Kichler Lighting Motu Bedienungsanleitung

Instruction Manual

MotuTM

330010

UL Model #330010xxx

Includes Wall Control

1. To reduce the risk of electric shock, insure

electricity has been turned off at the circuit

breaker or fuse box before beginning.

2. All wiring must be in accordance with the

National Electrical Code and local electrical

codes. Electrical installation should be

performed by a qualied licensed electrician.

3. WARNING: To Reduce The Risk Of Fire Or

Electric Shock, Do Not Use This Fan With

Any Solid-State Speed Control Device. Only

use the remote control provided by ceiling

fan manufacturer.

4. WARNING: To reduce the risk of personal

injury, use only the two steel screws (and

lock washers) provided with the outlet box for

mounting to the outlet box. Most outlet boxes

commonly used for the support of lighting

xtures are not acceptable for fan support

and may need to be replaced, consult a

qualied electrician if in doubt.

5. The outlet box and support structure must

be securely mounted and capable of reliably

supporting a minimum of 50 pounds. Use

only CUL Listed outlet boxes marked “FOR

FAN SUPPORT”.

6. The fan must be mounted with a minimum

of 10 feet clearance from the trailing edge of

the blades to the oor.

7. Avoid placing objects in the path of the

blades.

8. To avoid personal injury or damage to the fan

and other items, be cautious when working

around or cleaning the fan.

9. Do not use water or detergents when cleaning

the fan or fan blades. A dry dust cloth or

lightly dampened cloth will be suitable for

most cleaning.

10. After marking electrical connections, spliced

conductors should be turned upward and

pushed carefully up into outlet box. The wires

should be spread apart with the grounded

conductor and the equipment-grounding

conductor on one side of the outlet box.

11. Electrical diagrams are reference only. Light

Kits that are not packed with the fan must be

CUL Listed and marked suitable for use with

the model fan you are installing. Switches

must be CUL General Use Switches. Refer

to the Instructions packaged with the light

kits and switches for proper assembly.

12. Suitable for commercial or industrial use.

1. SAFETY RULES (READ AND SAVE THESE INSTRUCTIONS)

WARNING

TO REDUCE THE RISK OF FIRE,

ELECTRIC SHOCK OR PERSONAL INJURY,

MOUNT FAN TO OUTLET BOX MARKED

“ACCEPTABLE FOR FAN SUPPORT”

WARNING

TO REDUCE THE RISK OF PERSONAL

INJURY, DO NOT BEND THE BLADE

BRACKETS (ALSO REFERRED TO AS

FLANGES) DURING ASSEMBLY OR AFTER

INSTALLATION. DO NOT INSERT OBJECTS

IN THE PATH OF THE BLADES.

60” Motu™

2. TOOLS AND MATERIALS REQUIRED

• Phillips screw driver

• Blade screw driver

• 11mm wrench

• Step ladder

• Wire cutters

3. PACKAGE CONTENTS

Unpack your fan and check the contents.

You should have the following items:

a. Fan blade/blade arm assemblies (3)

b. Ceiling mounting bracket, Canopy and

Canopy bottom cover

c. Ball/downrod assembly

d. Coupling cover

e. Fan motor assembly

f. Fan bottom cap

g. Wall transmitter

h. Parts bag contents:

1) Mounting hardware:

Star washers (2), wire nuts (3),

machine screws (2), washers (2),

wood screws (2)

2) Blade attachment hardware screws (7)

3) Safety cable hardware:

wood screw, lock washer, at washer

4) Decorative nut

KICHLER

4. MOUNTING OPTIONS

If there isn’t an existing UL (cUL for Canadian

Installation) listed mounting box, then read the

following instructions. Disconnect the power by

removing fuses or turning off circuit breakers.

Secure the outlet box directly to the building structure.

Use appropriate fasteners and building materials. The

outlet box and its support must be able to fully support

the moving weight of the fan (at least 50 lbs). Do not

use plastic outlet boxes.

Figures 1, 2, and 3 are examples of different ways to

mount the outlet box.

NOTE: If you are installing the ceiling fan on a sloped

(vaulted) ceiling, you may need a longer downrod

to maintain proper clearance between the tip of the

blade and the ceiling. A minimum clearance of 12” is

suggested for optimal operation.

NOTE: Depending on the location you have selected

for installation, you may need to purchase and install

a “Joist Hanger” for the support of the outlet box.

Make sure the joist hanger you purchase has been

designed for use with ceiling fans. (Fig. 4)

Outlet box

Provide strong

support

Recessed

outlet box Ceiling

mounting

plate

Outlet box

ANGLED CEILING

MAXIMUM 30°

ANGLE

Fig. 2

Fig. 1

Fig. 3

Fig. 4

60” Motu™

Mounting screws

(supplied with

electrical box)

Hook

Ceiling

mounting

bracket

UL Listed

outlet box

120V Wires

Washers

Screws

Plastic Stabilizer

Cross pin

Hanger ball

Set screw

Downrod

Canopy

Canopy cover

5. HANGING THE FAN

REMEMBER to turn off the power before you

begin.

To properly install your ceiling fan, follow the

steps below.

Step 1. Remove the decorative canopy bottom

cover from the canopy by turning the cover

counterclockwise. (Fig. 5)

Step 2. Remove the ceiling mounting bracket

from the canopy by removing (and save) one of

the two screws. Loosen the remaining screw by

a half turn. (Fig. 5)

Step 3. Pass the 120 volt supply wires from

the ceiling outlet box through the center of the

ceiling mounting bracket. (Fig. 6)

Step 4. Attach the ceiling mounting bracket to

the outlet box using the screws and washers

included with the outlet box. (Fig. 6)

Step 5. Remove and discard the three screws

securing the plastic stabilizer on the bottom of

motor housing. Remove and discard the plastic

stabilizer. (Fig. 7)

Step 6. Remove the hanger ball from the

downrod assembly by loosening the setscrew,

removing the cross pin and turning the ball off

the downrod. (Fig.8)

Fig. 6

Fig. 5

Fig. 7

Fig. 8

Registration slot

Check tab

Retaining

clip

Hitch

Set screws

Downrod

Coupling

Supply wires

& Safety cable

Hanger ball

Cross pin

Set screw

Downrod

Coupling

Canopy

Canopy cover

Coupling

cover

Supply wires

& Safety cable

Step 7. Loosen the two setscrews and remove the

hitch pin and retaining clip from the coupling on top

of the motor assembly. (Fig. 9)

Step 8. Carefully route the electrical supply

wires and safety cable exiting the top of the fan

motor assembly through the downrod. Thread the

downrod into the coupling until the hitch pin holes

are aligned. (Fig. 9)

Next, replace the hitch pin and retaining clip.

Tighten both setscrews. (Fig. 9)

Step 9. Slip the coupling cover, canopy cover and

canopy onto the downrod. (Fig. 10)

Thread the hanger ball onto the downrod, insert the

cross pin through the downrod and tighten. Now

tighten the set screw. (Fig. 10)

Step 10. Lift the motor assembly into position and

place the hanger ball into the ceiling mounting

bracket.

Rotate the entire assembly until the “Check Tab”

has dropped into the “Registration Slot” and seats

rmly. (Fig. 11)

The entire motor assembly should not rotate (left or

right) when seated properly.

WARNING: Failure to reattach the cross pin and

seat the “Check Tab” can cause the fan to fall from

the ceiling during operation. Take special care to

make sure this pin is reattached.

Fig. 9

Fig. 10

Fig. 11

60” Motu™

6. INSTALLATION OF SAFETY SUPPORT

(Required for Canadian installation ONLY)

A safety support cable is provided to help prevent the

ceiling fan from falling, please install it as follows.

Step 1. Attach the provided wood screw and washers

to the ceiling joist next to the mounting bracket but do

not tighten. (Fig. 12)

Step 2. Adjust the length of the safety cable to reach

the screw and washers by pulling the extra cable

through the cable clamp until the overall length is

correct, put the end of the cable back through the cable

clamp, forming a loop at the end of the cable. Tighten

the cable clamp securely. Now, put the loop in the end

of the safety cable over the wood screw securely.

NOTE: Although the safety support cable is required

for Canadian installations only. It’s a good idea to make

the attachment with any installation.

7. ELECTRICAL CONNECTIONS

WARNING: To avoid possible electrical shock, be sure

you have turned off the power at the main circuit panel.

Follow the steps below to connect the fan to your

household wiring. Use the wire connecting nuts

supplied with your fan. Secure the connectors with

electrical tape. Make sure there are no loose wire

strands or connections.

Step 1. Connect the fan supply wire (black) to the black

household supply wire. (Fig. 13)

Step 2. Connect the neutral fan supply wire (white) to

the neutral household wire (white).

Step 3. Connect the fan ground wire (green) to the

household ground wire.

Step 4. After connecting the wires, spread them apart

so that the green and white wires are on one side of the

outlet box and the black wires are on the other side.

Step 5. Turn the connecting nuts upward and push the

wiring into the outlet box.

Fig. 12

Fig. 13

Hanger bracket

Safety cable Attach safety cable

to ceiling joist with

screw and washer

White (neutral)

Outlet box

Black (hot)

Ground

(green)

(Connect to

ground wire on

hanger bracket

if no house

ground wire

exists.)

White (neutral)

Black (motor)

Outlet box

Ceiling

mounting

bracket

Canopy

Canopy cover

Screw

Screws

Blade arm Blade

8. FINISHING THE INSTALLATION

Step 1. Tuck all the connections neatly into the ceiling

outlet box.

Step 2. Slide the canopy up to the mounting bracket

and place one of the key hole slots over the mounting

screw on the mounting bracket. Rotate the canopy until

the screw head locks in place at the narrow section of

the key hole. (Fig. 14)

Step 3. Align the remaining circular hole on the canopy

with the remaining hole on the Ceiling Mounting

Bracket. Insert and tighten the mounting screw from

step 2 above. Now, attach the canopy cover to the

mounting screw head by inserting the screw heads into

the bottom side of the canopy cover and rotating the

cover clockwise.

NOTE: Adjust the canopy screws as necessary until

the canopy and canopy cover are snug. (Fig. 14)

9. ATTACHING THE FAN BLADE/

BLADE ARM ASSEMBLIES

Attach each blade assembly to the motor by using

two mounting screws for each blade assembly.

(Fig. 15)

NOTE: Make sure these mounting screws are

securely tightened.

Fig. 14

Fig. 15

60” Motu™

10. INSTALLING THE BOTTOM CAP

Step 1. Remove and save the two pre-attached

screws on the mounting ring attached to the

motor shaft. (Fig. 16)

Step 2. Push up the bottom cap to the mounting

ring and align the holes on the bottom cap and

mounting ring.

Step 3. Secure the bottom cap by installing the

two screws removed in the rst step and tighten

them.

Step 4. Install the decorative nut by screwing it

into the shaft. (Fig. 17)

11. OPERATING INSTRUCTIONS

-= Power Off

1 = High Speed

2 = Medium-High Speed

3 = Medium-Low Speed

4 = Low Speed

Bottom cap

Screws

Decorative nut

KICHLER R

Fig. 17

Fig. 18

Fig. 16

12. INSTALLING THE BASIC FUNCTION

WALL CONTROL SYSTEM WALL PLATE

Select a location to install the Basic Function Wall

Control System Transmitter and Wall Plate.

Install the wall plate using an existing wall switch

outlet box. Make sure the electrical power is

TURNED OFF at the main panel before continuing.

Step 1. Remove the existing wall plate and the old

switch from the wall outlet box. (Fig. 19)

Step 2. Connect the green/yellow wire from wall

control to the green or bare wires in the outlet box,

secure with the wire nut. (Fig. 20)

Step 3. Connect the household white wire to the

white wire to the ceiling fan, secure with a wire nut.

(Fig. 20)

Step 4. Connect the household black wire to the

black wire marked “TO POWER SUPPLY”, secure

with a wire nut.

Step 5. Connect the household black wire to the

black wire marked “TO FAN”, secure with a wire

nut. (Fig. 20)

Step 6. Separate the black wires from the white

and green wires. Turn the green and white wires

into the outlet box. (Fig. 20)

Step 7. Turn the black wires into the outlet box.

(Fig. 20)

Wall plate

Switch

Outlet box

CEILING FAN

SUPPLY WIRES

GREEN/YELLOW

TO HOUSEHOLD

GREEN / BARE

BLACK (TO AC IN L) TO

HOUSEHOLD BLACK

BLACK

(TO MOTOR L)

BLACK

(CEILIING FAN SUPPLY)

GREEN or

BARE

HOUSEHOLD

WHITE TO

WHITE (CEILIING

FAN SUPPLY)

HOUSEHOLD

WIRING

KICHLER

Fig. 19

Fig. 20

Inhaltsverzeichnis

Sprachen:

Andere Kichler Lighting Lüfter Handbücher

Kichler Lighting

Kichler Lighting Canfield Select Bedienungsanleitung

Kichler Lighting

Kichler Lighting KOSMUS Bedienungsanleitung

Kichler Lighting

Kichler Lighting Kittery Point Bedienungsanleitung

Kichler Lighting

Kichler Lighting Renew Select Bedienungsanleitung

Kichler Lighting

Kichler Lighting Almere Bedienungsanleitung

Kichler Lighting

Kichler Lighting Hatteras Bay Patio Bedienungsanleitung

Kichler Lighting

Kichler Lighting Decor Dorset Bedienungsanleitung

Kichler Lighting

Kichler Lighting Fit Bedienungsanleitung

Kichler Lighting

Kichler Lighting Hatteras Bay Patio Bedienungsanleitung

Kichler Lighting

Kichler Lighting 35153 Handbuch

Kichler Lighting

Kichler Lighting VASSAR Bedienungsanleitung

Kichler Lighting

Kichler Lighting Monarch II Bedienungsanleitung

Kichler Lighting

Kichler Lighting Crystal Bay Bedienungsanleitung

Kichler Lighting

Kichler Lighting Chicago Bedienungsanleitung

Kichler Lighting

Kichler Lighting Spyn Bedienungsanleitung

Kichler Lighting

Kichler Lighting Sunburst 300170 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Windham Bedienungsanleitung

Kichler Lighting

Kichler Lighting Monarch II Patio Bedienungsanleitung

Kichler Lighting

Kichler Lighting Arkwet Patio Bedienungsanleitung

Kichler Lighting

Kichler Lighting Selectlight fixture Bedienungsanleitung

Kichler Lighting

Kichler Lighting Decor Kimberley Bedienungsanleitung

Kichler Lighting

Kichler Lighting Lija Bedienungsanleitung

Kichler Lighting

Kichler Lighting 35157 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Spyn Lite Bedienungsanleitung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung