Keysight PXA Series Installations- und Betriebshandbuch

Notice: This document contains references to Agilent.

Please note that Agilent’s Test and Measurement busi-

ness has become Keysight Technologies. For more in-

formation, go to www.keysight.com.

Keysight PXA Signal Analyzer

Option EXM

External Mixing Upgrade Kit

Installation Note

Part Number N9030-90058

Printed in USA August 2014

Notice.

The information contained in this document is subject to change without notice.

Keysight Technologies makes no warranty of any kind with regard to this material, including but not

limited to, the implied warranties of merchantability and fitness for a particular purpose. Keysight

Technologies shall not be liable for errors contained herein or for incidental orconsequential damages

inconnection with the furnishing, performance, or use of this material.

Installation Note N9030-90058 3

Option EXM, External Mixing Upgrade Kit

Software and test equipment is required for making adjustments and for performance verification

testing.

Information on how to obtain this software can be found at:

www.agilent.com/find/calibrationsoftware

While Agilent does recommend that a full calibration be performed after the installation of this

upgrade, the end user must ultimately determine whether they want this service or not. If a full

calibration is required, arrangements regarding the level of calibration must be made between the end

user and the calibration provider.

NOTE Option EXM requires instrument software A.10.00 or later. The latest revision of

the analyzer software may be downloaded from:

http://www.agilent.com/find/xseries_software

Products Affected: PXA N9030A

Serial Numbers: US/MY/SG51160000 and above

(Options 543, 544, and 550)

US/MY/SG51380000 and above

(Options 503, 508, 513, and 526)

To Be Performed By: (X) Agilent Service Center

(X) Personnel Qualified by Agilent

( ) Customer

Estimated Installation Time:

Estimated Adjustment Time:

Estimated Verification Time:

1.5 Hours

1.0 Hoursa

4.0 Hoursa

a. To ensure that these newly installed options are functioning properly, the procedure that follows

includes the requirement of performing certain adjustments and performance verification tests.

However, the completion of these tests does not guarantee that the instrument meets all advertised

specifications.

4Installation Note N9030-90058

Option EXM, External Mixing Upgrade Kit

Introduction

This kit includes parts to upgrade a PXA signal analyzer with frequency range option 503, 508, 513,

or 526 and serial number US/MY/SG51380000 or later or with frequency range option 543, 544, or

550 and serial number US/MY/SG51160000 or later to add option EXM, External Mixing. This kit

includes parts to upgrade a PXA regardless of frequency range option installed. As a result, some parts

included in this kit will not be needed for upgrading some analyzers.

In addition to installing the hardware to support option EXM, licenses for the following options will

also be installed:

• N9030A-EXM, External Mixing

• Licenses for core instrument software enhancements. For a list of these enhancements see:

http://www.agilent.com/find/N9030AK-R2C

Installation Note N9030-90058 5

Option EXM, External Mixing Upgrade Kit

Installation Kit Parts List

Quantity Description Agilent Part

Number

1 Adapter- Coaxial Straight Female-SMA to Female-SMA, 501250-1666

1 Washer, Lock, Internal Tooth, ¼ inch 2190-0067

1 Nut-Hex-Double-Chamfer 1/4-36-THD.125-IN-THK, Stainless Steel 2950-0223

1 50 Ohm Termination, SMA male 1810-0118

1 Opt EXM Cable Kit with Wire Markers (includes two versions of

cable W30, listed below) N9030-60014

1 Cable Assembly, External Mixing, Front Panel (W29) N9020-20166

1 Cable Assembly, uW Front End to W29 (W17) (for use in RF and

microwave analyzers) N9020-20132

1 Cable Assembly, mmW Front End to W29 (W17) (for use in

millimeter wave analyzers) N9020-20167

1 Cable Assembly, Coaxial 275 mm LG (W30) (for use in millimeter

wave analyzers) 8120-2025awith ends

labeled ‘903’ and ‘13’

a. This cable is included in the Opt EXM Cable Kit with Wire Markers, p/n N9030-60014.

1 Cable Assembly, Coaxial 350 mm LG (W30) (for use in RF and

microwave analyzers) 8120-2027awith ends

labeled ‘903’ and ‘13’

1 Label, External Mixing N9030-80014

1 Label, Warning N9030-80018

5 Cable Ties 1400-0249

1 Entitlement Certificate 5964-5178

1 Entitlement Certificate Envelope 5967-7169

1 Installation Note This note

6Installation Note N9030-90058

Option EXM, External Mixing Upgrade Kit

Tools Required

❏T-10 TORX Driver

❏T-20 TORX Driver

❏5/16-inch torque wrench

❏¼-inch open-end wrench

❏Diagonal cutters

❏Agilent Calibration and Adjustment Software, N7814A (revision E.08.00 or later)

❏Test equipment and computer supported by the X- Series Performance Tests and Adjustment

Software

❏PXA Signal Analyzer Service Guide. This manual is available as:

— N9030A Option OBW or

— Agilent part number N9030-90030

❏Microsoft Windows based personal computer with internet access and USB port

❏USB storage device with > 2 GB free memory

Initial Instrument Functionality Check

Power on the instrument and allow the instrument to boot up. Run an alignment and display the

measurement screen. (The instrument will probably display a spectrum analyzer screen and you will

see the instrument sweeping.)

There should be no alignment failures. If there are failures, investigate and fix the problem before

continuing.

WARNING Before you disassemble the instrument, turn the power switch to Standby.

After the instrument has completely shut down, unplug the instrument.

Failure to unplug the instrument can result in personal injury.

CAUTION Electrostatic discharge (ESD) can damage or destroy electronic components. All

work on electronic assemblies should be performed at a static-safe workstation.

Refer to the documentation that pertains to your instrument for information about

static-safe workstations and ordering static-safe accessories.

Installation Note N9030-90058 7

Option EXM, External Mixing Upgrade Kit

Installation Procedure

1. Connect a power cord to the analyzer and turn on the analyzer.

2. After the analyzer has completed turning on, press System, Show, System. Make note of the

following information from the Show System screen:

Product Number: _____________

Serial Number: ______________

Instrument S/W Revision: ______________

3. Check for the presence of one of the following frequency range options listed below in the Show

System. Put a check mark or “X” after the frequency range option listed below that appears in the

Show System menu.

N9030A-503_____

N9030A-508_____

N9030A-513_____

N9030A-526_____

N9030A-543_____

N9030A-544_____

N9030A-550_____

4. On the analyzer, press System, Show, Hardware. Note the Part #, Matl Rev, Rev, OF Rev, and

Hw Id of the Front End in the table below.

5. If the analyzer is equipped with any of the following frequency range options (refer to the data in

step 3 above):

N9030A-503

N9030A-508

N9030A-513

N9030A-526

And the part number of the Front End is one of the following:

N9020-60050

do not proceed with the installation of this upgrade kit.

An RF or microwave PXA with the N9020-60050 Front End assembly installed is not compatible

with Opt EXM. In this case, you should instead order N9030AK-HL6, which includes a new,

EXM-compatible, Front End Assembly.

Assembly Name Part # Matl Rev Rev OF Rev Hw Id

Front End

8Installation Note N9030-90058

Option EXM, External Mixing Upgrade Kit

Analyzer Disassembly

CAUTION If the instrument is placed on its face during any of the following procedures, be

sure to use a soft surface or soft cloth to avoid damage to the front panel, keys, or

input connector.

NOTE Make sure any adapters on the front panel are removed.

1. Disconnect the instrument from ac power.

2. Refer to Figure 1. Using the T-20 driver, remove the 4 screws (1) (two on each side) that attach

the handle strap (2) on each side of the instrument.

3. Remove the four key locks from the instrument four bottom feet.

4. Remove the four instrument bottom feet (6).

5. Using the T-20 driver, remove the four screws (including washers) (3) that hold the rear feet (4)

in place.

6. Pull the instrument cover (5) off towards the rear of the instrument.

Installation Note N9030-90058 9

Option EXM, External Mixing Upgrade Kit

Figure 1 Instrument Outer Case Removal

10 Installation Note N9030-90058

Option EXM, External Mixing Upgrade Kit

Top Brace Removal

Refer to Figure 2. To remove the top brace (1), use the T-10 driver to remove the twelve screws (3)

(0515-0372) attaching the top brace to the chassis. Remove the wire hold down 1 (as shown in Figure

3). Remove the twelve screws (14 screws with Option B1X) (4) (0515-1227) attaching the top brace

to the boards.

Figure 2 Top Brace Removal

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Keysight Messgerät Handbücher

Keysight

Keysight PNA-X Series Bedienungsanleitung

Keysight

Keysight PNA E8362C Bedienungsanleitung

Keysight

Keysight M3102A PXIe Bedienungsanleitung

Keysight

Keysight P-Series Bedienungsanleitung

Keysight

Keysight x-series Bedienungsanleitung

Keysight

Keysight x series Installations- und Betriebshandbuch

Keysight

Keysight N9020A Bedienungsanleitung

Keysight

Keysight 85024A Handbuch

Keysight

Keysight M9601A Bedienerhandbuch

Keysight

Keysight N2862B Bedienungsanleitung

Keysight

Keysight E5052B Bedienungsanleitung

Keysight

Keysight M9202A Benutzerhandbuch

Keysight

Keysight Y1301A Bedienungsanleitung

Keysight

Keysight M9005A Bedienungsanleitung

Keysight

Keysight E4981A Bedienungsanleitung

Keysight

Keysight N1913 Bedienungsanleitung

Keysight

Keysight U1190A Series Bedienungsanleitung

Keysight

Keysight 8990B Bedienungsanleitung

Keysight

Keysight N1911A Bedienungsanleitung

Keysight

Keysight u2722a Bedienungsanleitung

Keysight

Keysight N5244AU-940 Bedienungsanleitung

Keysight

Keysight N9030B Installations- und Betriebshandbuch

Keysight

Keysight x-series Bedienungsanleitung

Keysight

Keysight N9030A-503 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung

Konica Minolta

Konica Minolta BC-10 Plus Bedienungsanleitung