attach the four strap

handle plugs (5) from both sides of the instrument.

4. Refer to Figure 3. Using the T-20 driver, remove the four screws including washers (1) that

hold the rear bumpers (2) in place.

5. Pull the instrument cover off towards the rear of the instrument.

Make sure any adapters on the front panel are removed.

Installation Note N9020-90257 9

Option BBA, Analog Baseband I/Q Inputs Retrofit Kit

Figure 3 Portable Instrument Outer Case Removal (Option PRC)

10 Installation Note N9020-90257

Option BBA, Analog Baseband I/Q Inputs Retrofit Kit

Front Frame Assembly Removal

1. Refer to Figure 4. Using the T-10 driver, remove the eight screws (1), four on each side, to

detach the front frame from the chassis.

Figure 4 Front Frame Removal

Inhaltsverzeichnis

Andere Keysight Messgerät Handbücher

Keysight

Keysight M9392A Benutzerhandbuch

Keysight

Keysight E4990A Bedienungsanleitung

Keysight

Keysight 537A Kurzanleitung

Keysight

Keysight 8990B Bedienungsanleitung

Keysight

Keysight 16034H Bedienungsanleitung

Keysight

Keysight N9010AK-MTU Installations- und Betriebshandbuch

Keysight

Keysight B2900A Bedienungsanleitung

Keysight

Keysight N9912A Bedienungsanleitung

Keysight

Keysight U1583B Bedienungsanleitung

Keysight

Keysight N5244/45AS Option H85 Handbuch

Keysight

Keysight E5063A Bedienungsanleitung

Keysight

Keysight 11590B Service-Handbuch

Keysight

Keysight M1970 Series Bedienungsanleitung

Keysight

Keysight 11644A R Bedienungsanleitung

Keysight

Keysight N9912A Bedienungsanleitung

Keysight

Keysight DOCSIS 3.1 Bedienungsanleitung

Keysight

Keysight N4391A Bedienungsanleitung

Keysight

Keysight x series Kurzanleitung

Keysight

Keysight E5071C Bedienungsanleitung

Keysight

Keysight N1911A Bedienungsanleitung

Keysight

Keysight M9703B Kurzanleitung

Keysight

Keysight PNA-X N5244A Bedienungsanleitung

Keysight

Keysight U8903A Bedienungsanleitung

Keysight

Keysight N1913 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung

Konica Minolta

Konica Minolta BC-10 Plus Bedienungsanleitung