Kichler Lighting Highland Manor Bedienungsanleitung

Highland ManorTM

Includes our new

CoolTouchTM Control System

Looks permanent, but goes wherever you go!

U.S. Patent Pending

Kichler®Lighting

7711 East Pleasant Valley Road

P.O. Box 318010

Cleveland, Ohio 44131-8010

Customer Service

866.558.5706

8:30 AM to 5:00 PM EST,

Monday - Friday

A Kichler®Décor™ceiling fan

Designed to coordinate with a popular Kichler Lighting collection.

Instruction Manual

1. To reduce the risk of electric shock, insure

electricity has been turned off at the circuit

breaker or fuse box before beginning.

3. WARNING: To reduce the risk of electrical

shock and fire, do not use this fan with any

solid-state fan speed control device.

4. WARNING: To reduce the risk of fire,

electric shock, or personal injury, mount to

outlet box marked "Acceptable for Fan

Support"

and use mounting screws provided with

the outlet box. Most outlet boxes

commonly used for the support of light

fixtures are not acceptable for fan support

and may need to be replaced. Due to the

complexity of the installation of this fan, a

qualified licensed electrician is strongly

recommended.

5. The outlet box and support structure must

be securely mounted and capable of

reliably supporting a minimum of 50

pounds. Use the outlet boxes marked

"FOR FAN SUPPORT".

6. The fan must be mounted with a minimum

of 7 feet clearance from the trailing edge of

the blades to the floor.

7. To operate the reverse function on this fan,

press the reverse button while the fan is

running.

8. Avoid placing objects in the path of the

blades.

9. To avoid personal injury or damage to the

fan and other items, be cautious when

working around or cleaning the fan.

10. Do not use water or detergents when

cleaning the fan or fan blades. A dry dust

cloth or lightly dampened cloth will be

suitable for most cleaning.

11. After marking electrical connections,

spliced conductors should be turned

upward and pushed carefully up into outlet

box. The wires should be spread apart with

conductor of a fan identified as grounded

condutor to be connected to a grounded

conductor of power supply,conductor to be

connected to an ungrounded conductor of

power supply,conductor of fan identified for

equipment grounding to be connected to an

equipment-grounding conductor.

12. Electrical diagrams are for reference only.

Light kits that are not packed with the fan

must be marked suitable for use with the

model fan you are installing.Refer to the

Instructions packaged with the light kits and

switchesI for proper assembly.

NOTE: NOT SUITABLE FOR USE WITH SOLID-

STATE SPEED CONTROLS.

1. SAFETY RULES

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK OR PERSONAL INJURY, MOUNT FAN TO

OUTLET BOX MARKED "ACCEPTABLE FOR FAN

SUPPORT".

WARNING

TO REDUCE THE RISK OF PERSONAL INJURY

DO NOT BEND THE BLADE BRACKET WHEN

INSTALLING THE BRACKETS, BALANCING THE

BLADES, OR CLEANING THE FAN. DO NOT

INSERT FOREIGN OBJECTS IN BETWEEN ROTAT-

ING FAN BLADES.

All wiring must be in accordance with the

National Electrical Code, ANSI/NFPA70-1999

and local electrical codes. Electrical installa-

tion should be performed by a qualified

licensed electrician.

3. PACKAGE CONTENTS

Unpack your fan and check the contents. You

should have the following items:

Philips screw driver

Slot screw driver

11 mm wrench

Step ladder

Wire cutters

2. TOOLS AND MATERIALS REQUIRED

Highland ManorTM

a. Canopy (1)

b. Canopy Décor (1)

c. Mounting Bracket (1)

d. Ball / Downrod Assembly (1)

& Extra Downrod (1)

e. Rod Decoration 2 (1)

f. Rod Decoration 1 (1)

g. Fan Assembly (1)

h. Fan Blades (5)

i. Blade Brackets (5)

j. Mounting Plate (1)

k. Light kit (1)

l. Glass Bowl (1)

m. Receiver + 7 Wire Nuts

n. CoolTouch™ Control System

o. Package Hardware:

1) Mounting hardware:

a. wood screws (2), flat washers(2),

screws(2),wire nuts(4)

2) Blade Attachment Hardware:

a. screws (16), flat washers(16),

fiber washers(16)

3) Blade Bracket Hardware:

a. screws (11)

4) Light kit Hardware:

a. screws (4)

5)Safety Cable Hardware:

a. wood screw (1), spring washer (1),

flat washer (1)

6) Balance Kit (1)

p. Light Kit Hardware

a. manual nut (1), silicon washer (1),

metal washer (1), finial (1)

4. MOUNTING OPTIONS

Secure the outlet box directly to the building

structure. Use appropriate fasteners and

building materials. The outlet box and its

support must be able to fully support the

moving weight of the fan (at least 50 lbs). Do

not use plastic outlet boxes.

Figures 1,2 and 3 are examples of different

ways to mount the outlet box.

NOTE: You may need a longer downrod to

maintain proper blade clearance when

installing on a steep, sloped ceiling. (Fig. 3)

To hang your fan where there is an existing

fixture but no ceiling joist, you may need a

joist hanging bracket as shown in Fig 4.

Outlet box

Provide strong

support

Recessed

outlet box Ceiling

mounting

plate

Outlet box

Fig. 1

Fig. 3

Fig. 4

Outlet box

Fig. 2

If there isn't an existing UL ( CUL for Canadian

Installation) listed mounting box, then read the

following instructions. Disconnect the power by

removing fuses or turning off circuit breakers.

Highland ManorTM

5. HANGING THE FAN

REMEMBER to turn off the power. Follow the

steps below to hang your fan properly:

Step 2. Secure the mounting bracket to the

ceiling outlet box using screws and washers

provided with the outlet box. (Fig. 6)

Step 4. Loosen the two set screws and

remove the hitch and lock pin from the

motor coupling assembly. (Fig. 8)

Step 1. Remove the fan motor and housing

assembly from the protective plastic bag

and take the lower Styrofoam packing pad

out of the carton. Place the Styrofoam pad

on the floor, then place the fan assembly

into the Styrofoam pad with the bottom of

the motor facing up. (The Styrofoam pad

serves as a holder for the fan during the first

stages of assembly). Remove the plastic

motor shipping blocks and discard. (Fig. 5)

Step 5. Carefully feed fan electrical wires up

through the downrod. Thread the downrod

onto the motor coupling until the hitch pin

holes are aligned. Next, replace hitch pin and

lock pin, and tighten both set screws. (Fig. 8)

Step 3. Use a screwdriver to loose the cross

pin and removeit from downrod assembly.

Loose the set screw and rotate the hanger

ball off the downrod. (Fig. 7)

Fig. 7

Fig. 5

Fig. 6

Fig. 8

Shipping block

Screw

Supply wires

Downrod

Lock pin Hitch pin

Set Screw

Downrod

Hanger Ball

Cross Pin

Set Screw

Washer

120 V wires

Mounting screw

listed electrial box

Mounting bracket

Fig. 10

Fig. 9

Registration slot

Step 7. Now lift the motor assembly into position

and place the hanger ball into the hanger

bracket. Rotate motor assembly until the “Check

Tab” has dropped into the “Registration Slot”

and seats firmly. (Fig. 10)

NOTE: The entire motor assembly should not

rotate if this is done correctly.

Step 6. Loose the screw on the bottom of the rod

decoration 2. Slip the rod decoration 1, rod deco-

ration 2, canopy décor and canopy onto the

downrod. Reinstall the hanger ball onto the

downrod and make sure the cross pin is in place

and the set screw on hanger ball is tight. Finally

let the rod decoration 2 seat on the top of the rod

decoration 1 and tighten the screw loosened

previously. (Fig. 9)

NOTE: If you choose to use the shorter downrod,

please ignore to install the “rod decoration 2”.

Canopy cover

Canopy

Supply wires

Rod Decoration 2

Rod Decoration 1

Screw

NOTE:Please make sure all set screws are in

place and tight before installation the following

steps.

Highland ManorTM

6. INSTALLATION OF SAFETY SUPPORT

( For Canadian Installation ONLY )

Fig. 11-2

Fig. 11-1

Fig. 12

Fig. 13

7. MAKE THE ELECTRIC CONNECTIONS

Code switch

Receiver

Hanger

bracket

Battery Compartment

A safety support cable is provided to help prevent

the ceiling fan from failing, please install it as

follows.

Step 1. Attach the provided wood screw and

washers to the ceiling joist next to the mounting

bracket but do not tighten. (Fig. 11-1)

Step 2. Adjust the length of the safety cable to

reach the screw and washers by pulling the extra

cable through the cable clamp until the overall

length is correct, put the end of the cable back

through the cable clamp, forming a loop at the

end of the cable. Tighten the cable clamp

securely. Now, put the loop in the end of the

safety cable over the wood screw and under the

washer. Tighten the wood screw securely. See

Fig. 11-2

WARNING: To avoid possible electrical shock,

be sure the electricity is turned off at the main

circuit breader or fuse box before wiring.

WARNING: If your house wires are different

colors than referenced in this manual, stop

immediately. A professional electriccian is

recommended to determine proper wiring.

NOTE: The CoolTouch™ Control System is

equipped with 16 code combinations to prevent

possible interference from or to other remote

units. The frequency switches on your receiver

and transmitter have been preset at the factory.

Please recheck to make sure the switches on

the transmitter and receiver are set to the same

position, any combination of setting will operate

the fan as long as each switch on the transmitter

and receiver are set to the same opposition.

(Fig. 12) Changing the order of switches on

each switch block, changes the operational

frequency.

Step 1. Insert the receiver into the mounting

bracket, with the flat toward the ceiling. (Fig. 13)

Step 2. Motor to Receiver Electrical Connec-

tions:

NOTE: Make ALL of the following connections

with “Wire Nut” connectors.

Connect the black wire from the fan to black

wire marded “TO MOTOR L” from the receiver.

Connect the white wire from the fan to the white

wire marked “TO MOTOR N” from the receiver.

Connect the blue wire from the fan to the blue

wire marked “FOR Bottom Light” from the

receiver. Place a plastic wire nut on the end of

the Orange Wire coming from the receiver

marked “For Upper Light”. Your ceiling fan is not

equipped with a Upper Light. Secure all the wire

connections with the plastic wire nut provided.

(Fig. 14 on the next page)

Ceiling

Support Brace

Outlet Box

Wood Screw

Flat Screw

Spring Washer

Wood Screw

Safety Cablebolt

Fig. 14

Fig. 15

8. INSTALLING THE CEILING CANOPY

Step 3. Remote Receiver to Outlet Box Electri-

cal Connections: Connect the black

(hot) wire from the ceiling to the black wire

marked "AC in L" from the receiver. Connect

the white(neutral) wire from the ceiling to the

white wire marked "AC in N" from the

Receiver. Secure the wire connections with

the plastic wire nuts provided. (Fig. 14)

Step 4. If your outlet box has a ground wire

(green or bare copper) connect it to the fan

ground wires; otherwise connect the hanging

bracket ground wire to the mounting bracket.

Secure the wire connection with a plastic nut

provided.

NOTE: Carefully tuck the wire connections up

into the outlet box. (Fig. 14)

NOTE: The transmitting unit must be installed

at a maximum distance of 30 feet from the

ceiling fan for proper signal transmission

between the transmitting unit and the fan’s

receiving unit.

WARNING: One last time, make sure the “Check

Tab” at the bottom of the hanger bracket is prop-

erly seated in the “Registration Slot” on the side

of the hanger ball before attaching the canopy to

the bracket. Failure to properly seat the “Check

Tab” could damage the electrical wires when to

ceiling fan blade direction is changed while the

fan is running.

Step 1. Make sure all of the electrical connec-

tions are tucked neatly into ceiling outlet box.

Step 2. Slide the canopy up to ceilng fan and

onto the two screws on hanger bracket. Rotate

the canopy clockwise and tighten the two screws.

Next, while holding the canopy with one hand,

slide the canopy décor over the screws and

rotate clockwise until tight.

NOTE: You may need to adjust the canopy

mounting screws as necessary until the canopy

and canopy cover have a snug fit. (Fig. 15)

Blue(motor)

Black(motor)

White(neutral)

White("to motor N")

Receiver

Ground wire

Orange

(for upper light)

Blue(for bottom light)

Black("to motor L")

White("AC IN N")

Green or bare

copper(ground)

White(neutral)

Black("AC IN L")

Black(hot)

Outlet box

Canopy

Canopy ring

Highland ManorTM

9. ASSEMBLYING AND ATTACHING

THE FAN BLADES

Fig. 16

Fig. 17

Fig. 18

10. INSTALLATING THE MOUNTING PLATE

Step 1. Remove 1 of the 3 screws on the

mounting ring and loosen the other 2 screws.

Do not remove (the mounting ring located on

the motor shaft).

Step 2. Place the key holes on the mounting

place over the 2 screws previously loosened

and turn the mounting plate until it locks in

place at the narrow end of the key holes.

Secure by tightening the 2 screws previously

loosened and reinsall the one removed. (Fig.

18)

Step 1. Attach the blade to the blade bracket

using the screws, washers and fiber washers

provided. Refer to Fig. 16 as needed. Start

each screw into the bracket. Repeat for the

two (2) remaining screws.

Step 2. Make sure the blade is straight and

tighten each screw until the fiber washer is

slightly compressed and all three screws are

secure.

Step 3. Insert the blade assembly into one of

the slots on the blade bracket ring, align the

mounting holes on the blade bracket with the

mounting holes on the inside of the bracket

ring and insert two (2) mounting screws and

tighten securely. Repeat this procedure for the

remaining four (4) blade assemblies. See Fig.

17 as needed.

Blade Bracket

Blade

Mounting Plate

Screw

Mounting Screw

Mounting Ring

Metal washer

Screw

Silicon washer

Blade Bracket

Fig. 20

Fig. 19

12. INSTALLING THE LIGHT BULB

& GLASS BOWL

11. INSTALLING THE LIGHT KIT

NOTE: Before continuing, make sure the power

is disconnected by turning off the circuit breaker

of removing the fuse at the circuit box.

Step 1. Remove the 3 screws on the mounting

plate.

Step 2. The square wiring connector from the

ceiling fan and the light fixture will only fix

together one way. Match up the same color on

the side of the connector, then push them

together until the snap engages. (Fig. 19)

Step 2. Tuck the connections neatly into the

mounting plate. Align the holes on the mounting

plate and light kit. Tighten the 3 screws removed

previously and make sure all three are tight

securely. (Fig. 19)

Step 1. Install three 40 watt lamp into each of

the three sockets in the light fixture.

Step 2. Slide the glass bowl over the threaded

pipe on the light fixture. Place the silicon

washer, metal washer and thread the manual

nut onto the pipe. Attach and tighten the decora-

tive finial. (Fig. 20)

Step 1. Install three 40 watt lamp into each of

the three sockets in the light fixture.

Step 2. Slide the glass bowl over the threaded

pipe on the light fixture. Place the silicon

washer, metal washer and thread the manual

nut onto the pipe. Attach and tighten the decora-

tive finial. (Fig. 20)

Mounting Plate

Light Kit

Glass Bowl

Silicon Washer

Metal Washer

Manual Nut

Finial

Screw

AMP Connection

Inhaltsverzeichnis

Andere Kichler Lighting Lüfter Handbücher

Kichler Lighting

Kichler Lighting 35166 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Surrey Climates 60 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Monarch II Bedienungsanleitung

Kichler Lighting

Kichler Lighting 330015WH Bedienungsanleitung

Kichler Lighting

Kichler Lighting 35153 Handbuch

Kichler Lighting

Kichler Lighting PINION 60 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Vassar 330002OZ Bedienungsanleitung

Kichler Lighting

Kichler Lighting Monarch II Select Bedienungsanleitung

Kichler Lighting

Kichler Lighting Olympia Bedienungsanleitung

Kichler Lighting

Kichler Lighting Ried 300356 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Seaside Bedienungsanleitung

Kichler Lighting

Kichler Lighting 42 STRATMOOR Bedienungsanleitung

Kichler Lighting

Kichler Lighting Ridley 300027OBB Bedienungsanleitung

Kichler Lighting

Kichler Lighting True Bedienungsanleitung

Kichler Lighting

Kichler Lighting 54 Meredith Bedienungsanleitung

Kichler Lighting

Kichler Lighting Industrial Fan Bedienungsanleitung

Kichler Lighting

Kichler Lighting Bentzen Bedienungsanleitung

Kichler Lighting

Kichler Lighting Kittery Point Bedienungsanleitung

Kichler Lighting

Kichler Lighting FRYST Bedienungsanleitung

Kichler Lighting

Kichler Lighting SPYRA Bedienungsanleitung

Kichler Lighting

Kichler Lighting 35157 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Larissa Bedienungsanleitung

Kichler Lighting

Kichler Lighting Rana 310155 Bedienungsanleitung

Kichler Lighting

Kichler Lighting BASICS PRO SELECT 330017MWH Bedienungsanleitung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung