Keysight N9030B Installations- und Betriebshandbuch

Option LNP Low Noise Path

Option MPB Microwave Preselector Bypass

Keysight N9030B PXA Signal Analyzers

Installation Note

Notices

The information contained in this document is subject to change without notice.

Keysight Technologies makes no warranty of any kind with regard to this material, including but

not limited to, the implied warranties of merchantability and fitness for a particular purpose.

Keysight Technologies shall not be liable for errors contained herein or for incidental or

consequential damages in connection with the furnishing, performance, or use of this material.

Manual Part Number

N9030-90082

Edition

Edition 1, February 2016

Printed in USA/Malaysia

Published by:

Keysight Technologies, Inc.

1400 Fountaingrove Parkway

Santa Rosa, CA 95403

Installation Note N9030-90082 3

Option LNP or Option MPB Installation Kit

Introduction

When a new instrument is ordered from the factory with either Option LNP or MPB enabled, the

instrument is assembled with hardware that supports both options. Therefore, instruments that

currently contain Option LNP can be upgraded to also contain Option MPB by licensing Option

MPB. Instruments that currently contain Option MPB can be upgraded to also contain Option LNP

by licensing Option LNP.

This installation note explains how to install Option LNP or Option MPB into instruments that

already contain one of these options.

If the instrument HAS frequency range option 508, 513, or 526 and DOES NOT currently contain

either Option LNP, or Option MPB, the hardware required to support these two options is not

contained in the instrument and the N9030BU-HL1 retrofit kit is required.

If the instrument HAS frequency range option 543, 544, or 550 and DOES NOT currently contain

either Option LNP, or Option MPB, the hardware required to support these two options is not

contained in the instrument and the N9030BU-HL2 retrofit kit is required.

Option LNP provides a switchable Low Noise Path, for input frequencies 3.6 GHz and greater. This

low noise path when activated allows enhanced DANL and SHI performance.

Option MPB provides a switchable microwave preselector filter bypass path for input frequencies

3.6 GHz and above. The preselector filter limits the bandwidth of the input signal and can cause

slight amplitude errors if the filter drifts.

Products Affected: N9030B PXA, Options 508, 513, 526, 543, 544, and 550

Serial Numbers: All

To Be Performed By: (X) Keysight Service Center

(X) Personnel Qualified by Keysight

(X) Customer

Estimated Installation Time:

Estimated Adjustment and Verification Time:

0.5 Hours

4 Hours (see Note 2)

4Installation Note N9030-90082

Option LNP or Option MPB Installation Kit

1. At the time of manufacture the hardware related to this option was fully

adjusted and the option performance was verified to be within its warranted

specifications. Within one year of the initial calibration date of the instrument

this option is fully calibrated with no further adjustment or verification testing.

To determine the initial calibration date, locate the original calibration

certificate that was shipped with the instrument at the time of purchase. The

Date of Calibration is printed on the original calibration certificate.

No factory test data is available for these options. If you require test data for

these options then a full calibration is required after installation of these

options. Arrangements regarding the level of calibration must be made with

the calibration provider.

2. If this instrument has been adjusted as part of a repair or calibration during its

first year, or if the instrument is more than one year old, additional

adjustments and performance verification tests are required to ensure that the

newly installed option is functioning properly. However, the completion of

these tests does not guarantee that the instrument meets all warranted

specifications.

3. The latest revision of the PXA software may be downloaded from

http://www.keysight.com/find/Xseries_software

4. These options are licensed for one instrument model/serial number

combination. The license key will only install on the designated instrument.

Installation Note N9030-90082 5

Option LNP or Option MPB Installation Kit

Contents

Tools Required

— Personal computer with internet access and USB port

— USB storage device with > 2 GB free memory

If adjustments and performance testing is required:

— Keysight Calibration and Adjustment Software, N7814A

— Test equipment and computer supported by the X-Series Performance Tests and Adjustment

Software.

Optional tools:

— Instrument Service Guide - is available online at the following URL:

www.keysight.com/find/N9030B_service_guide

Installation Procedure over USB

1. Locate the Option Upgrade Entitlement Certificate (5964-5178) from the kit.

2. Redeem the Option Upgrade Entitlement Certificate by following the instructions on the

Certificate.

3. After redeeming your Option Upgrade Entitlement Certificate you will receive an email with an

attached License File.

4. Locate a USB storage device. Perform a virus scan on this device before use.

5. Save the License File to the root directory of the USB storage device.

6. Connect the USB storage device to the signal analyzer USB port. Windows will detect the new

hardware and may display the configuration menu shown in Figure 1. This menu may be

configured according to your preferences.

Quantity Description Keysight Part

Number

1 Installation Note This note

1 Option Upgrade Entitlement Certificate 5964-5178

6Installation Note N9030-90082

Option LNP or Option MPB Installation Kit

Figure 1 USB Storage Device Configuration Menu

7. The signal analyzer will automatically consume the License File. (This may take a few minutes)

When the License File is consumed the Keysight License Manager will display a “Successful

License Installation” message similar to the one shown in Figure 2.

Figure 2 Successful License Installation

Alternate Installation Procedure

The License File can be manually installed over USB or LAN by placing the license file in the

following folder on the signal analyzer

C:\Program Files\Agilent\licensing

Verify the Installation

1. Cycle the instrument power and allow the instrument to boot to the measurement screen.

2. Press System, Show System to display a list of installed options.

3. Verify that Options N9030B-LNP and N9030B-MPB appear on the list.

Installation Note N9030-90082 7

Option LNP or Option MPB Installation Kit

Manually Control the Option

Assure the signal analyzer is in Spectrum Analyzer mode.

View the 4.8 GHz calibrator signal:

Preset the analyzer by pressing the green Mode Preset key.

Press Input/Output, RF Calibrator from the drop-down menu, and select 4.8 GHz.

Press FREQ, Center Frequency and enter 4.8 GHz. Press Span, enter 5 MHz.

Enable the Low Noise Path or the Preselector Bypass:

Press AMPTD, Signal Path, uW Path Ctrl.

Verify that the selections appear labeled "Low Noise Path Enable" and "uW Presel Bypass".

Tap Low Noise Path Enable. If the path was previously set to Standard Path, or uW Presel

Bypass, you should hear a "click".

Tap uW Presel Bypass. If the path was previously set to Standard Path, or Low Noise Path

Enable, you should hear a "click".

8Installation Note N9030-90082

Option LNP or Option MPB Installation Kit

Utilities, Adjustments, and Performance Verification Tests

Calibration Software and specified test equipment is required to perform the adjustments and the

performance verification testing. Information on how to obtain this software can be found at

http://www.keysight.com/find/calibrationsoftware

Utilities Required

None

Adjustments Required

If the instrument is more than one year old, or if this instrument has been adjusted as part of

calibration during its first year, the following adjustments are the minimum set required to ensure

that this newly installed option is functioning properly.

Performance Testing Required

If the instrument is more than one year old, or if the instrument has been adjusted as part of a

calibration during its first year, the following performance verification tests are the minimum set

required to ensure that this newly installed option is functioning properly. Performing only these

tests does not guarantee the instrument meets all specifications.

A full calibration is required to assure the instrument meets all specifications

The end user must ultimately determine whether they want a full calibration to be performed after

the installation of this upgrade or not. If a full calibration is required, arrangements regarding the

level of calibration must be made between the end user and the calibration provider.

For assistance, contact your nearest Keysight Technologies Sales and Service Office. To find your

local Keysight office access the following URL, or if in the United States, call the following

telephone number:

http://www.keysight.com/find/assist

1-800-829-4444 (8 am - 8 pm ET, Monday - Friday)

Adjustments

Adjustments dependent on performance verification test results

Performance Verification Tests

Perform all performance verification tests

This information is subject to change

without notice.

Edition 1, February 2016

N9030-90082

www.keysight.com

Andere Handbücher für N9030B

Inhaltsverzeichnis

Andere Keysight Messgerät Handbücher

Keysight

Keysight u1701b Handbuch

Keysight

Keysight N7020A Bedienungsanleitung

Keysight

Keysight P-Series Installationsanleitung

Keysight

Keysight N9912A Bedienungsanleitung

Keysight

Keysight N9020B Installations- und Betriebshandbuch

Keysight

Keysight N9010AK-MTU Installations- und Betriebshandbuch

Keysight

Keysight N9030A-503 Bedienungsanleitung

Keysight

Keysight E5071C ENA Series Bedienungsanleitung

Keysight

Keysight N1911A Bedienungsanleitung

Keysight

Keysight E5071C ENA Series Bedienungsanleitung

Keysight

Keysight M9602A PXIe Benutzerhandbuch

Keysight

Keysight N5221A Bedienungsanleitung

Keysight

Keysight 478A Service-Handbuch

Keysight

Keysight V3500A Bedienungsanleitung

Keysight

Keysight N774 C Series Betriebsanleitung

Keysight

Keysight N5222-60119 Installations- und Betriebshandbuch

Keysight

Keysight V3500A Bedienungsanleitung

Keysight

Keysight N432A Bedienungsanleitung

Keysight

Keysight N2780B Bedienungsanleitung

Keysight

Keysight N5244AU- H29 Installations- und Betriebshandbuch

Keysight

Keysight HeNe 5519A Bedienungsanleitung

Keysight

Keysight E5061B Bedienungsanleitung

Keysight

Keysight N2820A Bedienungsanleitung

Keysight

Keysight M9392A Benutzerhandbuch

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

ADTEK

ADTEK MW-5 Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung